| Rabouyt D2 | |
|---|---|
 | |
| The prototype Rabouyt D2 "Heliplane" displayed at the June 1971 Paris Air Show. | |
| Role | Two seat hybrid helicopter/autogyro |
| National origin | France |
| Manufacturer | Rabouyt |
| Introduction | 1971 |
| Number built | 1 |
The Rabouyt D2 was a two-seat autogyro, with an engine driven rotor for vertical take-offs. In level flight the aircraft was powered by the same engine driving a shrouded, pusher configuration propeller. It was designed and built in France in the early 1970s by Denis Rabouyt.
The D2 was primarily an autogyro driven by a pusher configuration, shrouded propeller whilst supported by an autorotatiing undriven two blade rotor. It was unusual in that the rotor could be powered, by the same engine that drove the propeller, during a vertical take-off phase to overcome the autogyro's normal limiting need for a take-off run. [1]
The D2's main rotor had constant chord blades of laminated wood, covered with geodesic glass fibre fabric. They were pillar mounted, together with a torque limiting coupler, at mid fuselage between the cabin and engine compartment. The fuselage was a steel-chromium-vanadium pod, with two side by side seats in a cabin glazed to the nose and accessed by a forward opening door on each side. The pusher configuration engine was mounted behind the cabin, driving a four blade propeller turning within a circular, aerofoil shroud supported by a ventral pod extension and braced to the rotor pillar. A vertical tail consisting of a small fin and large rudder was mounted on a boom from the lower fuselage. The D2 landed on a fixed tricycle undercarriage, each wheel within a streamlined fairing on a cantilever leg. The nosewheel was steerable via the rudder pedals. [1]
The Rabouyt D2 first appeared in public at the Paris Air Show of 1971, though it is not known if the aircraft had flown by this date. For early testing it was fitted with a low powered engine which was being replaced in early 1973 by a 150 hp flat-four of unspecified type. [2] It is not known if it was flown.
Data from Jane's All the World's Aircraft 1974-75 [1] All performance figures are estimates at the maximum take-off weight.
General characteristics
Performance
The Bensen B-8 is a small, single-seat autogyro developed in the United States in the 1950s. Although the original manufacturer stopped production in 1987, plans for homebuilders are still available as of 2019. Its design was a refinement of the Bensen B-7, and like that aircraft, the B-8 was initially built as an unpowered rotor-kite. It first flew in this form in 1955, and on 6 December a powered version, designated B-8M first flew. The design proved to be extremely popular and long-lasting, with thousands of sets of plans sold over the next thirty years.
The McDonnell XV-1 is an experimental gyrodyne developed by McDonnell Aircraft for a joint research program between the United States Air Force and the United States Army to explore technologies to develop an aircraft that could take off and land like a helicopter but fly at faster airspeeds, similar to a conventional airplane. The XV-1 would reach a speed of 200 mph, faster than any previous rotorcraft, but the program was terminated due to the tip-jet noise and complexity of the technology which gave only a modest gain in performance.
The Pitcairn PA-34 and Pitcairn PA-33, given the United States Navy (USN) designation Pitcairn OP-2 and United States Army designation Pitcairn YG-2 respectively were reconnaissance auto-gyros designed and built in 1936 for evaluation.
The Avian 2/180 Gyroplane was a two-seat, single-engine autogyro built in Canada in the 1960s. Several prototypes were built but production was not achieved.
The Magni M-24 Orion is an Italian sport autogyro, seating two side-by-side in an enclosed cabin. It was designed and produced by Magni Gyro srl of Besnate.
The AAI SparrowHawk is an American two-seat pusher ultralight autogyro, available in kit form for amateur construction.
The CSIR SARA II is a South African two-seat experimental autogyro designed and built by the Aeronautics Research Unit of the Council for Scientific and Industrial Research.
The Irkut A-002 is a three-seat, pusher configuration autogyro developed in Russia through the 2000s by the United Constructor Bureau for Light Aircraft team of the Irkutsk Aircraft Production Association (IAPO) "Irkut" as the first independent product. The take-off from a place is possible when speed of a wind exceeds 8 m/s, otherwise running start up to 15 m is necessary. The riveted covering is made of duralumin. The first produced consignment consisted of five autogyros. The A-002M is a further development.
The Aero-Astra Okhotnik is a Russian single engine, three seat autogyro of pusher, pod and boom configuration. It has been developed into several variants from 2001 to 2007.
The OSKBES MAI-208 is a single-engine, two-seat autogyro, designed and built in Russia, which utilises the fuselage of the MAI-223 ultralight. It had been completed but not flown by spring 2010.
The Groen Hawk 4 was a single engine, pusher configuration, four seat autogyro built in the United States in the late 1990s. Three prototypes, two piston engined and one turboprop powered, were flown but the Hawk did not go into production.
The Latécoère 225 was an unusual single seat canard microlight amphibian, with a swept wing, and of pusher configuration. It first flew in 1984 but was not put into production.
The Bede XBD-2 was an experimental short takeoff and landing (STOL) aircraft, with several novel features such as structural use of glass-fibre and aluminium honeycomb, a suction boundary layer control (BLC) system and fuselage-mounted twin engines driving a pusher configuration, shrouded single propeller. The sole example flew in the early 1960s in the United States.
The Kamerton-N Ratnik is a 1990s Russian light autogyro designed and built by Kamerton-N Ltd of Shchyolkovo.
The Phenix Aviation Phenix is a Spanish autogyro, under development by Phenix Aviation of Alicante. The aircraft is intended to be supplied as a complete ready-to-fly-aircraft.
The Farrington Twinstar is an American two-seat autogyro that was designed and produced by Farrington Aircraft of Paducah, Kentucky, a company owned by Don Farrington. Now out of production, when it was available the aircraft was supplied as a kit for amateur construction.
The Rotorwing-Aero 3D-RV is an American autogyro that was designed by Monte Hoskins and produced by Rotorwing-Aero of Salt Lake City, Utah, introduced in 1989. Now out of production, when it was available the aircraft was supplied in the form of plans for amateur construction.
The Rotorvox C2A is a two-seat, pusher configuration autogyro developed in Germany.
The 1933 experimental Pitcairn PA-22 was one of the first wingless autogyros. It was controlled by movement of the rotor plane rather than the usual control surfaces, though initially the much modified lone example retained rudders as a precaution.
The Wilford Gyroplane was based on a German autogyro first flown in 1926. After E. Burke Wilford bought the rights and patents, it was developed in the US until 1936.