Wire shelving

Last updated May 30, 2024

Wire Shelving is commonly used in industrial and commercial platforms, and more recently in residential use. It is also known as wire decking or ventilated shelving.^[1]

Features

Wire decking consists of wire mesh supported by metal supports and is intended to be load-bearing. The mesh is usually welded to the supports, but may be attached in other ways as well. In commercial and industrial applications, the wire mesh usually has a minimum wire gauge of 0.105 inches when round wire is used. The most common shelf size is 42 inches deep by 46 inches wide, while two such shelves placed side-by-side can usually be combined to allow for a single shelf of 8 feet wide. The weight capacity of a 42x46 shelf ranges from 2,000 to 3,500 pounds, while the decking itself weighs from 24 to 30 pounds. The finish on the steel may either be painted or sprayed on, or be electroplated with zinc. Electroplating is more common with Chinese manufacturers while painting or spraying is more common with American manufacturers.^[2]

Wire shelving is used in a broad range of commercial and home applications. It is often used in restaurant, food service and retail store applications due to its ability to stay clean and resist rust and mold. It is also used by retailers, in industrial applications and in home kitchens as well. Wire shelving is excellent in areas where fire prevention is stressed because its open design allows sprinkler systems to function where solid shelving might block water flow.^{[ citation needed ]}

Chrome-plated steel is much cheaper and much less rust resistant to scratches. Typical colors are chrome, white and black.^{[ citation needed ]}

Manufacturing

Wire shelving for industrial use consists of steel wire, used for the decking, and steel sheets, used for the supports. The wire makes up about 60% of the weight and the sheet steel about 40%.

Coiled steel wire is cut to the correct lengths required using straight-cut machines. Then, these individual wires are fed through a welding machine that joins them, using electric-resistance welding at each junction. The creates a continuous wire mesh, which is then cut to the lengths required.

Manufacturers receive sheets of steel pre-cut for the widths required. The sheets are fed through a roll-forming or stamping machine to create a "U" or "V" shape. The roll-forming machine also cuts the supports to the length required. The "U" shape is significantly stronger and superior to the "V" shape.

After welding, the decking is coated with either baked-on enamel or baked-on powder coating. This requires a cleaning process, heat drying, cooling, paint dip, and then final curing. The decking can instead be electroplated with zinc.

Most manufacturers use the same equipment to produce other products. These include concrete reinforcement, mining, containers and other items made from steel mesh^[2]

Market

In 2008, eleven firms in the United States produced comprised 99% of that country's industry. Most US manufacturers sell wire decking nationwide. Manufacturers usually sell to distributors rather than directly to customers, with big-box retail being a large buyer. Walmart was the number one purchaser for several years during the 2000s. Both US and Chinese firms had high levels of excess capacity around 2010, allowing them to quickly respond to potential increases in demand. Manufacturers reported that the product had changed very little in the previous decade.^[2]

There is no predictable business cycle in the wire decking industry. Demand closely tracks industrial output and real estate construction, but with a 6 to 9-month delay. As a result, the wire decking industry didn't feel the effects of the Great Recession until well into 2009.^[2]

The industry has developed a quality certification called "R-Mark."^[3]

Many manufacturers, especially those importing from Asia do not adhere to the R-Mark standards. This allows them to sell lighter products with arbitrary capacity ratings which can pose a great safety risk.

In the 2000s, US producers accused China of subsidizing wire decking and unfair trade practices. A US Trade Commission investigation rejected these allegations.^[2]

Incompatible standards and labeling

However, not all pole diameters and shelf widths in use are the same. The various plastic connectors are not interchangeable among manufacturers. Many use proprietary designs that do not fit with the systems of other makers. This variance tends to make it difficult to mix and match various brands of shelving.^{[ citation needed ]}

Related Research Articles

A roof is the top covering of a building, including all materials and constructions necessary to support it on the walls of the building or on uprights, providing protection against rain, snow, sunlight, extremes of temperature, and wind. A roof is part of the building envelope.

Spot welding is a type of electric resistance welding used to weld various sheet metal products, through a process in which contacting metal surface points are joined by the heat obtained from resistance to electric current.

Rebar, known when massed as reinforcing steel or steel reinforcement, is a steel bar used as a tension device in reinforced concrete and reinforced masonry structures to strengthen and aid the concrete under tension. Concrete is strong under compression, but has low tensile strength. Rebar significantly increases the tensile strength of the structure. Rebar's surface features a continuous series of ribs, lugs or indentations to promote a better bond with the concrete and reduce the risk of slippage.

Metalworking is the process of shaping and reshaping metals in order to create useful objects, parts, assemblies, and large scale structures. As a term, it covers a wide and diverse range of processes, skills, and tools for producing objects on every scale: from huge ships, buildings, and bridges, down to precise engine parts and delicate jewelry.

Chrome plating is a technique of electroplating a thin layer of chromium onto a metal object. A chrome plated part is called chrome, or is said to have been chromed. The chromium layer can be decorative, provide corrosion resistance, facilitate cleaning, and increase surface hardness. Sometimes, a less expensive substitute for chrome such as nickel may be used for aesthetic purposes.

<span class="mw-page-title-main">Fastener</span> Hardware device that mechanically joins or affixes two or more objects together

A fastener or fastening is a hardware device that mechanically joins or affixes two or more objects together. In general, fasteners are used to create non-permanent joints; that is, joints that can be removed or dismantled without damaging the joining components. Steel fasteners are usually made of stainless steel, carbon steel, or alloy steel.

Plating is a finishing process in which a metal is deposited on a surface. Plating has been done for hundreds of years; it is also critical for modern technology. Plating is used to decorate objects, for corrosion inhibition, to improve solderability, to harden, to improve wearability, to reduce friction, to improve paint adhesion, to alter conductivity, to improve IR reflectivity, for radiation shielding, and for other purposes. Jewelry typically uses plating to give a silver or gold finish.

A staple remover is a device that allows for the quick removal of a staple from a material without causing damage. The best-known form of staple remover, designed for light-gauge staples, consists of two opposing, pivot-mounted pairs of thin, steep wedges and a spring that returns the device to the open position after use. Although a simple metal wedge can be used for the same purpose, and although some staplers feature such a wedge at their hinge end, use of the wedge tends to tear fragile papers.

Sheet metal is metal formed into thin, flat pieces, usually by an industrial process.

A pipe is a tubular section or hollow cylinder, usually but not necessarily of circular cross-section, used mainly to convey substances which can flow — liquids and gases (fluids), slurries, powders and masses of small solids. It can also be used for structural applications; hollow pipe is far stiffer per unit weight than solid members.

Shale shakers are components of drilling equipment used in many industries, such as coal cleaning, mining, oil and gas drilling.They are the first phase of a solids control system on a drilling rig, and are used to remove large solids (cuttings) from the drilling fluid ("mud").

<span class="mw-page-title-main">Cable tray</span> Electrical-cable-supporting structure

In the electrical wiring of buildings, a cable tray system is used to support insulated electrical cables used for power distribution, control, and communication. Cable trays are used as an alternative to open wiring or electrical conduit systems, and are commonly used for cable management in commercial and industrial construction. They are especially useful in situations where changes to a wiring system are anticipated, since new cables can be installed by laying them in the tray, instead of pulling them through a pipe.

Mechanical screening, often just called screening, is the practice of taking granulated or crushed ore material and separating it into multiple grades by particle size.

Galvannealed or galvanneal is the result from the processes of galvanizing followed by annealing of sheet steel.

Pallet rack is a material handling storage aid system designed to store materials on pallets. Although there are many varieties of pallet racking, all types allow for the storage of palletized materials in horizontal rows with multiple levels. Forklift trucks are usually required to place the loaded pallets onto the racks for storage. Since the Second World War, pallet racks have become a ubiquitous element of most modern warehouses, manufacturing facilities, retail centers, and other storage and distribution facilities. All types of pallet racking increase storage density of the stored goods. Costs associated with the racking increases with increasing storage density.

<span class="mw-page-title-main">Oxy-fuel welding and cutting</span> Metalworking technique using a fuel and oxygen

Oxy-fuel welding and oxy-fuel cutting are processes that use fuel gases and oxygen to weld or cut metals. French engineers Edmond Fouché and Charles Picard became the first to develop oxygen-acetylene welding in 1903. Pure oxygen, instead of air, is used to increase the flame temperature to allow localized melting of the workpiece material in a room environment.

A locker is a small, usually narrow storage compartment. They are commonly found in dedicated cabinets, very often in large numbers, in various public places such as locker rooms, workplaces, schools, transport hubs and the like. They vary in size, purpose, construction, and security.

<span class="mw-page-title-main">Strut channel</span> Folded metal struts used in construction

Strut channel, often referred to colloquially by one of several manufacturer trade names, is a standardized formed structural system used in the construction and electrical industries for light structural support, often for supporting wiring, plumbing, or mechanical components such as air conditioning or ventilation systems.

Welded wire mesh, or welded wire fabric, or "weldmesh" is an electric fusion welded prefabricated joined grid consisting of a series of parallel longitudinal wires with accurate spacing welded to cross wires at the required spacing.

Metal furniture is furniture made with metal parts: iron, carbon steel, aluminium, brass and stainless steel.

References

↑ "The Atlantic Monthly". 262. 1988: 82. Retrieved 26 January 2015.{{cite journal}}: Cite journal requires |journal= (help)
1 2 3 4 5 Wire Decking from China, Inv. 701-TA-466 and 731-TA-1162, United States International Trade Commission, July 2010
↑ "R-Mark Certification". Rack Manufacturer's Institute. Retrieved 26 January 2015.

This page is based on this Wikipedia article
Text is available under the CC BY-SA 4.0 license; additional terms may apply.
Images, videos and audio are available under their respective licenses.

[1] "The Atlantic Monthly". 262. 1988: 82. Retrieved 26 January 2015.{{cite journal}}: Cite journal requires |journal= (help)

[:0-2] 1 2 3 4 5 Wire Decking from China, Inv. 701-TA-466 and 731-TA-1162, United States International Trade Commission, July 2010

[3] "R-Mark Certification". Rack Manufacturer's Institute. Retrieved 26 January 2015.

[1]

[2]

[3]