Waspair HM 81 Tomcat

Last updated

HM 81 Tomcat
Role Ultralight aircraft
National origin United Kingdom
Manufacturer Waspair
Midwest Microlites
First flight1980
StatusProduction completed

The Waspair HM 81 Tomcat is a British canard ultralight aircraft of unusual design, that was produced by Waspair and later Midwest Microlites. The designer is disputed and Chip Erwin, Larry Whiting and Robin Haynes are all named as designers. The aircraft was supplied as a kit for amateur construction. [1] [2]

Contents

Design and development

The aircraft was designed to comply with the US FAR 103 Ultralight Vehicles rules, including the category's maximum empty weight of 254 lb (115 kg). The aircraft has a standard empty weight of 248 lb (112 kg). It features a high-wing supported by dihedral stabilizers, a single-seat, open cockpit, tricycle landing gear and a single engine in pusher configuration. [1] [2]

The aircraft structure is made from aluminum tubing. Its 30 ft (9.1 m) span wing sits high above the pilot's seat, providing pendulum stability. The controls are very unconventional and all are canard mounted, which has two surfaces. The canard surfaces move in unison to produce pitch and separately, in opposite directions, to produce roll. The large fixed dihedral stabilizers provide yaw control as the wing has no dihedral of its own for yaw coupling. The canard surfaces are mounted to the front of the main keel tube, which serves as a fuselage. The pilot is accommodated on an open seat bolted to the same tube. The Cuyuna 430 powerplant is located behind the pilot. [1] [2]

In service the control system has proved inadequate and the aircraft is difficult to control in flight, particularly in air that is not smooth and there have been a number of loss-of-control accidents. The Virtual Ultralight Museum describes the aircraft as "ungainly and unstable". Reviewer Andre Cliche says of the Tomcat's handling characteristics: [1] [2]

It uses a 2-axis control system in which the canard controls pitch and roll. There is no rudder to control yaw but the V-wing is supposed to provide yaw stability. This is a deficient system with problems especially in yaw. Any kind of upset initiated by the pilot or by turbulence could impart a sideways motion that the rudder effect of the V-wing is not strong enough to counteract. The pilot must deflect the canard surface in the opposite direction before the upset pushes the nose beyond the maximum recovery angle of the canard. If this is not done, the result could be a non-controllable spiral dive. [1]

Cliche recommends that Tomcats be scrapped for parts and not flown. [1]

An improved model, the Pintail, was later introduced by Haynes, which has control surfaces on the trailing edge of the dihedral stabilizers, but it is unclear if this fully addresses the original design's deficiencies. [1]

Variants

Tomcat Standard
Initial version with two-axis controls [1] [2]
Tomcat Sport
Improved version with two-axis controls [2]
Tomcat Tourer
Two seat model with two-axis controls [2]
Haynes Pintail
Improved version with three-axis controls [1] [2]

Specifications (Pintail)

Data from Cliche [1]

General characteristics

Performance

Related Research Articles

Eipper Quicksilver

Quicksilver is a line of single and two-place high wing, single-engine, ultralight aircraft that evolved from weight-shift hang gliders including Bob Lovejoy's High Tailer.

The Birdman Atlas is a single-seat, high wing, single engine in pusher configuration, ultralight aircraft that was based upon the Eipper Quicksilver design.

The Kolb Ultrastar is an American single seat, high wing, strut-braced, single engine, pusher configuration, conventional landing gear-equipped ultralight aircraft that was produced in kit form by Kolb Aircraft of Phoenixville, Pennsylvania and intended for amateur construction.

The Airborne Avenger is an American ultralight aircraft that was designed and produced by Airborne Wing Design in the early 1980s. The aircraft was supplied as a kit for amateur construction.

The Robertson B1-RD is an American ultralight aircraft that was designed by Glen Bashforth and Bruce Bashforth and produced by the Robertson Aircraft Corporation. The aircraft was supplied as a kit for amateur construction with production starting in June 1982.

The International Ultralight Banchee is an American ultralight aircraft designed by Brian Jensen, Gil Kinzie and Nick Nichols and produced by International Ultralight Aviation. The aircraft was supplied as a kit for amateur construction.

The Hovey Delta Bird is an American ultralight aircraft that was designed by Bob Hovey in 1982 and supplied as plans for amateur construction.

The American Aerolights Eagle is an American ultralight aircraft that was produced by American Aerolights, introduced in 1975. The aircraft was supplied as a kit for amateur construction.

The Goldwing Ltd Goldwing is an American ultralight aircraft that was designed by Craig Catto and Brian Glenn and produced by Goldwing Ltd. The aircraft was supplied as a complete factory-built aircraft only and no kits or plans were offered.

The Advanced Aviation Husky, Hi-Nuski and Coyote are a family of American ultralight aircraft that was designed and produced by Advanced Aviation. The aircraft was supplied as a kit for amateur construction and introduced in 1978.

Cascade Kasperwing I-80 American ultralight airplane

The Cascade Kasperwing I-80 is an American ultralight flying wing motorglider that was designed by Witold Kasper and Steve Grossruck. It was produced by Cascade Ultralites and introduced in 1976. The aircraft was supplied as a kit for amateur construction.

The Manta Foxbat is an American ultralight aircraft that was designed by Bill Armour and produced by Manta Products Inc of Oakland, California. The aircraft was supplied as a kit for amateur construction.

The Paup P-Craft is an American ultralight aircraft that was designed by D. Paup and produced by Paup Aircraft, introduced in 1982. The aircraft was supplied as a kit for amateur construction.

The Rotec Rally is a family of American ultralight aircraft that was designed by Bill Adaska in 1977 and produced by Rotec Engineering of Duncanville, Texas. Adaska had been an aeronautical engineer at Bell Helicopter and the French helicopter manufacturer, Aerospatiale, prior to starting Rotec. The aircraft was supplied as a kit for amateur construction.

The Eastern Ultralights Snoop is a family of American ultralight aircraft that was designed by Bob Able and produced by Eastern Ultralights, starting in 1981. The aircraft was supplied as a kit for amateur construction.

The Swallow Aeroplane Company Swallow is a series of American ultralight aircraft that was designed by Chet Fudge and produced by the Swallow Aeroplane Company in the 1980s. The aircraft was supplied as a kit for amateur construction.

The Thor T/A is a Canadian ultralight aircraft that was designed by Thorsten B. Strenger and produced by Thor Air of Weston, Ontario. The aircraft was supplied as a kit for amateur construction.

The Pinaire Ultra-Aire is an American ultralight aircraft that was designed and produced by Pinaire Engineering. The aircraft was supplied as a kit for amateur construction.

The Chotia Woodhopper is an American ultralight aircraft that was designed by John Chotia and made available in the form of plans for amateur construction. The plans remain available from the Vintage Ultralight and Lightplane Association.

The Diehl AeroNautical XTC Hydrolight is an American amphibious flying boat ultralight aircraft that was designed and produced by Diehl AeroNautical in the 1980s.

References

  1. 1 2 3 4 5 6 7 8 9 10 Cliche, Andre: Ultralight Aircraft Shopper's Guide 8th Edition, page E-28 and E-41. Cybair Limited Publishing, 2001. ISBN   0-9680628-1-4
  2. 1 2 3 4 5 6 7 8 Virtual Ultralight Museum (n.d.). "Tomcat H.M. 81" . Retrieved 7 December 2011.