 |
The two-stroke power valve system is an improvement to a conventional two-stroke engine that gives a high power output over a wider RPM range.
| |
The two-stroke power valve system is an improvement to a conventional two-stroke engine that gives a high power output over a wider RPM range.
A stroke is the action of a piston travelling the full length of its cylinder. In a two-stroke engine, one of the two strokes combines the intake stroke and the compression stroke, while the other stroke combines the combustion stroke and the exhaust stroke.
As the piston travels upward in the cylinder, it creates low pressure area in the crankcase; this draws fresh air and atomized fuel from the carburetor through a hole in the cylinder wall or directly into the crankcase. As the piston continues travelling upward, transfer ports and the exhaust ports are closed off, thus trapping the combustible mixture in the combustion chamber. As the piston reaches the top of the cylinder, the mixture in the cylinder is compressed to the point of ignition.
The second stroke begins once ignition has taken place. The power stroke begins after the air-fuel mixture is ignited. The burnt fuel creates pressure in the cylinder above the piston and forces it downward. As the piston passes the midpoint of the downstroke, the exhaust port to the side of the cylinder is uncovered and initiates the flow of burned fuel into the expansion chamber or muffler.
The piston then moves downward, where the air-fuel mixture remains from the previous intake-compression stroke. Shortly after the exhaust port is uncovered by the downward travel of the piston, the transfer ports begin to be uncovered. The transfer ports act as a passage through which the air-fuel mixture moves from the crankcase into the cylinder above the piston. Once the piston reaches the bottom of the stroke, the second stroke is completed and the process is repeated.
The only moving parts inside simple two-stroke engines are the crankshaft, the connecting rod, and the piston. It is the same simplicity in design, however, that causes a two-stroke engine to be less fuel-efficient and produce high specific levels of undesirable exhaust gas emissions. At the bottom of the power stroke, the transfer ports, which deliver fresh fuel-air mixture, are open at the same time as the exhaust port. This can allow a significant amount of fresh fuel to run straight through the engine without being burned in the process of power production. Properly designed exhaust systems help minimize the amount of raw fuel loss in the exhaust process, but a carbureted two-stroke engine will always waste some fuel (modern direct injected engines avoid this).
Many producers of two-stroke performance bikes fit them with the exhaust power valve systems. These valves act to vary the height (and width) of the exhaust port thereby broadening power delivery over a wider rev range. Exhaust ports with fixed dimensions only produce usable power in a narrow rev range, which also affects fuel consumption and emissions.
In a race bike, this is not a problem as the engine will be operating at high RPM almost all the time. However, in a road/commuter bike, the limited power range is a problem. To provide more low RPM power, as well as enable the engine to produce a lot of high RPM power, a power valve system is used.
All power valve systems vary the duration of the exhaust port open time, which gives the engine usable low end power combined with excellent top end power. Manufacturers have also included sub exhaust chambers that extend the 'tuned length' of the expansion chamber.
Power valve actuation can be by mechanical (RPM dependent) or electric (servo motor) means increasingly with electronic control. Electronic control offers a greater degree of accuracy as well as being able to vary the opening of the valve and be tuned to conditions.
AETC and Super AETC Suzuki engines, Automatic Exhaust Timing Control: The two-blade version was fitted to the VJ21 RGV250, and the three-blade version, to the VJ22 RGV250 and Suzuki RG150.
With the AETC system, the power-valve systems are normally partially closed at low RPM; when closed, it enables the engine to make more power. Up to a certain point, however, power drops off as the engine is unable to expel enough gases out of the exhaust. When the power-valve is opened, it allows more gases to flow out of the exhaust port. This system is recognizable by a small box above the exhaust outlet; the power-valves are situated in this box. Depending on the valve, they may be made of two (older version) or three (newer version) separate blades.
YPVS Yamaha engines, Yamaha Power Valve System: Yamaha engineers realized that by altering the height of the exhaust port they could effectively change the engine power delivery thereby having optimal power and torque across the entire rev range, so it was that the YPVS was born. The valve is of a cylindrical "cotton reel" design running across the top of the exhaust port, it is turned by a servo motor controlled from a control box taking information from the CDI (and other locations). The valve is a slightly oval shape. This changes the height and size of the exhaust port at different engine speeds, maximizing the available power at all rev ranges, opening up firstly at 3k rpm for low end power, gradually in between 3-6k, fully opening at 6k rpm for maximum power, on most 125cc. It was fitted to all of the later models of the RZ/RD two-stroke road bikes (125, 250, 350 and 500 cc), the TZR range. It was also added to the DT(125lc 2/3) range after 1984 (but was locked closed to comply with UK learner regulations until the (R) in 1988-04 which had a fully functional YPVS valve) the DT125R has a better design of engine, although not much altered in speed, just more reliable than its predecessor. The YZ series of motocross bikes has a mechanical power valve which is activated at RPM speed. The YPVS is only found on the liquid-cooled bikes not air cooled versions. Yamaha have also used a guillotine version in some of their later models such as the 1994 TZR250 3XV SP model, and many later TZ road race bikes. The TZR250R 3XV SPR actually uses a Triple-YPVS, which is a combination of the guillotine and "cotton reel" designs.
Yamaha was actually the first company to produce consistent results with their YPVS in their race bikes. The 1977 OW35K was the first race bike to incorporate the power valve system and it won the Finnish GP in 1977. The Kadenacy effect was harnessed and controlled to a point that gave Yamaha great advantage over all the other manufacturers throughout the late '70s and into the mid '80s. The first street bikes with YPVS were the RZ/RD350 YPVS (LC2-onwards), and RZ/RD500 GP Replica in 1983–84.
ATAC System: The Honda Automatic Torque Amplification Chamber system works by effectively increasing or decreasing the volume of the exhaust system with a small butterfly valve located just before the exhaust connection. At low RPM a centrifugal crankshaft driven gear opens the valve into a small chamber and increases the volume of the exhaust by allowing the exhaust gases to flow through the chamber. At high RPM the ATAC valve is closed and the exhaust simply exits into the expansion chamber. A larger expansion chamber allows for more power at lower RPMs because of the extra time needed for the impulse to "bounce" back for the supercharger effect. It was used on their CR motocrossers, GP bikes and MTX, MVX, NS and NSR road bikes.
HPP valve. A centrifugal governor opens and closes a two-blade exhaust valve (using over 50 parts)
The "V-TACS" - Variable Torque Amplification Chamber System - works differently from the "ATAC system" and it will only work when it is used in conjunction with a tuned muffler. Tuned mufflers/expansion chambers increase power but only at the RPM they are designed for and can actually cause a power loss outside their tuned RPM. "V-TACS system" takes advantage of using an expansion chamber without losing power outside the expansion chamber's tuned RPM. Within the head and cylinder of the engine, there is a chamber that is sealed by a valve. This sealed chamber is vented onto the exhaust port when the valve is open. At low RPM this valve is open, this has the effect of increasing the exhaust manifold volume and negating the power loss that would normally be apparent at low RPM with an expansion chamber. At mid RPM the valve is closed, this enables the expansion chamber to work. It is identified by the head and cylinder, being much larger than normal for its displacement, the cylinder wall is also cast with the wording VTACS on it.
V-TACS was a foot-operated power valve system made by Honda on some of its small two-stroke bikes and scooters, like the Honda FC50.
The Honda Revolution Control valve is designed and works in principle like the "AETC system." A small computer monitors engine RPM and adjusts a two-blade exhaust valve with an electric servo. Honda equipped many two-stroke motorcycles such as the NSR125 and NSR250 models with RC - Valve power plants.
Kawasaki uses a power-valve system called KIPS (Kawasaki Integrated Power Valve System) on their two-stroke bikes. The KIPS utilizes both alterations in port height, closing of the secondary port ducting, and a resonant chamber. KIPS is operated by a mechanical governor on single cylinder machines. The twin cylinder and newer single cylinder model bikes have an electric motor transferring movement via cable and linkages called HI-KIPS.
A two-strokeengine is a type of internal combustion engine that completes a power cycle with two strokes of the piston during one power cycle, this power cycle being completed in one revolution of the crankshaft. A four-stroke engine requires four strokes of the piston to complete a power cycle during two crankshaft revolutions. In a two-stroke engine, the end of the combustion stroke and the beginning of the compression stroke happen simultaneously, with the intake and exhaust functions occurring at the same time.
A four-strokeengine is an internal combustion (IC) engine in which the piston completes four separate strokes while turning the crankshaft. A stroke refers to the full travel of the piston along the cylinder, in either direction. The four separate strokes are termed:
VTEC is a system developed by Honda to improve the volumetric efficiency of a four-stroke internal combustion engine, resulting in higher performance at high RPM, and lower fuel consumption at low RPM. The VTEC system uses two camshaft profiles and hydraulically selects between profiles. It was invented by Honda engineer Ikuo Kajitani. It is distinctly different from standard VVT systems which change only the valve timings and do not change the camshaft profile or valve lift in any way.
The Honda XR series is a range of four-stroke off-road motorcycles that were designed in Japan but assembled all over the world.
In automotive engineering, an exhaust manifold collects the exhaust gases from multiple cylinders into one pipe. The word manifold comes from the Old English word manigfeald and refers to the folding together of multiple inputs and outputs.
An inlet manifold or intake manifold is the part of an internal combustion engine that supplies the fuel/air mixture to the cylinders. The word manifold comes from the Old English word manigfeald and refers to the multiplying of one (pipe) into many.
Reed valves are a type of check valve which restrict the flow of fluids to a single direction, opening and closing under changing pressure on each face. Modern versions often consist of flexible metal or composite materials.
The Honda F-Series engine was considered Honda's "big block" SOHC inline four, though lower production DOHC versions of the F-series were built. It features a solid iron or aluminum open deck cast iron sleeved block and aluminum/magnesium cylinder head.
A motorcycle engine is an engine that powers a motorcycle. Motorcycle engines are typically two-stroke or four-stroke internal combustion engines, but other engine types, such as Wankels and electric motors, have been used.
The Yamaha RZ350 is a two-stroke motorcycle produced by Japanese motorcycle manufacturer Yamaha between 1983 and 1996. Available in the US from 1983-1985, Canada until 1990 and Brazil until 1996. The RZ was the final evolution of the popular and well-known series of RD Yamaha motorcycles, and as such is also known as the RD350LC II or RD350 YPVS.
Back pressure is the term for a resistance to the desired flow of fluid through pipes. Obstructions or tight bends create backpressure via friction loss and pressure drop.
Cylinder head porting refers to the process of modifying the intake and exhaust ports of an internal combustion engine to improve their air flow. Cylinder heads, as manufactured, are usually suboptimal for racing applications due to being designed for maximum durability. Ports can be modified for maximum power, minimum fuel consumption, or a combination of the two, and the power delivery characteristics can be changed to suit a particular application.
The Yamaha DT200 is a dual-purpose motorcycle manufactured during the 1980s, 1990s, and continues into the 2000s (decade) by the Yamaha Motor Company. Though never imported into the US, the rest of the world, including Canada, received some of these models. The DT200LC began production in 1983bc. It also was very similar to the DT125LC. This model continued production until 1988.Then, in 1989 a totally new model was introduced, DT200R (3ET), as well as a similar DT125R. In Canada, the DT125LC/R was never imported.
The Yamaha TZR250 is a motorcycle manufactured and produced by the Japanese motorcycle manufacturer Yamaha between 1986 and 1995.
In a spark ignition internal combustion engine, ignition timing is the timing, relative to the current piston position and crankshaft angle, of the release of a spark in the combustion chamber near the end of the compression stroke.
The Yamaha RD500LC is a high-performance, two-stroke sports motorcycle, also known as the RZ500 in Canada and Australia. A lightened but detuned version known as the RZV500R was developed for the Japanese home market. Strict United States Environmental Protection Agency regulations meant that the RZ500 was not available for sale in that country. Produced for a short period between 1984 and 1986 it has become a sought after collector's machine.
The Honda CB400 Super Four is a CB series 399 cc (24.3 cu in) standard motorcycle produced by Honda at the Kumamoto plant from 1992 to the present. The CB400 embodies the typical Universal Japanese Motorcycle produced through the 1970s, updated with modern technology. To this end, the bike has a naked retro design, paired with a smooth inline-four engine. Originally a Japan-only bike, it was later also available in SE Asia, and from 2008 in Australia.
In an internal combustion engine, the geometry of the exhaust system can be optimised ("tuned") to maximise the power output of the engine. Tuned exhausts are designed so that reflected pressure waves arrive at the exhaust port at a particular time in the combustion cycle.
An internal combustion engine is a heat engine in which the combustion of a fuel occurs with an oxidizer in a combustion chamber that is an integral part of the working fluid flow circuit. In an internal combustion engine, the expansion of the high-temperature and high-pressure gases produced by combustion applies direct force to some component of the engine. The force is typically applied to pistons, turbine blades, a rotor, or a nozzle. This force moves the component over a distance, transforming chemical energy into kinetic energy which is used to propel, move or power whatever the engine is attached to.
The Suzuki A100 is a Japanese motorcycle from the Suzuki Motor Corporation with production starting in 1966.Similar models were produced by Yamaha and Kawasaki with the YB100 & KH100 models, also with a single-cylinder two-stroke engine and rotary valve being examples.