Widlar current source

Diagram from Widlar's original patent

A Widlar current source is a modification of the basic two-transistor current mirror that incorporates an emitter degeneration resistor for only the output transistor, enabling the current source to generate low currents using only moderate resistor values. ^{[1] [2] [3]}

The Widlar circuit may be used with bipolar transistors, MOS transistors, and even vacuum tubes. An example application is the 741 operational amplifier, ^[4] and Widlar used the circuit as a part in many designs. ^[5]

This circuit is named after its inventor, Bob Widlar, and was patented in 1967. ^{[6] [7]}

DC analysis

Figure 1: A version of the Widlar current source using bipolar transistors.

Figure 1 is an example Widlar current source using bipolar transistors, where the emitter resistance R₂ is connected to the output transistor Q₂, and has the effect of reducing the current in Q₂ relative to Q₁. The key to this circuit is that the voltage drop across the resistance R₂ subtracts from the base-emitter voltage of transistor Q₂, thereby turning this transistor off compared to transistor Q₁. This observation is expressed by equating the base voltage expressions found on either side of the circuit in Figure 1 as:

${\displaystyle {\begin{aligned}&V_{\text{B}}=V_{\text{BE1}}=V_{\text{BE2}}+(\beta _{2}+1)I_{\text{B2}}R_{2}\\\Rightarrow {}&{\frac {1}{R_{2}}}\left(V_{\text{BE1}}-V_{\text{BE2}}\right)=(\beta _{2}+1)I_{\text{B2}}\ ,\end{aligned}}}$

where β₂ is the beta-value of the output transistor, which is not the same as that of the input transistor, in part because the currents in the two transistors are very different. ^[8] The variable I_B2 is the base current of the output transistor, V_BE refers to base-emitter voltage. This equation implies (using the Shockley diode equation):

Eq. 1

${\displaystyle {\begin{aligned}(\beta _{2}+1)I_{\text{B2}}&=\left(1+{\frac {1}{\beta _{2}}}\right)I_{\text{C2}}={\frac {1}{R_{2}}}\left(V_{\text{BE1}}-V_{\text{BE2}}\right)\\&={\frac {V_{\text{T}}}{R_{2}}}\left[\ln \left(I_{\text{C1}}/I_{\text{S1}}\right)-\ln \left(I_{\text{C2}}/I_{\text{S2}}\right)\right]={\frac {V_{\text{T}}}{R_{2}}}\ln \left({\frac {I_{\text{C1}}I_{\text{S2}}}{I_{\text{C2}}I_{\text{S1}}}}\right)\ ,\end{aligned}}}$

where V_T is the thermal voltage.

This equation makes the approximation that the currents are both much larger than the scale currents, I_S1 and I_S2; an approximation valid except for current levels near cut off. In the following, the scale currents are assumed to be identical; in practice, this needs to be specifically arranged.

Design procedure with specified currents

To design the mirror, the output current must be related to the two resistor values R₁ and R₂. A basic observation is that the output transistor is in active mode only so long as its collector-base voltage is non-zero. Thus, the simplest bias condition for design of the mirror sets the applied voltage V_A to equal the base voltage V_B. This minimum useful value of V_A is called the compliance voltage of the current source. With that bias condition, the Early effect plays no role in the design. ^[9]

These considerations suggest the following design procedure:

• Select the desired output current, I_O = I_C2.
• Select the reference current, I_R1, assumed to be larger than the output current, probably considerably larger (that is the purpose of the circuit).
• Determine the input collector current of Q₁, I_C1:

  ${\displaystyle I_{\text{C1}}={\frac {\beta _{1}}{\beta _{1}+1}}\left(I_{\text{R1}}-{\frac {I_{\text{C2}}}{\beta _{2}}}\right)\ .}$

• Determine the base voltage V_BE1 using the Shockley diode law

  ${\displaystyle V_{\text{BE1}}=V_{\text{T}}\ln \left({\frac {I_{\text{C1}}}{I_{\text{S}}}}\right)=V_{\text{A}}\ .}$

where I_S is a device parameter sometimes called the scale current.

The value of base voltage also sets the compliance voltage V_A = V_BE1. This voltage is the lowest voltage for which the mirror works properly.

• Determine R₁:

  ${\displaystyle R_{1}={\frac {V_{\text{CC}}-V_{\text{A}}}{I_{\text{R1}}}}\ .}$

• Determine the emitter leg resistance R₂ using Eq. 1 (to reduce clutter, the scale currents are chosen equal):

  ${\displaystyle R_{2}={\frac {V_{\text{T}}}{\left(1+{\frac {1}{\beta _{2}}}\right)I_{\text{C2}}}}\ln \left({\frac {I_{\text{C1}}}{I_{\text{C2}}}}\right)\ .}$

Finding the current with given resistor values

The inverse of the design problem is finding the current when the resistor values are known. An iterative method is described next. Assume the current source is biased so the collector-base voltage of the output transistor Q₂ is zero. The current through R₁ is the input or reference current given as,

${\displaystyle {\begin{aligned}I_{\text{R1}}&=I_{\text{C1}}+I_{\text{B1}}+I_{\text{B2}}\\&=I_{\text{C1}}+{\frac {I_{\text{C1}}}{\beta _{1}}}+{\frac {I_{\text{C2}}}{\beta _{2}}}\\&={\frac {1}{R_{1}}}\left(V_{\text{CC}}-V_{\text{BE1}}\right)\end{aligned}}}$

Rearranging, I_C1 is found as:

Eq. 2

${\displaystyle I_{\text{C1}}={\frac {\beta _{1}}{\beta _{1}+1}}\left({\frac {V_{\text{CC}}-V_{\text{BE1}}}{R_{1}}}-{\frac {I_{\text{C2}}}{\beta _{2}}}\right)}$

The diode equation provides:

Eq. 3

${\displaystyle V_{\text{BE1}}=V_{\text{T}}\ln \left({\frac {I_{\text{C1}}}{I_{\text{S1}}}}\right)\ .}$

Eq.1 provides:

${\displaystyle I_{\text{C2}}={\frac {V_{\text{T}}}{\left(1+{\frac {1}{\beta _{2}}}\right)R_{2}}}\ln \left({\frac {I_{\text{C1}}}{I_{\text{C2}}}}\right)\ .}$

These three relations are a nonlinear, implicit determination for the currents that can be solved by iteration.

• We guess starting values for I_C1 and I_C2.
• We find a value for V_BE1:

  ${\displaystyle V_{\text{BE1}}=V_{\text{T}}\ln \left({\frac {I_{\text{C1}}}{I_{\text{S1}}}}\right)\ .}$

• We find a new value for I_C1:

  ${\displaystyle I_{\text{C1}}={\frac {\beta _{1}}{\beta _{1}+1}}\left({\frac {V_{\text{CC}}-V_{\text{BE1}}}{R_{1}}}-{\frac {I_{\text{C2}}}{\beta _{2}}}\right)}$

• We find a new value for I_C2:

  ${\displaystyle I_{\text{C2}}={\frac {V_{\text{T}}}{\left(1+{\frac {1}{\beta _{2}}}\right)R_{2}}}\ln \left({\frac {I_{\text{C1}}}{I_{\text{C2}}}}\right)\ .}$

This procedure is repeated to convergence, and is set up conveniently in a spreadsheet. One simply uses a macro to copy the new values into the spreadsheet cells holding the initial values to obtain the solution in short order.

Note that with the circuit as shown, if V_CC changes, the output current will change. Hence, to keep the output current constant despite fluctuations in V_CC, the circuit should be driven by a constant current source rather than using the resistor R₁.

Exact solution

The transcendental equations above can be solved exactly in terms of the Lambert W function.

Output impedance

Figure 2: Small-signal circuit for finding output resistance of the Widlar source shown in Figure 1. A test current I_x is applied at the output, and the output resistance is then R_O = V_x / I_x.

An important property of a current source is its small signal incremental output impedance, which should ideally be infinite. The Widlar circuit introduces local current feedback for transistor ${\displaystyle \scriptstyle Q_{2}}$. Any increase in the current in Q₂ increases the voltage drop across R₂, reducing the V_BE for Q₂, thereby countering the increase in current. This feedback means the output impedance of the circuit is increased, because the feedback involving R₂ forces use of a larger voltage to drive a given current.

Output resistance is found using a small-signal model for the circuit, shown in Figure 2. Transistor Q₁ is replaced by its small-signal emitter resistance r_E because it is diode connected. ^[10] Transistor Q₂ is replaced with its hybrid-pi model. A test current I_x is attached at the output.

Using the figure, the output resistance is determined using Kirchhoff's laws. Using Kirchhoff's voltage law from the ground on the left to the ground connection of R₂:

${\displaystyle I_{\text{b}}\left[(R_{1}\parallel r_{\text{E}})+r_{\pi }\right]+[I_{\text{x}}+I_{\text{b}}]R_{2}=0\ .}$

Rearranging:

${\displaystyle I_{\text{b}}=-I_{\text{x}}{\frac {R_{2}}{(R_{1}\parallel r_{\text{E}})+r_{\pi }+R_{2}}}\ .}$

Using Kirchhoff's voltage law from the ground connection of R₂ to the ground of the test current:

${\displaystyle V_{\text{x}}=I_{\text{x}}(R_{2}+r_{\text{O}})+I_{\text{b}}(R_{2}-\beta r_{\text{O}})\ ,}$

or, substituting for I_b:

Eq. 4

${\displaystyle R_{\text{O}}={\frac {V_{\text{x}}}{I_{\text{x}}}}=r_{\text{O}}\left[1+{\frac {\beta R_{2}}{(R_{1}\parallel r_{\text{E}})+r_{\pi }+R_{2}}}\right]}$${\displaystyle +\ R_{2}\left[{\frac {(R_{1}\parallel r_{\text{E}})+r_{\pi }}{(R_{1}\parallel r_{\text{E}})+r_{\pi }+R_{2}}}\right]\ .}$

According to Eq. 4 , the output resistance of the Widlar current source is increased over that of the output transistor itself (which is r_O) so long as R₂ is large enough compared to the r_π of the output transistor (large resistances R₂ make the factor multiplying r_O approach the value (β + 1)). The output transistor carries a low current, making r_π large, and increase in R₂ tends to reduce this current further, causing a correlated increase in r_π. Therefore, a goal of R₂ ≫ r_π can be unrealistic, and further discussion is provided below. The resistance R₁∥r_E usually is small because the emitter resistance r_E usually is only a few ohms.

Current dependence of output resistance

Figure 3: Design trade-off between output resistance and output current.

Top panel: Circuit output resistance R_Ovs. DC output current I_C2 using the design formula of Eq. 5 for R₂ ;

Center panel: Resistance R_O2 in output transistor emitter leg;

Bottom panel: Feedback factor contributing to output resistance. Current in the reference transistor Q₁ is held constant, thereby fixing the compliance voltage. Plots assume I_C1 = 10 mA, V_A = 50 V, V_CC = 5 V, I_S = 10 fA, β_1, = 100 independently of current.

The current dependence of the resistances r_π and r_O is discussed in the article hybrid-pi model. The current dependence of the resistor values is:

${\displaystyle r_{\pi }={\frac {v_{\text{be}}}{i_{\text{b}}}}{\Bigg |}_{v_{\text{ce}}=0}={\frac {V_{\text{T}}}{I_{\text{B2}}}}=\beta _{2}{\frac {V_{\text{T}}}{I_{\text{C2}}}}\ ,}$

and

${\displaystyle r_{\text{O}}={\frac {v_{\text{ce}}}{i_{\text{c}}}}{\Bigg |}_{v_{\text{be}}=0}={\frac {V_{\text{A}}}{I_{\text{C2}}}}}$

is the output resistance due to the Early effect when V_CB = 0 V (device parameter V_A is the Early voltage).

From earlier in this article (setting the scale currents equal for convenience): Eq. 5

${\displaystyle R_{2}={\frac {V_{\text{T}}}{\left(1+{\frac {1}{\beta _{2}}}\right)I_{\text{C2}}}}\ln \left({\frac {I_{\text{C1}}}{I_{\text{C2}}}}\right)\ .}$

Consequently, for the usual case of small r_E, and neglecting the second term in R_O with the expectation that the leading term involving r_O is much larger: Eq. 6

${\displaystyle {\begin{aligned}R_{\text{O}}&\approx r_{\text{O}}\left(1+{\frac {\beta _{2}R_{2}}{r_{\pi }+R_{2}}}\right)\\&=r_{\text{O}}\left(1+{\frac {\beta _{2}\ln \left({\frac {I_{\text{C1}}}{I_{\text{C2}}}}\right)}{\beta _{2}+1+\ln \left({\frac {I_{\text{C1}}}{I_{\text{C2}}}}\right)}}\right)\end{aligned}}}$

where the last form is found by substituting Eq. 5 for R₂. Eq. 6 shows that a value of output resistance much larger than r_O of the output transistor results only for designs with I_C1 >> I_C2. Figure 3 shows that the circuit output resistance R_O is not determined so much by feedback as by the current dependence of the resistance r_O of the output transistor (the output resistance in Figure 3 varies four orders of magnitude, while the feedback factor varies only by one order of magnitude).

Increase of I_C1 to increase the feedback factor also results in increased compliance voltage, not a good thing as that means the current source operates over a more restricted voltage range. So, for example, with a goal for compliance voltage set, placing an upper limit upon I_C1, and with a goal for output resistance to be met, the maximum value of output current I_C2 is limited.

The center panel in Figure 3 shows the design trade-off between emitter leg resistance and the output current: a lower output current requires a larger leg resistor, and hence a larger area for the design. An upper bound on area therefore sets a lower bound on the output current and an upper bound on the circuit output resistance.

Eq. 6 for R_O depends upon selecting a value of R₂ according to Eq. 5 . That means Eq. 6 is not a circuit behavior formula, but a design value equation. Once R₂ is selected for a particular design objective using Eq. 5 , thereafter its value is fixed. If circuit operation causes currents, voltages or temperatures to deviate from the designed-for values; then to predict changes in R_O caused by such deviations, Eq. 4 should be used, not Eq. 6 .

See also

• Current source
• Current mirror
• Wilson current source

References

1. PR Gray, PJ Hurst, SH Lewis & RG Meyer (2001). Analysis and design of analog integrated circuits (4th ed.). John Wiley and Sons. pp. §4.4.1.1 pp. 299–303. ISBN   0-471-32168-0.
2. AS Sedra & KC Smith (2004). Microelectronic circuits (5th ed.). Oxford University Press. Example 6.14, pp. 654–655. ISBN   0-19-514251-9.
3. MH Rashid (1999). Microelectronic circuits: analysis and design. PWS Publishing Co. pp. 661–665. ISBN   0-534-95174-0.
4. AS Sedra & KC Smith (2004). §9.4.2, p. 899 (5th ed.). ISBN   0-19-514251-9.
5. See, for example, Figure 2 in IC voltage regulators.
6. RJ Widlar: US Patent Number 03320439; Filed May 26, 1965; Granted May 16, 1967: Low-value current source for integrated circuits
7. See Widlar: Some circuit design techniques for linear integrated circuits and Design techniques for monolithic operational amplifiers
8. PR Gray, PJ Hurst, SH Lewis & RG Meyer (2001). Figure 2.38, p. 115. ISBN   0-471-32168-0.
9. Of course, one might imagine a design where the output resistance of the mirror is a major consideration. Then a different approach is necessary.
10. In a diode-connected transistor the collector is short-circuited to the base, so the transistor collector-base junction has no time-varying voltage across it. As a result, the transistor behaves like the base-emitter diode, which at low frequencies has a small-signal circuit that is simply the resistor r_E = V_T / I_E, with I_E the DC Q-point emitter current. See diode small-signal circuit.

Further reading

• Linden T. Harrison (2005). Current Sources and Voltage References: A Design Reference for Electronics Engineers. Elsevier-Newnes. ISBN   0-7506-7752-X.
• Sundaram Natarajan (2005). Microelectronics: Analysis and Design. Tata McGraw-Hill. p. 319. ISBN   0-07-059096-6.
• Current mirrors and active loads: Mu-Huo Cheng