Scribing (cartography)

Last updated

Scribing was used to produce lines for cartographic map compilations before the use of computer-based geographic information systems. Lines produced by manual scribing are sharp, clear and even.

Contents

An impression of the corrected compilation sheet is photographed onto scribe sheet material or drawn using pencil. While working over a light table, lines on the scribe sheet are traced with a metal or sapphire-tipped scribe tool to remove thin lines of translucent coating to produce a handmade negative image. This compares with drafting, where an ink image is made on tracing paper by depositing ink using a pen to produce a positive image. Scribing produces a result superior to drafting, but is more time-consuming. A separate stylus is required for each thickness of line required. For example, a contour line might require a 0.15mm stylus whereas a major road might require a 0.5mm stylus.

The scribe sheet is made of a stable plastic base material and coated with a material which is designed for easy removal using a scribing tool to produce a cleanly cut line. Various colours are used, and orange is said to produce the least eye-strain for the cartographer.

One scribe sheet is produced for each map colour. Corrections can be made by "duffing" (re-coating) the scribe sheet with special duffing liquid. The detail can then be re-scribed. Printing plates are produced from the finished scribe sheets, one for each colour of the map.

Scribe tools

A tripod or trolley arrangement is used to hold the scribe stylus. A stylus of required thickness is set in the trolley and the surface material is removed by applying light pressure as the trolley is moved over the image. Care must be taken to ensure the base material is not gouged or distorted.

Either a round point or chisel point stylus may be used. Chisel points must be set at right angles to the direction of movement. As well as single line gravers, double and triple lines can be produced with double and triple graver stylus. Small circles can be produced using motorised versions of scribing tools, and symbols, figures etc., can be produced using plastic or metal templates.

Area symbols

‘Peelcoat’ is used to produce a negative of an area of detail such as a lake or forest. The border of the area is cut or scribed on the peelcoat and the coat of the sheet within the area is peeled off to produce a negative image.


A stipple pattern can be used to produce an area symbol over the peeled surface. A stipple sheet with a simple repeating symbol (such as that for swamp or sand) is combined with the area by photographing the stipple onto the peelcoat.

Related Research Articles

Drawing Visual artwork in two-dimensional medium

Drawing is a form of visual art in which an artist uses instruments to mark paper or other two-dimensional surface. Drawing instruments include graphite pencils, pen and ink, various kinds of paints, inked brushes, colored pencils, crayons, charcoal, chalk, pastels, erasers, markers, styluses, and metals. Digital drawing is the act of drawing on graphics software in a computer. Common methods of digital drawing include a stylus or finger on a touchscreen device, stylus- or finger-to-touchpad, or in some cases, a mouse. There are many digital art programs and devices.

Lithography Printing technique

Lithography is a method of printing originally based on the immiscibility of oil and water. The printing is from a stone or a metal plate with a smooth surface. It was invented in 1796 by German author and actor Alois Senefelder as a cheap method of publishing theatrical works. Lithography can be used to print text or artwork onto paper or other suitable material.

Mimeograph Type of duplicating machine

A mimeograph machine is a low-cost duplicating machine that works by forcing ink through a stencil onto paper. The process is mimeography. A copy made by the process is a mimeograph.

Plotter Computer output device that draws lines on paper by moving a pen

A plotter is a machine that produces vector graphics drawings. Plotters draw lines on paper using a pen, or in some applications, use a knife to cut a material like vinyl or leather. In the latter case, they are sometimes known as a cutting plotter.

Screen printing Printing technique

Screen printing is a printing technique where a mesh is used to transfer ink onto a substrate, except in areas made impermeable to the ink by a blocking stencil. A blade or squeegee is moved across the screen to fill the open mesh apertures with ink, and a reverse stroke then causes the screen to touch the substrate momentarily along a line of contact. This causes the ink to wet the substrate and be pulled out of the mesh apertures as the screen springs back after the blade has passed. One colour is printed at a time, so several screens can be used to produce a multi-coloured image or design.

Printmaking Process of creating artworks by printing, normally on paper

Printmaking is the process of creating artworks by printing, normally on paper, but also on fabric, wood, metal, and other surfaces. "Traditional printmaking" normally covers only the process of creating prints using a hand processed technique, rather than a photographic reproduction of a visual artwork which would be printed using an electronic machine ; however, there is some cross-over between traditional and digital printmaking, including risograph. Except in the case of monotyping, all printmaking processes have the capacity to produce identical multiples of the same artwork, which is called a print. Each print produced is considered an "original" work of art, and is correctly referred to as an "impression", not a "copy". However, impressions can vary considerably, whether intentionally or not. Master printmakers are technicians who are capable of printing identical "impressions" by hand. Historically, many printed images were created as a preparatory study, such as a drawing. A print that copies another work of art, especially a painting, is known as a "reproductive print".

Engraving Incising designs by cutting into a surface

Engraving is the practice of incising a design onto a hard, usually flat surface by cutting grooves into it with a burin. The result may be a decorated object in itself, as when silver, gold, steel, or glass are engraved, or may provide an intaglio printing plate, of copper or another metal, for printing images on paper as prints or illustrations; these images are also called "engravings". Engraving is one of the oldest and most important techniques in printmaking. Wood engraving is a form of relief printing and is not covered in this article.

Printed circuit board Board to support and connect electronic components

A printed circuit board (PCB) is a laminated sandwich structure of conductive and insulating layers. PCBs have two complementary functions. The first is to affix electronic components in designated locations on the outer layers by means of soldering. The second is to provide reliable electrical connections between the component's terminals in a controlled manner often referred to as PCB design. Each of the conductive layers is designed with an artwork pattern of conductors that provides electrical connections on that conductive layer, while another manufacturing process adds vias - small and precisely located holes that are drilled through the laminate and then plated with copper. The vias are the electrical interconnection between layers that are otherwise insulated in the laminate structure and this allows a third dimension of connection between conductive layers in a controlled manner that is both reliable and cost-effective for mass production of electronic products.

Whiteprint

Whiteprint describes a document reproduction produced by using the diazo chemical process. It is also known as the blue-line process since the result is blue lines on a white background. It is a contact printing process which accurately reproduces the original in size, but cannot reproduce continuous tones or colors. The light-sensitivity of the chemicals used was known in the 1890s and several related printing processes were patented at that time. Whiteprinting replaced the blueprint process for reproducing architectural and engineering drawings because the process was simpler and involved fewer toxic chemicals. A blue-line print is not permanent and will fade if exposed to light for weeks or months, but a drawing print that lasts only a few months is sufficient for many purposes.

Scratchboard

Scratchboard or scraperboard, is a form of direct engraving where the artist scratches off dark ink to reveal a white or colored layer beneath. Scratchboard refers to both a fine-art medium, and an illustrative technique using sharp knives and tools for engraving into a thin layer of white China clay that is coated with dark, often black India ink. There is also foil paper covered with black ink that, when scratched, exposes the shiny surface beneath. Scratchboard can be used to yield highly detailed, precise and evenly textured artwork. Works can be left black and white, or colored.

Hatching

Hatching is an artistic technique used to create tonal or shading effects by drawing closely spaced parallel lines. When lines are placed at an angle to one another, it is called cross-hatching.

Tactile graphics, including tactile pictures, tactile diagrams, tactile maps, and tactile graphs, are images that use raised surfaces so that a visually impaired person can feel them. They are used to convey non-textual information such as maps, paintings, graphs and diagrams.

Technical pen Writing implement designed to make lines of constant width

A technical pen is a specialized instrument used by an engineer, architect, or drafter to make lines of constant width for architectural, engineering, or technical drawings. "Rapidograph" is a trademarked name for one type of technical pen. Technical pens use either a refillable ink reservoir or a replaceable ink cartridge.

Inkjet paper Paper designed for use with inkjet printers

Inkjet paper is a special fine paper designed for inkjet printers, typically classified by its weight, brightness and smoothness, and sometimes by its opacity.

Orienteering map

An orienteering map is a map specially prepared for use in orienteering competitions. It is a topographic map with extra details to help the competitor navigate through the competition area.

Technical drawing tool Tools and instruments used for accurate and precise manual drafting

Drafting tools may be used for measurement and layout of drawings, or to improve the consistency and speed of creation of standard drawing elements. Tools such as pens and pencils mark the drawing medium. Other tools such as straight edges, assist the operator in drawing straight lines, or assist the operator in drawing complicated shapes repeatedly. Various scales and the protractor are used to measure the lengths of lines and angles, allowing accurate scale drawing to be carried out. The compass is used to draw arcs and circles. A drawing board was used to hold the drawing media in place; later boards included drafting machines that sped the layout of straight lines and angles. Tools such as templates and lettering guides assisted in the drawing of repetitive elements such as circles, ellipses, schematic symbols and text. Other auxiliary tools were used for special drawing purposes or for functions related to the preparation and revision of drawings. The tools used for manual technical drawing have been displaced by the advent of computer-aided drawing, drafting and design (CADD).

Parchment craft The art of embellishing and decorating parchment paper

Parchment craft, also known as Pergamano, is the art of embellishing and decorating parchment paper through the use of techniques such as embossing, perforating, stippling, cutting and coloring.

Chemical milling or industrial etching is the subtractive manufacturing process of using baths of temperature-regulated etching chemicals to remove material to create an object with the desired shape. Other names for chemical etching include photo etching, chemical etching, photo chemical etching and photochemical machining. It is mostly used on metals, though other materials are increasingly important. It was developed from armor-decorating and printing etching processes developed during the Renaissance as alternatives to engraving on metal. The process essentially involves bathing the cutting areas in a corrosive chemical known as an etchant, which reacts with the material in the area to be cut and causes the solid material to be dissolved; inert substances known as maskants are used to protect specific areas of the material as resists.

Slot-die coating Coating technique for the application of solution, slurry, or extruded thin films onto typically flat substrates

Slot-die coating is a coating technique for the application of solution, slurry, or extruded thin films onto typically flat substrates such as glass, metal, paper, fabric or plastic foils. The process was first developed for the industrial production of photographic films in the 1950's. It has since become relevant in numerous commercial processes and nanomaterials related research fields.

References

Sources

Owen, Tim; Pilbeam, Elaine (1992). Ordnance Survey – Map Makers to Britain Since 1791. Southampton: Ordnance Survey. ISBN   0-31-900249-7.