EN 207

Last updated
EN207-compliant laser goggles. The user has added yellow stickers summarizing the complicated EN207 specifications shown in the inset. Laser goggles en207.jpg
EN207-compliant laser goggles. The user has added yellow stickers summarizing the complicated EN207 specifications shown in the inset.

EN 207 is a European norm for laser safety eyewear (now superseded, together with the EN 208, by the ISO 19818:2021 standard [1] ). Any laser eye protection sold within the European Community must be certified and labeled with the CE mark. According to this standard, laser safety glasses should not only absorb laser light of a given wavelength, but they should also be able to withstand a direct hit from the laser without breaking or melting, both the filter and the frame. In this respect, the European norm is more strict than the American norm (ANSI Z 136) that only regulates the required optical density. More precisely, the safety glasses should be able to withstand a continuous wave laser for 5 seconds, or 50 pulses for a pulsed laser (EN 207:2017). [2]

Contents

An EN 207 specification might read IR 315–532 LB6. Here, the letters IR indicate the laser working mode, in this case a pulsed mode. The range 315–532 indicates the wavelength range in nanometers. Finally, the scale number LB6 indicates a lower limit for the optical density, i.e. the transmittance within this wavelength range is less than 10−6.


Laser working modes

EN 207 specifies four laser working modes:

Working modeLetterPulse length
Continuous wave D> 0.25 s
Pulsed modeI> 1 μs–0.25 s
Giant pulsed modeR> 1 ns–1 μs
ModelockedM< 1 ns

Scale numbers

The scale numbers range from LB1 to LB10, where the number is a lower limit for the optical density, i.e. LBn means that OD > n, or , where T is the transmittance. The minimum scale number for a given laser with a beam diameter of 1 mm depends on the working mode and the wavelength as follows (EN 207:2017):

Working modeWavelength rangeMaximum laser
power density
Minimum protection level
for given power*
D (continuous)180–315 nm1×10n3 W/m2log(P) + 3
>315–1400 nm1×10n+1 W/m2log(P) 1
>1400 nm–1000 μm1×10n+3 W/m2log(P) 3
I,R (pulsed)180–315 nm3×10n+1 J/m2log(E/3) 1
>315–1400 nm5×10n3 J/m2log(E/5) + 3
>1400 nm–1000 μm1×10n+2 J/m2log(E) 2
M (ultrashort pulses)180–315 nm3×10n+10 W/m2log(P/3) 10
>315–1400 nm1.5×10n4 J/m2log(E/1.5) + 4
>1400 nm–1000 μm1×10n+11 W/m2log(P) 11
*P in W/m2, E in J/m2.
Level numbers should be rounded upwards.

If the beam diameter differs from 1 mm a correction factor, depending on the material of the filter and frame, must be applied. Another correction factor must be used for pulsed lasers in case of repeated pulses for wavelengths above 400 nm.

Examples
  1. the laser operates at 1064 nm and has a pulse duration of 10 ns, 100 mJ/cm2 (or 103 J/m2). You have goggles that are specified as DIR 1064 LB5. The pulse duration indicates that we should look at the R specification, with scale number n=5, which gives an upper limit of 5×102 J/m2, which means that these goggles do not offer suitable protection for this particular laser.
  2. the laser operates at 780 nm, is continuous wave with an intensity of 50 mW/cm2 (P = 500 W/m2). This means you need a D protection level of , which is rounded up to 2. In other words, the safety goggles should be at least D 780 LB2.
  3. such example can be found too 900 - 1070 D LB7 + IR LB8 + M LB8Y.
    The symbols have the same meaning as in the previous examples, just note on marking with Y: if the eye protection device has not been tested with low repetition frequencies (≤ 25 Hz), the protection level must be extended by the letter Y . [3]

From the scale it can be inferred that the power densities that correspond to are considered safe without protective eyewear.

Related Research Articles

<span class="mw-page-title-main">Laser</span> Device which emits light via optical amplification

A laser is a device that emits light through a process of optical amplification based on the stimulated emission of electromagnetic radiation. The word laser is an anacronym that originated as an acronym for light amplification by stimulated emission of radiation. The first laser was built in 1960 by Theodore Maiman at Hughes Research Laboratories, based on theoretical work by Charles H. Townes and Arthur Leonard Schawlow.

<span class="mw-page-title-main">Microscopy</span> Viewing of objects which are too small to be seen with the naked eye

Microscopy is the technical field of using microscopes to view objects and areas of objects that cannot be seen with the naked eye. There are three well-known branches of microscopy: optical, electron, and scanning probe microscopy, along with the emerging field of X-ray microscopy.

<span class="mw-page-title-main">Raman spectroscopy</span> Spectroscopic technique

Raman spectroscopy is a spectroscopic technique typically used to determine vibrational modes of molecules, although rotational and other low-frequency modes of systems may also be observed. Raman spectroscopy is commonly used in chemistry to provide a structural fingerprint by which molecules can be identified.

<span class="mw-page-title-main">Sunglasses</span> Eyewear for protecting against bright light

Sunglasses or sun glasses are a form of protective eyewear designed primarily to prevent bright sunlight and high-energy visible light from damaging or discomforting the eyes. They can sometimes also function as a visual aid, as variously termed spectacles or glasses exist, featuring lenses that are colored, polarized or darkened. In the early 20th century, they were also known as sun cheaters.

Mode locking is a technique in optics by which a laser can be made to produce pulses of light of extremely short duration, on the order of picoseconds (10−12 s) or femtoseconds (10−15 s). A laser operated in this way is sometimes referred to as a femtosecond laser, for example, in modern refractive surgery. The basis of the technique is to induce a fixed phase relationship between the longitudinal modes of the laser's resonant cavity. Constructive interference between these modes can cause the laser light to be produced as a train of pulses. The laser is then said to be "phase-locked" or "mode-locked".

<span class="mw-page-title-main">Titanium-sapphire laser</span> Type of laser

Titanium-sapphire lasers (also known as Ti:sapphire lasers, Ti:Al2O3 lasers or Ti:sapphs) are tunable lasers which emit red and near-infrared light in the range from 650 to 1100 nanometers. These lasers are mainly used in scientific research because of their tunability and their ability to generate ultrashort pulses thanks to its broad light emission spectrum. Lasers based on Ti:sapphire were first constructed and invented in June 1982 by Peter Moulton at the MIT Lincoln Laboratory.

<span class="mw-page-title-main">Optical filter</span> Filters which selectively transmit specific colors

An optical filter is a device that selectively transmits light of different wavelengths, usually implemented as a glass plane or plastic device in the optical path, which are either dyed in the bulk or have interference coatings. The optical properties of filters are completely described by their frequency response, which specifies how the magnitude and phase of each frequency component of an incoming signal is modified by the filter.

<span class="mw-page-title-main">Laser safety</span> Protocols for safe use, design and implementation of laser technology

Laser radiation safety is the safe design, use and implementation of lasers to minimize the risk of laser accidents, especially those involving eye injuries. Since even relatively small amounts of laser light can lead to permanent eye injuries, the sale and usage of lasers is typically subject to government regulations.

<span class="mw-page-title-main">Laser pointer</span> Handheld device that emits a laser beam

A laser pointer or laser pen is a handheld device that uses a laser diode to emit a narrow low-power visible laser beam to highlight something of interest with a small bright colored spot.

<span class="mw-page-title-main">Eye protection</span> Protective gear for the eyes

Eye protection is protective gear for the eyes, and sometimes face, designed to reduce the risk of injury. Examples of risks requiring eye protection can include: impact from particles or debris, light or radiation, wind blast, heat, sea spray or impact from some type of ball or puck used in sports.

Chirped pulse amplification (CPA) is a technique for amplifying an ultrashort laser pulse up to the petawatt level, with the laser pulse being stretched out temporally and spectrally, then amplified, and then compressed again. The stretching and compression uses devices that ensure that the different color components of the pulse travel different distances.

<span class="mw-page-title-main">Neutral-density filter</span> Device in optics that reduces light intensity

In photography and optics, a neutral-density filter, or ND filter, is a filter that reduces or modifies the intensity of all wavelengths, or colors, of light equally, giving no changes in hue of color rendition. It can be a colorless (clear) or grey filter, and is denoted by Wratten number 96. The purpose of a standard photographic neutral-density filter is to reduce the amount of light entering the lens. Doing so allows the photographer to select combinations of aperture, exposure time and sensor sensitivity that would otherwise produce overexposed pictures. This is done to achieve effects such as a shallower depth of field or motion blur of a subject in a wider range of situations and atmospheric conditions.

<span class="mw-page-title-main">Shiva laser</span>

The Shiva laser was a powerful 20-beam infrared neodymium glass laser built at Lawrence Livermore National Laboratory in 1977 for the study of inertial confinement fusion (ICF) and long-scale-length laser-plasma interactions. Presumably, the device was named after the multi-armed form of the Hindu god Shiva, due to the laser's multi-beamed structure. Shiva was instrumental in demonstrating a particular problem in compressing targets with lasers, leading to a major new device being constructed to address these problems, the Nova laser.

This is a list of acronyms and other initialisms used in laser physics and laser applications.

<span class="mw-page-title-main">Welding helmet</span> Helmet that protects eyes during welding

A welding helmet is a type of personal protective equipment used in performing certain types of welding to protect the eyes, face, and neck from flash burn, sparks, infrared and ultraviolet light, and intense heat. The modern welding helmet used today was first introduced in 1937 by Willson Products.

<span class="mw-page-title-main">Supercontinuum</span>

In optics, a supercontinuum is formed when a collection of nonlinear processes act together upon a pump beam in order to cause severe spectral broadening of the original pump beam, for example using a microstructured optical fiber. The result is a smooth spectral continuum. There is no consensus on how much broadening constitutes a supercontinuum; however researchers have published work claiming as little as 60 nm of broadening as a supercontinuum. There is also no agreement on the spectral flatness required to define the bandwidth of the source, with authors using anything from 5 dB to 40 dB or more. In addition the term supercontinuum itself did not gain widespread acceptance until this century, with many authors using alternative phrases to describe their continua during the 1970s, 1980s and 1990s.

<span class="mw-page-title-main">Output coupler</span> Part of an optical resonator which allows intracavity light to be emitted

In laser science, an output coupler (OC) is the component of an optical resonator that allows the extraction of a portion of the light from the laser's intracavity beam. An output coupler most often consists of a partially reflective mirror, allowing a certain portion of the intracavity beam to transmit through. Other methods include the use of almost-totally reflective mirrors at each end of the cavity, emitting the beam either by focusing it into a small hole drilled in the center of one mirror, or by redirecting through the use of rotating mirrors, prisms, or other optical devices, causing the beam to bypass one of the end mirrors at a given time.

<span class="mw-page-title-main">Photoionization mode</span>

A photoionization mode is a mode of interaction between a laser beam and matter involving photoionization.

<span class="mw-page-title-main">Laser beam profiler</span> Measurement device

A laser beam profiler captures, displays, and records the spatial intensity profile of a laser beam at a particular plane transverse to the beam propagation path. Since there are many types of lasers—ultraviolet, visible, infrared, continuous wave, pulsed, high-power, low-power—there is an assortment of instrumentation for measuring laser beam profiles. No single laser beam profiler can handle every power level, pulse duration, repetition rate, wavelength, and beam size.

<span class="mw-page-title-main">Fourier domain mode locking</span>

Fourier domain mode locking (FDML) is a laser modelocking technique that creates a continuous wave, wavelength-swept light output.

References

  1. ISO 19818:2021 (This standard supersedes the SS-EN 208:2010, edition 3 and SS-EN 207:2017, edition 4).
  2. SS-EN 207:2017 (E) EUROPEAN STANDARD EN 207 - Personal eye-protection equipment - Filters and eye-protectors against laser radiation (laser eye-protectors) (ICS 13.340.20). CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels: EUROPEAN COMMITTEE FOR STANDARDIZATION. March 2017.{{cite book}}: CS1 maint: location (link)
  3. "DGUV Information 203-042 - Auswahl und Benutzung von Laser-Schutzbrillen, Laser-Justierbrillen und Laser-Schutzabschirmungen | Schriften".