Tin ceiling

Last updated
Pressed tin ceiling over a store entrance in Bellingham, Washington, U.S.A. B'ham Fairhaven - Art Glass store - tin ceiling.jpg
Pressed tin ceiling over a store entrance in Bellingham, Washington, U.S.A.

A tin ceiling is an architectural element, consisting of a ceiling finished with plates of tin with designs pressed into them, that was very popular in Victorian buildings in North America in the late 19th and early 20th century. [1] They were also popular in Australia where they were commonly known as pressed metal ceilings or Wunderlich ceilings (after the main Australian manufacturer Wunderlich). [2] They were also used in South Africa. [3]



Tin ceilings were introduced to North America as an affordable alternative to the exquisite plasterwork used in European homes. They gained popularity in the late 1800s as Americans sought sophisticated interior design. Durable and lightweight, tin ceilings were appealing to home and business owners alike as a functionally attractive design element that was readily available. Important critics such as John Ruskin, George Gilbert Scott, Charles Eastlake and William Morris debated the implications of faux materials. These critics believed it was morally wrong and deceptive to imitate another material and blamed the degradation of society towards the "art of shamming" rather than honesty in architecture. [4] Nevertheless, tin ceilings lasted longer than plaster ones and were easier to clean. They encapsulated ideas of democracy, making such decoration available to the middle class majority who supported the machine production.

Decorative metal ceilings were first made of corrugated iron sheets, appearing in the United States by the early 1870s. [5] It was during the late Victorian era that thin rolled tin-plate was being mass-produced. Tinplate was originally made from dipping iron in molten tin in order to prevent rust. Later, steel replaced iron as the more cost-effective solution. Tinplate was not the only sheet metal used to make stamped ceilings. Copper, lead (known as ternplate) and zinc were other common architectural metals in the industry.

Between 1890 and 1930, approximately forty-five companies in the United States marketed metal ceilings; most were in Ohio, Pennsylvania, and New York, located along railroad lines that served as the main routes for delivering the pressed metal products directly to contractors. The Wheeling Corrugating Company out of Wheeling, West Virginia, became the leading tin ceiling manufacturer in the late 1800s. At that time, Wheeling Corrugating was a large steel mill that also made products from their steel sheets such as roofing and siding. [6]

Sheets of tin were stamped one at a time using rope drop hammers and cast iron molds. Using this method of production, metal was sandwiched between two interlocking tools. The top tool, or "ram," was lifted up by a rope or chain, then dropped down onto the bottom die, smashing into the metal that was underneath and permanently embedding intricate patterns into the tin. Someone who saw the merit of this modern machine for its artistic potential was Frank Lloyd Wright. In his articles, "The Art and Craft of the Machine" and "In the Cause of Architecture," the series published by Architectural Record, Wright elaborates on his modern theory of science and art and the role of the machine in the future of art.

Tin ceiling in a private music room, Queensland, Australia, 1906 StateLibQld 1 15930 Music room in a private home, 1906.jpg
Tin ceiling in a private music room, Queensland, Australia, 1906

Tin ceilings were traditionally painted white to give the appearance of hand-carved or molded plaster. They were incorporated into residential living rooms and parlors as well as schools, hospitals and commercial businesses where painted tin was often used as wainscoting.

In the 1930s, tin ceilings began to lose their popularity and steel materials became scarce because of the effort to collect scrap metal during WWII. Many sheet metal companies began making other products in order to stay in business. In the 21st century, some renewed interest has been shown in tin ceilings. The increase in interest has stemmed from businesses that were renovating and an interest to return to the nostalgia of the turn of the century. Still to this day there exists a manufacturing company by the name of W.F. Norman Corporation that produces original tin ceilings and ornaments from the same rope drop hammers as it once did in 1898. [7] Several other companies offer conventional tin ceilings as well as panels made to fit into a drop-ceiling grid.


Tin ceilings were built to last, and in the absence of prolonged moisture damage leading to corrosion, they usually did; however, the wear and tear over the hundred years since the heyday of tin has led to a burgeoning restoration industry. Magazines such as The Old-House Journal were created to offer articles about restoration, repair and installation practices for historic preservation of tin ceilings.

Environmental hazards from the lead paint used on turn of the century tin ceilings mean that this is a job for experts in the field. Often restoration is achieved by simply stripping old paint, treating the metal with a protective base coat, patching minor damaged areas, and repainting. In some cases, where small sections of a ceiling have been damaged, partial restoration is needed. Panels can be easily replaced through companies that still manufacture original design components. If, however, a ceiling requires a historic pattern that is no longer in production, good quality panels from the existing ceiling may be used to create a mold and new customized tin can be pressed.

If full restoration is needed, meaning no part of the existing ceiling remains structurally sound, a professional can help design a new ceiling appropriate for the period and structure using existing molds or creating reproductions based on photographic evidence or architectural drawings. This latter method can be extremely expensive, and is not cost effective, due to the cost of making a custom mold for the panel and usually the metal trim that was also used with the original project.

More detailed information for repair and replacement of decorative metal ceilings can be found in the National Park Service Technical Preservation Services.

Modern adaptation

Several companies now offer hand-painted finishes for metalwork, as well as a more permanent look that can be achieved with powder-coated finishes. For the low end of the market, imitation panels are pressed from plastic or aluminum. Tin is now fashionably used for art work, back splashes, cabinet faces, wainscoting and much more. For over 100 years the tin panel was made with nail rails around the outside of the panel, designed to overlap each other. Panels were nailed into wood furring strips which were prevalent prior to the invention of plywood. Today, nail up panels can be easily brad nailed or hand nailed, into plywood without the need for the original 1-by-2-inch (25 mm × 51 mm) furring strips. There is also a patented interlocking tin panel that will screw directly into existing drywall/popcorn/plaster ceilings, without the need for extensive plywood installation. Tin panels today are made in 24-by-24-inch (610 mm × 610 mm) and 24-by-48-inch (610 mm × 1,220 mm) sizes for easier handling and one-person installation. Today, most tin ceiling manufacturers actually use recycled blackplate steel in a thickness of only 0.010 inches (0.25 mm). There are some manufacturers who also use actual tin plated steel, which is simply the blackplate steel with a thin coating of bright tin plate adhered to the base metal. Other manufacturers utilize aluminum, as it is rustproof and will last a lifetime.

This finish is also an option with dropped ceilings.

Related Research Articles

<span class="mw-page-title-main">Drywall</span> Panel made of gypsum, used in interior construction

Drywall is a panel made of calcium sulfate dihydrate (gypsum), with or without additives, typically extruded between thick sheets of facer and backer paper, used in the construction of interior walls and ceilings. The plaster is mixed with fiber ; plasticizer, foaming agent; and additives that can reduce mildew, flammability, and water absorption.

<span class="mw-page-title-main">Stucco</span> Construction material made of aggregates, a binder, and water

Stucco or render is a construction material made of aggregates, a binder, and water. Stucco is applied wet and hardens to a very dense solid. It is used as a decorative coating for walls and ceilings, exterior walls, and as a sculptural and artistic material in architecture. Stucco can be applied on construction materials such as metal, expanded metal lath, concrete, cinder block, or clay brick and adobe for decorative and structural purposes.

<span class="mw-page-title-main">Structural insulated panel</span>

A structural insulated panel, or structural insulating panel, (SIP), is a form of sandwich panel used in the construction industry.

<span class="mw-page-title-main">Siding (construction)</span> Exterior cladding on building walls

Siding or wall cladding is the protective material attached to the exterior side of a wall of a house or other building. Along with the roof, it forms the first line of defense against the elements, most importantly sun, rain/snow, heat and cold, thus creating a stable, more comfortable environment on the interior side. The siding material and style also can enhance or detract from the building's beauty. There is a wide and expanding variety of materials to side with, both natural and artificial, each with its own benefits and drawbacks. Masonry walls as such do not require siding, but any wall can be sided. Walls that are internally framed, whether with wood, or steel I-beams, however, must always be sided.

<span class="mw-page-title-main">Corrugated galvanised iron</span> Type of metal building material

Corrugated galvanised iron or steel, colloquially corrugated iron, wriggly tin, pailing, corrugated sheet metal, or just tin (Australia) and occasionally abbreviated CGI is a building material composed of sheets of hot-dip galvanised mild steel, cold-rolled to produce a linear ridged pattern in them. Although it is still popularly called "iron" in the UK, the material used is actually steel, and only the surviving vintage sheets may actually be made up of 100% iron. The corrugations increase the bending strength of the sheet in the direction perpendicular to the corrugations, but not parallel to them, because the steel must be stretched to bend perpendicular to the corrugations. Normally each sheet is manufactured longer in its strong direction.

<span class="mw-page-title-main">Lath and plaster</span> Finish mainly for interior dividing walls and ceilings

Lath and plaster is a building process used to finish mainly interior dividing walls and ceilings. It consists of narrow strips of wood (laths) which are nailed horizontally across the wall studs or ceiling joists and then coated in plaster. The technique derives from an earlier, more primitive process called wattle and daub.

<span class="mw-page-title-main">Sheet metal</span> Metal formed into thin, flat pieces

Sheet metal is metal formed into thin, flat pieces, usually by an industrial process. Sheet metal is one of the fundamental forms used in metalworking, and it can be cut and bent into a variety of shapes.

<span class="mw-page-title-main">Framing (construction)</span> Construction technique

Framing, in construction, is the fitting together of pieces to give a structure support and shape. Framing materials are usually wood, engineered wood, or structural steel. The alternative to framed construction is generally called mass wall construction, where horizontal layers of stacked materials such as log building, masonry, rammed earth, adobe, etc. are used without framing.

<span class="mw-page-title-main">Kitchen cabinet</span> Kitchen furniture

Kitchen cabinets are the built-in furniture installed in many kitchens for storage of food, cooking equipment, and often silverware and dishes for table service. Appliances such as refrigerators, dishwashers, and ovens are often integrated into kitchen cabinetry. There are many options for cabinets available at present.

<span class="mw-page-title-main">Dropped ceiling</span> Secondary ceiling hung below a main ceiling

A dropped ceiling is a secondary ceiling, hung below the main (structural) ceiling. It may also be referred to as a drop ceiling, T-bar ceiling, false ceiling, suspended ceiling, grid ceiling, drop in ceiling, drop out ceiling, or ceiling tiles and is a staple of modern construction and architecture in both residential and commercial applications.

<span class="mw-page-title-main">Tinning</span> Covering object with layer of tin

Tinning is the process of thinly coating sheets of wrought iron or steel with tin, and the resulting product is known as tinplate. The term is also widely used for the different process of coating a metal with solder before soldering.

<span class="mw-page-title-main">Plasterwork</span> Construction or ornamentation done in plaster or a similar material

Plasterwork is construction or ornamentation done with plaster, such as a layer of plaster on an interior or exterior wall structure, or plaster decorative moldings on ceilings or walls. This is also sometimes called pargeting. The process of creating plasterwork, called plastering or rendering, has been used in building construction for centuries. For the art history of three-dimensional plaster, see stucco.

Wheeling-Pittsburgh Steel was a steel manufacturer based in Wheeling, West Virginia.

<span class="mw-page-title-main">Metal roof</span>

A metal roof is a roofing system featuring metal pieces or tiles exhibiting corrosion resistance, impermeability to water, and long life. It is a component of the building envelope. The metal pieces may be a covering on a structural, non-waterproof roof, or they could be self-supporting sheets.

Homasote is a brand name associated with the product generically known as cellulose-based fiber wall board, which is similar in composition to papier-mâché, made from recycled paper that is compressed under high temperature and pressure. Homasote contains no adhesives. It is held together by the surface tension between the paper fibers, a process that is augmented by hydrogen bonding and the presence of a wax binder. It is available in multiple thicknesses and comes in sheets 4 by 8 feet. The Homasote Company operates a 750,000-square-foot (70,000 m2) factory in the West Trenton section of Ewing Township, New Jersey.

<span class="mw-page-title-main">Architectural metals</span>

Metals used for architectural purposes include lead, for water pipes, roofing, and windows; tin, formed into tinplate; zinc, copper and aluminium, in a range of applications including roofing and decoration; and iron, which has structural and other uses in the form of cast iron or wrought iron, or made into steel. Metal alloys used in building include bronze ; brass ; monel metal and nickel silver, mainly consisting of nickel and copper; and stainless steel, with important components of nickel and chromium.

Perforated metal, also known as perforated sheet, perforated plate, or perforated screen, is sheet metal that has been manually or mechanically stamped or punched using CNC technology or in some cases laser cutting to create different holes sizes, shapes and patterns. Materials used to manufacture perforated metal sheets include stainless steel, cold rolled steel, galvanized steel, brass, aluminum, tinplate, copper, Monel, Inconel, titanium, plastic, and more.

<span class="mw-page-title-main">Tin toy</span>

A tin toy, or tin lithograph toy, is a mechanical toy made out of tinplate and colorfully painted by chromolithography to resemble primarily a character or vehicle.

<span class="mw-page-title-main">St Brigid's Church, Rosewood</span> Historic site in Queensland, Australia

St Brigids Catholic Church is a heritage-listed Roman Catholic church at 11 Railway Street, Rosewood, City of Ipswich, Queensland, Australia. It was designed by Reverend Andrew Horan and built in 1909 by RJ Murphy with alterations in 1935. It was added to the Queensland Heritage Register on 21 October 1992.

<span class="mw-page-title-main">L. Lewis Sagendorph</span>

L. Lewis Sagendorph was an American inventor and leading manufacturer of sheet metal products in the late 19th and very early 20th centuries. He founded what later became the Penn Metal Company in Philadelphia, Pennsylvania.


  1. "Shoptalk: Pressed Tin Ceiling". Treanor Architects. Retrieved 2015-09-18.
  2. "History - Wunderlite Reproduction Panels". www.wunderlite.com.au. Retrieved 2015-10-06.
  3. "History of tin ceilings" . Retrieved 6 October 2015.
  4. Simpson, Pamela H. (1999). Cheap, Quick, & Easy: Imitative Architectural Materials 1870-1930. Knoxville: University of Tennessee Press. pp. 136–144. ISBN   978-1-62190-157-0.
  5. Staveteig, Kaaren R. "Historic Decorative Metal Ceilings and Walls: Use, Repair, and Replacement" (PDF). Preservation Briefs (49). Retrieved March 18, 2019.
  6. "The Legacy of W.F. Norman — W.F. Norman Corp". wfnorman.com. Retrieved 2017-03-04.
  7. "W.F. Norman Corp. – Hand Pressed Tin Ceilings – Tin Ceiling Panels, Cornices, Tin Ceiling Designs, Roofing, Siding, and Ornaments". wfnorman.com. Retrieved 2017-03-04.