8VSB

Last updated

8VSB is the modulation method used for broadcast in the ATSC digital television standard. ATSC and 8VSB modulation is used primarily in North America; in contrast, the DVB-T standard uses COFDM.

Contents

A modulation method specifies how the radio signal fluctuates to convey information. ATSC and DVB-T specify the modulation used for over-the-air digital television; by comparison, QAM is the modulation method used for cable. The specifications for a cable-ready television, then, might state that it supports 8VSB (for broadcast TV) and QAM (for cable TV).

8VSB is an 8-level vestigial sideband modulation. In essence, it converts a binary stream into an octal representation by amplitude-shift keying a sinusoidal carrier to one of eight levels. 8VSB is capable of transmitting three bits (23=8) per symbol; in ATSC, each symbol includes two bits from the MPEG transport stream which are trellis modulated to produce a three-bit figure. The resulting signal is then band-pass filtered with a Nyquist filter to remove redundancies in the side lobes, and then shifted up to the broadcast frequency. [1]

Modulation technique

Vestigial sideband modulation (VSB) is a modulation method which attempts to eliminate the spectral redundancy of pulse-amplitude modulation (PAM) signals. Modulating a carrier by a real-valued data sequence results in a sum and a difference frequency, resulting in two symmetrical carrier side-bands. The symmetry means that one of the sidebands is redundant, so removing one sideband still allows for demodulation. As filters with zero transition bandwidth cannot be realized, the filtering implemented leaves a vestige of the redundant sideband, hence the name "VSB".

Throughput

In the 6 MHz (megahertz) channel used for broadcast ATSC, 8VSB carries a symbol rate of 10.76 megabaud, a gross bit rate of 32 Mbit/s, and a net bit rate of 19.39 Mbit/s of usable data. The net bit rate is lower due to the addition of forward error correction codes. The eight signal levels are selected with the use of a trellis encoder. There are also similar modulations 2VSB, 4VSB, and 16VSB. 16VSB was notably intended to be used for ATSC digital cable, but quadrature amplitude modulation (QAM) has become the de facto industry standard instead as it is cheap and readily available.

Power saving advantages

[ dubious ]

A significant advantage of 8VSB for broadcasters is that it requires much less power to cover an area comparable to that of the earlier NTSC system, and it is reportedly better at this than the most common alternative system, COFDM.[ citation needed ] Part of the advantage is the lower peak to average power ratio needed compared to COFDM.[ citation needed ] An 8VSB transmitter needs to have a peak power capability of 6 dB (four times) its average power.[ citation needed ] 8VSB is also more resistant to impulse noise.[ citation needed ] Some stations can cover the same area while transmitting at an effective radiated power of approximately 25% of analog broadcast power.[ citation needed ] While NTSC and most other analog television systems also use a vestigial sideband technique, the unwanted sideband is filtered much more effectively in ATSC 8VSB transmissions. 8VSB uses a Nyquist filter to achieve this. Reed–Solomon error correction is the primary system used to retain data integrity.

In summer of 2005, the ATSC published standards for Enhanced VSB, or E-VSB . Using forward error correction, the E-VSB standard will allow DTV reception on low power handheld receivers with smaller antennas in much the same way DVB-H does in Europe, but still using 8VSB transmission.

Disputes over ATSC's use

For some period of time, there had been a continuing lobby for changing the modulation for ATSC to COFDM, the way DVB-T is transmitted in Europe, and ISDB-T in Japan. However, the FCC has always held that 8VSB is the better modulation for use in U.S. digital television broadcasting. In a 1999 report, the Commission found that 8VSB has better threshold or carrier-to-noise (C/N) performance, has a higher data rate capability, requires less transmitter power for equivalent coverage, and is more robust to impulse and phase noise. [2] As a result, it denied in 2000 a petition for rulemaking from Sinclair Broadcast Group requesting that broadcasters be allowed to choose between 8VSB or COFDM as is most appropriate for their area of coverage. [3] The FCC report also acknowledged that COFDM would "generally be expected to perform better in situations where there is dynamic multipath," such as mobile operation or in the presence of trees that are moving in high winds. However, with the introduction of 5th Generation demodulators in 2005 and subsequent improvements in generations 6 and 7, the equalization span is now about −60 to +75 microseconds (a 135 microsecond spread) and has virtually eliminated multipath, both static and dynamic, in 8VSB reception. In comparison, the equalization span in COFDM is −100 to +100 microseconds (200 microsecond spread), but the application of this much guard band space for COFDM substantially reduces its useful payload. In fact, much of Europe has adopted 1280×720p as its HD standard for DVB-T1 because of its reduced payload capacity[ citation needed ]. The introduction of DVB-T2 is meant to increase the ability of terrestrial transmissions to carry 1920×1080p content. 1920×1080i has always been part of the 8VSB scheme from its inception, and its improved demodulators have had no effect on its innate payload capacity[ citation needed ].

Because of continued adoption of the 8VSB-based ATSC standard in the U.S., and a large growing ATSC receiver population, a switch to COFDM will be challenging. Most analog terrestrial transmissions in the US were turned off in June 2009, and 8VSB tuners are common to all new TVs, further complicating a future transition to COFDM.

However, with the development of ATSC 3.0, an updated version of the American digital television standard designed for mobile reception and better single frequency network performance, the ATSC has decided to make the switch to OFDM with LDPC error correction (essentially COFDM). [4] As a result, ATSC 3.0 will be incompatible with all current ATSC 1.0 receivers, and viewers will need a new TV with a compatible tuner or a converter box. [5] Unlike the previous digital TV transition which was mandated by the FCC, the "transition" to ATSC 3.0 will be completely voluntary. Additionally, the FCC has required that broadcasters who decided to make the switch to ATSC 3.0 continue to make their main channel available through a simulcast agreement with another in-market station (with a similar coverage area) through at least 2022. [6] Sinclair announced an intention to bring ATSC 3.0 to 40 cities by 2020. [7]

8VSB vs COFDM

The previously cited FCC Report also found that COFDM has better performance in dynamic and high level static multipath situations, and offers advantages for single frequency networks and mobile reception. Nonetheless, in 2001, a technical report compiled by the COFDM Technical Group concluded that COFDM did not offer any significant advantages over 8VSB. The report recommended in conclusion that receivers be linked to outdoor antennas raised to roughly 30 feet (9 m) in height. Neither 8VSB nor COFDM performed acceptably in most indoor test installations. [8]

However, there were questions[ who? ] whether the COFDM receiver selected for these tests − a transmitter monitor Archived 2007-09-27 at the Wayback Machine lacking normal front end filtering − colored these results. Retests that were performed using the same COFDM receivers with the addition of a front end band pass filter gave much improved results for the DVB-T receiver, but further testing was not pursued.[ permanent dead link ]

The debate over 8VSB versus COFDM modulation is still ongoing. Proponents of COFDM argue that it resists multipath far better than 8VSB. This is important property of the modulation for receiving HDTV in e.g. moving vehicles that is not possible with 8VSB. Early 8VSB DTV (digital television) receivers often had difficulty receiving a signal in urban environments. Newer 8VSB receivers, however, are better at dealing with multipath, but a moving receiver can still not receive the signal. Moreover, 8VSB modulation requires less power to transmit a signal the same distance. In less populated areas, 8VSB may outperform COFDM because of this. However, in some urban areas, as well as for mobile use, COFDM may offer better reception than 8VSB. Several "enhanced" VSB systems were in development, most notably E-VSB, A-VSB, and MPH. The deficiencies in 8VSB in regards to multipath reception can be dealt with by using additional forward error-correcting codes which decreases the useful bit rate, such as that used by ATSC-M/H for Mobile/Handheld reception. ATSC 3.0, the next major television standard in the United States, will use COFDM.

The vast majority of U.S. TV stations use COFDM for their studio to transmitter links and news gathering operations[ citation needed ]. These are point-to-point communication links and not broadcast transmissions.

See also

Related Research Articles

<span class="mw-page-title-main">Digital television</span> Television transmission using digital encoding

Digital television (DTV) is the transmission of television signals using digital encoding, in contrast to the earlier analog television technology which used analog signals. At the time of its development it was considered an innovative advancement and represented the first significant evolution in television technology since color television in the 1950s. Modern digital television is transmitted in high-definition television (HDTV) with greater resolution than analog TV. It typically uses a widescreen aspect ratio in contrast to the narrower format (4:3) of analog TV. It makes more economical use of scarce radio spectrum space; it can transmit up to seven channels in the same bandwidth as a single analog channel, and provides many new features that analog television cannot. A transition from analog to digital broadcasting began around 2000. Different digital television broadcasting standards have been adopted in different parts of the world; below are the more widely used standards:

<span class="mw-page-title-main">Orthogonal frequency-division multiplexing</span> Method of encoding digital data on multiple carrier frequencies

In telecommunications, orthogonal frequency-division multiplexing (OFDM) is a type of digital transmission used in digital modulation for encoding digital (binary) data on multiple carrier frequencies. OFDM has developed into a popular scheme for wideband digital communication, used in applications such as digital television and audio broadcasting, DSL internet access, wireless networks, power line networks, and 4G/5G mobile communications.

DVB-T, short for Digital Video Broadcasting – Terrestrial, is the DVB European-based consortium standard for the broadcast transmission of digital terrestrial television that was first published in 1997 and first broadcast in Singapore in February, 1998. This system transmits compressed digital audio, digital video and other data in an MPEG transport stream, using coded orthogonal frequency-division multiplexing modulation. It is also the format widely used worldwide for Electronic News Gathering for transmission of video and audio from a mobile newsgathering vehicle to a central receive point. It is also used in the US by Amateur television operators.

<span class="mw-page-title-main">ATSC standards</span> Standards for digital television in the US

Advanced Television Systems Committee (ATSC) standards are an International set of standards for broadcast and digital television transmission over terrestrial, cable and satellite networks. It is largely a replacement for the analog NTSC standard and, like that standard, is used mostly in the United States, Mexico, Canada, South Korea and Trinidad & Tobago. Several former NTSC users, such as Japan, have not used ATSC during their digital television transition, because they adopted other systems such as ISDB developed by Japan, and DVB developed in Europe, for example.

<span class="mw-page-title-main">Digital Radio Mondiale</span> Digital radio broadcasting standard

Digital Radio Mondiale is a set of digital audio broadcasting technologies designed to work over the bands currently used for analogue radio broadcasting including AM broadcasting—particularly shortwave—and FM broadcasting. DRM is more spectrally efficient than AM and FM, allowing more stations, at higher quality, into a given amount of bandwidth, using xHE-AAC audio coding format. Various other MPEG-4 codecs and Opus are also compatible, but the standard now specifies xHE-AAC.

Digital radio is the use of digital technology to transmit or receive across the radio spectrum. Digital transmission by radio waves includes digital broadcasting, and especially digital audio radio services.

16VSB is an abbreviation for 16-level vestigial sideband modulation, capable of transmitting four bits (24=16) at a time.

Broadcasttelevision systems are the encoding or formatting systems for the transmission and reception of terrestrial television signals.

<span class="mw-page-title-main">Amateur television</span> Transmission of video in amateur radio bands

Amateur television (ATV) is the transmission of broadcast quality video and audio over the wide range of frequencies of radio waves allocated for radio amateur (Ham) use. ATV is used for non-commercial experimentation, pleasure, and public service events. Ham TV stations were on the air in many cities before commercial television stations came on the air. Various transmission standards are used, these include the broadcast transmission standards of NTSC in North America and Japan, and PAL or SECAM elsewhere, utilizing the full refresh rates of those standards. ATV includes the study of building of such transmitters and receivers, and the study of radio propagation of signals travelling between transmitting and receiving stations.

The Grand Alliance (GA) was a consortium created in 1993 at the behest of the Federal Communications Commission (FCC) to develop the American digital television and HDTV specification, with the aim of pooling the best work from different companies. It consisted of AT&T Corporation, General Instrument Corporation, Massachusetts Institute of Technology, Philips Consumer Electronics, David Sarnoff Research Center, Thomson Consumer Electronics, and Zenith Electronics Corporation. The Grand Alliance's DTV system is the basis for the ATSC standard.

<span class="mw-page-title-main">Single-frequency network</span>

A single-frequency network or SFN is a broadcast network where several transmitters simultaneously send the same signal over the same frequency channel.

QAM is a digital television standard using quadrature amplitude modulation. It is the format by which digital cable channels are encoded and transmitted via cable television providers. QAM is used in a variety of communications systems such as Dial-up modems and WiFi. In cable systems, a QAM tuner is linked to the cable in a manner that is equivalent to an ATSC tuner which is required to receive over-the-air (OTA) digital channels broadcast by local television stations when attached to an antenna. Most new HDTV digital televisions support both of these standards. QAM uses the same 6 MHz bandwidth as ATSC, using a standard known as ITU-T Recommendation J.83 Annex B ("J.83b").

<span class="mw-page-title-main">ATSC tuner</span> Tuner for digital television channels

An ATSCtuner, often called an ATSC receiver or HDTV tuner, is a type of television tuner that allows reception of digital television (DTV) television channels that use ATSC standards, as transmitted by television stations in North America, parts of Central America, and South Korea. Such tuners are usually integrated into a television set, VCR, digital video recorder (DVR), or set-top box which provides audio/video output connectors of various types.

<span class="mw-page-title-main">Digital television adapter</span> Type of television tuner to display digital signals on analog sets

A digital television adapter (DTA), commonly known as a converter box or decoder box, is a television tuner that receives a digital television (DTV) transmission, and converts the digital signal into an analog signal that can be received and displayed on an analog television set. Some also have an HDMI output since some TVs with HDMI do not have a digital tuner. The input digital signal may be over-the-air terrestrial television signals received by a television antenna, or signals from a digital cable system. It normally does not refer to satellite TV, which has always required a set-top box either to operate the big satellite dish, or to be the integrated receiver/decoder (IRD) in the case of direct-broadcast satellites (DBS).

E-VSB or Enhanced VSB is an optional enhancement to the original ATSC Standards that use the 8VSB modulation system used for transmission of digital television. It is intended for improving reception where signals are weaker, including fringe reception areas, and on portable devices such as handheld televisions or mobile phones. It does not cause problems to older receivers, but they cannot take advantage of its features. E-VSB was approved by the ATSC committee in 2004. However, it has been implemented by few stations or manufacturers.

A-VSB or Advanced VSB is a modification of the 8VSB modulation system used for transmission of digital television using the ATSC system. One of the constraints of conventional ATSC transmission is that reliable reception is difficult or impossible when the receiver is moving at speeds associated with normal vehicular traffic. The technology was jointly developed by Samsung and Rohde & Schwarz.

ATSC-M/H is a U.S. standard for mobile digital TV that allows TV broadcasts to be received by mobile devices.

The digital transition in the United States was the switchover from analog to exclusively digital broadcasting of terrestrial television programming. According to David Rehr, then president and CEO of the National Association of Broadcasters, this transition represented "the most significant advancement of television technology since color TV was introduced." For full-power TV stations, the transition went into effect on June 12, 2009, with stations ending regular programming on their analog signals no later than 11:59 p.m. local time that day.

In North American digital terrestrial television broadcasting, a distributed transmission system is a form of single-frequency network in which a single broadcast signal is fed via microwave, landline, or communications satellite to multiple synchronised terrestrial radio transmitter sites. The signal is then simultaneously broadcast on the same frequency in different overlapping portions of the same coverage area, effectively combining many small transmitters to generate a broadcast area rivalling that of one large transmitter or to fill gaps in coverage due to terrain or localised obstacles.

References

  1. Sparano, David (1997). "WHAT EXACTLY IS 8-VSB ANYWAY?" (PDF). Retrieved 8 Nov 2012.
  2. DTV REPORT ON COFDM AND 8-VSB PERFORMANCE (PDF), FCC Office of Engineering and Technology, archived (PDF) from the original on 14 April 2007, retrieved 2007-03-04, September 30, 1999.
  3. Sinclair Claims Wide Support For Dtv Petition, Television Digest with Consumer Electronics, 1999, archived from the original on 2004-09-02, retrieved 2008-06-06, Oct 11, 1999.
  4. "ATSC 3.0 Technical overview" (PDF). Rohde & Schwarz. 8 March 2021. Archived (PDF) from the original on 8 March 2021. Retrieved 8 March 2021.
  5. Cohen, Simon. "ATSC 3.0: Everything you need to know about broadcast TV's next big thing". Digital Trends. Designtechnica Corporation. Archived from the original on 29 November 2020. Retrieved 8 March 2021.
  6. "Report and Order and Further Notice of Proposed Rulemaking". Federal Communications Commission. 20 November 2017. Archived from the original on 18 October 2020. Retrieved 8 March 2021.
  7. Munson, Ben (8 April 2019). "Sinclair announces 40 U.S. cities getting ATSC 3.0 by 2020". Fierce Video. Archived from the original on 8 March 2021. Retrieved 8 March 2021.
  8. 8VSB/COFDM Comparison Report Archived 2005-11-22 at the Wayback Machine