St Croix Excelsior

Last updated

Excelsior
Role Ultralight aircraft
National origin United States
Manufacturer St Croix Aircraft
DesignerChad Wille and Charles Wille
First flight1980
StatusProduction completed
Produced1980-circa 2000

The St Croix Excelsior (English: ever higher) is an American ultralight aircraft that was designed by Chad Wille and Charles Wille, produced by St Croix Aircraft of Corning, Iowa and first flown in 1980. The aircraft was supplied in the form of plans for amateur construction with some hard-to-make parts available as well as partial kits. [1] [2] [3] [4]

Contents

Design and development

The Excelsior was designed to comply with the US FAR 103 Ultralight Vehicles rules, including the category's maximum empty weight of 254 lb (115 kg). The aircraft has a standard empty weight of 250 lb (113 kg). It features a strut-braced high-wing, a single-seat, open cockpit, tricycle landing gear and a single engine in pusher configuration. [2]

The aircraft fuselage is made from welded 4130 steel tubing, with the wings and tail built from riveted sheet aluminum, aluminum tubing and covered with doped aircraft fabric covering. Its straight leading edge, tapered trailing edge, 34.6 ft (10.5 m) span wing is braced with a single lift strut per side. The pilot sits in an open cockpit, with a small windshield. The engine and tail configuration are unconventional. The specified Zenoah G25 20 hp (15 kW) engine is mounted on top of the high wing and drives the tail-mounted propeller through a flexible extension shaft, that is designed to eliminate vibrations. The tailplane and elevator are mounted on top of the rear fuselage, with the fin and rudder mounted below the tailplane, providing protection for the propeller from contacting the ground. The controls are conventional, except that roll control is provided by spoilers, rather than ailerons. The landing gear consists of suspended main gear, a nose wheel and a rudder-mounted rear skid. [1] [2]

The aircraft has enough gliding performance to be soared. The construction time from the plans is estimated at 400 hours. Plans were intermittently available between 1980 and about 2000, but from 2001 the design was not advertised as being available by the company any longer. [2] [3] [5]

Specifications (Excelsior)

Data from Cliche, Kitplanes and Purdy [1] [2] [4]

General characteristics

Performance

Related Research Articles

The Adams CA-2 is a single seat, low-wing, American ultralight aircraft that was designed by Frank Griffith of Corning Aircraft around 1992 and was available as plans for amateur construction until 1999. In 1999, Hummel Aviation of Bryan, Ohio began offering the design. Although the design was well received, plans were no longer listed as being available from Hummel Aviation as of 2007.

Team Mini-Max Hi-MAX

The Team Mini-Max Hi-MAX is a single-seat, high wing, strut-braced, single engine aircraft available in kit form for amateur construction. It first flew in 1987 and is a high wing development of the Mini-MAX, hence its model name.

The Hy-Tek Hurricane 103 is a family of single-engined, high wing tricycle gear-equipped aircraft that were available in kit form from Hy-Tek Hurricane of Aurora, Oregon.

Kolb Firestar

The Kolb Firestar is a family of American open cockpit, high wing, pusher configuration, conventional landing gear-equipped ultralight aircraft that was produced in kit form by Kolb Aircraft of Phoenixville, Pennsylvania and intended for amateur construction.

Kolb Mark III

The Kolb Mark III is a family of American side-by-side two seater, high wing, strut-braced, pusher configuration, conventional landing gear-equipped ultralight aircraft that is produced in kit form by New Kolb Aircraft of London, Kentucky, and intended for amateur construction.

The Kolb Slingshot is an American tandem two seat, high wing, strut-braced, pusher configuration, conventional landing gear-equipped ultralight aircraft, that was produced in kit form by New Kolb Aircraft of London, Kentucky and intended for amateur construction.

The Kolb Kolbra and King Kolbra are a family of American tandem two seater, high wing, strut-braced, pusher configuration, conventional landing gear-equipped ultralight aircraft that are produced in kit form by New Kolb Aircraft of London, Kentucky and intended for amateur construction.

Milholland Legal Eagle American ultralight aircraft design

The Milholland Legal Eagle is an American high wing, strut-braced, single engine, tractor configuration, conventional landing gear-equipped ultralight aircraft that is available as plans from Better Half VW of Brookshire, Texas and also produced in kit form by J&N Bolding Enterprises of Baytown, Texas and intended for amateur construction.

The Wood Sky Pup is an American single-seat, high wing, cantilever, single engine, conventional landing gear ultralight aircraft that was designed by Stephen K. Wood of Whitewater, Colorado for amateur construction.

Carlson Sparrow

The Carlson Sparrow is a family of American, high wing, strut-braced, single engine, ultralight aircraft that was designed by Ernst W. Carlson and produced by Carlson Aircraft of East Palestine, Ohio and later Skyline Technologies of Salem, Ohio for amateur construction.

Bailey-Moyes Dragonfly

The Bailey-Moyes Dragonfly is an Australian-American two-seats-in-tandem, high-wing, strut-braced, open cockpit, conventional landing gear-equipped ultralight aircraft. The aircraft has been in production since 1990 and was designed as a special-purpose tug for hang gliders and ultralight sailplanes. It is available as a complete aircraft or as a kit for amateur construction. The aircraft has been variously produced by Moyes Microlights, Bailey-Moyes Microlights and currently LiteFlite of Botany, New South Wales, all different iterations of the same company.

The Precision Tech Fergy F-II B is a two-seat side-by-side, conventional landing gear, strut-braced, high-wing, pusher configuration ultralight aircraft that was manufactured by Ferguson Aircraft and later Precision Tech Aircraft in kit form for amateur construction. The aircraft is out of production and no longer available.

The Arnet Pereyra Sabre II is an American, two-seats in side-by-side configuration, conventional landing gear-equipped, strut-braced, high-wing ultralight trainer that was produced by Arnet Pereyra Inc of Rockledge, Florida in kit form for amateur construction.

The US Aviation Super Floater is an American high-wing, strut-braced, single-seat glider that was designed by Klaus Hill and Larry Hall and produced by US Aviation initially and later by Wind Walker Aircraft Co.

The US Aviation CAVU is an American high-wing, strut-braced, single-seat, open cockpit, single engine in pusher configuration, ultralight aircraft that was designed and produced by AeroDreams of Manchester, Tennessee, but marketed by US Aviation of St Paul, Minnesota under their brand name. The aircraft was supplied as a kit for amateur construction.

The Danieli Piuma is a family of Italian high-wing, strut-braced, pusher configuration single-seat motor gliders that was designed by Tiziano Danieli of Schio and supplied as plans for amateur construction.

The Bailey-Moyes Tempest, is an Australian-American high-wing, strut-braced, single-seat, microlift glider that was designed by Bob Bailey of Florida, United States and produced by Moyes Microlights of Waverley, New South Wales, Australia.

The Howland H-3 Pegasus is an American ultralight aircraft that was designed by Bert Howland and made available by Howland Aero Design in the form of plans for amateur construction, with kits provided by Aircraft Spruce & Specialty Co. The H-3 first flew in 1988.

The Norman Aviation Nordic II is a Canadian advanced ultralight aircraft, designed by Jacques Norman and produced by Norman Aviation of Saint-Anselme, Quebec, first flying in 1986. The aircraft is supplied as a kit for amateur construction or as a complete ready-to-fly-aircraft and remained in production through 2012.

The Phoenix Industries Sport is an American powered parachute that was designed and produced by Phoenix Industries of Southampton, New Jersey. Now out of production, when it was available the aircraft was supplied as in the form of plans for amateur construction. In addition to the plans the company also supplied materials kits and canopies.

References

  1. 1 2 3 Purdy, Don: AeroCrafter - Homebuilt Aircraft Sourcebook, page 247. BAI Communications. ISBN   0-9636409-4-1
  2. 1 2 3 4 5 Cliche, Andre: Ultralight Aircraft Shopper's Guide 8th Edition, page E-15. Cybair Limited Publishing, 2001. ISBN   0-9680628-1-4
  3. 1 2 Virtual Ultralight Museum (n.d.). "Excelsior" . Retrieved November 10, 2011.
  4. 1 2 Downey, Julia: 1999 Plans Aircraft Directory, Kitplanes, Volume 16, Number 1, January 1999, page 67. Primedia Publications. ISSN 0891-1851
  5. ↑ Downey, Julia: 2001 Plans Aircraft Directory, Kitplanes, Volume 18, Number 1, January 2001, page 28. Kitplanes Acquisition Company. ISSN 0891-1851
This page is based on this Wikipedia article
Text is available under the CC BY-SA 4.0 license; additional terms may apply.
Images, videos and audio are available under their respective licenses.