Maple Mill, Oldham

Last updated

Maple Mill
Maple Mill (3468230750).jpg
Maple Mill No. 1 in 2009
Greater Manchester UK location map 2.svg
Red pog.svg
Location in Greater Manchester
Cotton
Location Hathershaw, Oldham, Greater Manchester, England
Further ownership
  • Courtaulds (spinning in the 1990s) ()
Current owners Vance Miller
Coordinates 53°31′35″N2°06′26″W / 53.526325°N 2.1071023°W / 53.526325; -2.1071023 Coordinates: 53°31′35″N2°06′26″W / 53.526325°N 2.1071023°W / 53.526325; -2.1071023
Construction
BuiltMaple No.1: 1904
Maple No.2: 1915
Renovated
  • 1:Maple No.1: 1990
DemolishedMaple No.2: 2009 (Fire)
Maple No.1: 2016 (Fire)
Design team
Architect P.S.Stott
Power
Date1904 [1]
Engine makerMaple No.1: George Saxon & Co
Maple No.2: Urmson & Thompson [2]
Engine typeMaple No.1: vertical triple expansion engine
*18 ½" HGP,
*29" IP,
* 47"LP
Valve GearMaple No.1: Corliss
Cylinder diameter and throwMaple No.1: 48 in
rpmMaple No.1: 75
Installed horse power (ihp)Maple No.1: 1000
Maple No.2: 1800
Flywheel diameterMaple No.1: 22 ft
Transmission typerope
Boiler configuration
PressureMaple No.1: 185
Equipment
ManufacturerPlatts
References
[3]

The Maple Mill was a cotton spinning mill in Hathershaw, Oldham, Greater Manchester, England. It was designed as a double mill by the architect Sydney Stott. The first mill was built in 1904 and the second mill in 1915. In 1968, it was equipped with the first open-end spinning machines in England. When spinning ceased in the 1990s, it was bought by Vance Miller. Trading Standards raided the mill in 2006, and ordered Mr Miller stop selling products that failed national safety provisions. Maple Mill No. 2 was the first mill to be partially destroyed by a fire on April 21, 2009. The fire brigade was in attendance for two weeks and deployed 34 appliances. Later on in 2016, Maple Mill No. 1 was damaged by fire on September 30. On 15 December 2016 a major incident was declared when the same mill became fully ablaze. The land of the two mills has now been cleared fully since 2021, including its chimney, and the site is now going to be housing.

Contents

Architecture

Maple Mill was a double mill. Maple No.2 was designed by P.S.Stott, so the round chimney carried the double rings that were his trademark. This was a six-storey red brick mill built in 1904. Stott did not use concrete floors but a triple brick arched vault construction, however here there was a concrete ceiling. Though the chimney stands it has been truncated.

Power

Maple No. 1 was powered by a 1000 hp vertical triple-expansion engine built by George Saxon & Co, of Openshaw. It had a 48-inch stroke, and its high-pressure cylinder was 18+1⁄2 inches in diameter. The intermediate-pressure was 29 inches, and the low-pressure was 47 inches. It was pressured to 185 psi, and ran a 22 ft flywheel at 75 rpm. There were Corliss valves on all cylinders. The air pump was driven from LP crosshead. [1] Maple No.2 was powered by an 1800 hp engine from Urmson & Thompson. [2]

Equipment

Both mills ran mules supplied by Platts. [2] Maple I had 114,456 Spindles and Maple 2 had 55,888 Spindles. [4]

History

It was designed as a double mill by P.S.Stott, in 1904. The first mill was built then and the second mill in 1915. It worked as a mule spinning mill.

It was taken over by Fine Spinners and Doublers in the 1950s.

Maple Mill was sold to Courtaulds in 1964. In 1968, Maple Mill was selected by Courtaulds to receive the first top secret BD 200s, Open End Spinning machines from Czechoslovakia. These were experimental, and coming without documentation were difficult to operate. Simply, they were designed for Uzbek cotton not the American cotton or synthetics used in Oldham. A research visit by Courtaulds staff to Ústí nad Labem in August 1968, was interrupted by Soviet tanks putting down the Prague spring uprising. Later a body of Czech technicians was based at Maple Mill, until the problems had been resolved. This was a rare example of cross Iron Curtain co-operation. [5] Courtaulds ceased cotton spinning at the mill in 1991, but it was re-opened a year later by Wills Fabrics Ltd who continued spinning and weaving on the site until the company went into administration 1998.

Vance Miller ownership

It was bought by Vance Miller and used to manufacture and market fitted kitchens and furniture.

In 2006 the Greater Manchester Police and Trading Standards raided the Maple Mill offices and factory of Vance Miller. As a result of the raids four people, including Miller, were arrested on suspicion of conspiracy to defraud in what was one of Tradings Standards' biggest ever operations. [6] The company was able to continue trading despite Trading Standards seizing property in a bid to pursue its case against the company.

On 21 February 2007, under the General Product Safety Regulations Act 2005, Trading Standards Officers in Oldham ordered Vance Miller, again trading from Maple Mill, to immediately withdraw four types of minibikes from sale. The products failed national safety provisions. [7]

Fires

Maple Mills after the 2009 fire. Mill 1 is on the left. The remains of Mill 2 are on the right. Maple Mill after fire (3469851532).jpg
Maple Mills after the 2009 fire. Mill 1 is on the left. The remains of Mill 2 are on the right.

On 21 April 2009, a fire started near the diesel generator of the kitchen factory (Maple No.2) and ignited the contents of propane cylinders and pallets. [8] Sixty firefighters used ten fire engines and "a number of specialist appliances, including two aerial appliances, to contain the fire." [8] Fire Service spokesman Paul Duggan said: "The fire is thought to have started in a diesel generator then spread to some wooden pallets and propane cylinders nearby, some of which exploded as a result. There were people inside at the time but there were no reported injuries or any reports of anyone missing." Local townspeople near the area had been left without water or very little [9] The building is burnt out. The fire was the largest incident attended by Greater Manchester Fire Service for several years. At the height of the fire, a total of 34 fire appliances from across Manchester attended including three aerial appliances, Hose Layers and High Volume Pumping Units. The Fire Service were in continuous attendance for two weeks.

On 30 September 2016 a fire devastated the first floor of Maple No.1 mill. [10]

On the morning of 15 December 2016 another fire started at the Maple No.1. [11] The fire started on the top floor of the mill. [12] Around 70 firefighters attended, with nearby properties evacuated. [11] The building was declared to be structurally unstable as a result of the fire, [13] during which large parts of the building collapsed, and work to demolish unsafe portions of the mill began on 16 December, [14] expected to take three days. [12] Although the mill was vacant, some people may have been sleeping inside it. [11] [15] People living in caravans had been seen at the site since September 2016, [15] [14] with Vance Miller saying that the fire would not have started if travellers had been evicted from the site. [12] Fire crews left the mill on 24 December, nine days after the fire started; most of the mill was demolished, with only a tower remaining. [16]

See also

Related Research Articles

Vance Miller is an entrepreneur from Rochdale, Lancashire, in England. Miller, whose business practices have attracted controversy, has been referred to in the media as "The Kitchen Gangster" after being featured the 2004 BBC series "Saturday Kitchen Gangster".

The Stotts were a family of architects from Oldham, North West England, of Scottish descent who specialised in the design of cotton mills. James Stott was the father, Joseph and his elder brother Abraham Stott had rival practices, and in later years did not communicate. Their children continue their practices.

Sir Philip Sidney Stott, 1st Baronet, usually known by his full name or as Sidney Stott, was an English architect, civil engineer and surveyor.

<span class="mw-page-title-main">Atlas Mill, Ashton-under-Lyne</span> Cotton mill in Greater Manchester, England

Atlas Mill was a cotton spinning mill in the Waterloo district of Ashton-under-Lyne, Greater Manchester, in England. It was built between 1898 and 1900 for the Ashton Syndicate by Sydney Stott of Oldham. It was last mill in Ashton to cease spinning. It was spinning artificial fibres in 1987, and was demolished in 1994; the site is now a housing estate.

<span class="mw-page-title-main">Texas Mill, Ashton-under-Lyne</span> Former cotton spinning mill in Ashton-under-Lyne, England

Texas Mill was a cotton spinning mill in the Whitelands district of Ashton-under-Lyne, Greater Manchester, in England. It was built between 1905 and 1907 for the Ashton Syndicate by Sydney Stott of Oldham. It was destroyed in a massive fire on 22–23 October 1971. It had been re-equipped as a ring mill for spinning artificial fibres when it was destroyed.

<span class="mw-page-title-main">Cedar Mill, Ashton-under-Lyne</span>

Cedar Mill was a cotton spinning mill in the Hurst area of Ashton-under-Lyne, Greater Manchester, in England. It was built between 1903 and 1905 for the Ashton Syndicate by Sydney Stott of Oldham. It was the last mill in Ashton spinning cotton. It ceased in 1980. It was demolished and the land was used for housing.

<span class="mw-page-title-main">Rutland Mill</span> Cotton mill in Greater Manchester, England

Rutland Mill was a cotton spinning mill on Linney Lane, in Shaw and Crompton, Greater Manchester, England. It was built by F. W. Dixon & Son in 1907 for the Rutland Mill Co. Ltd. It was taken over by the Lancashire Cotton Corporation in 1935. By 1964, it was in the Courtaulds Group. In the late 1980s, as Courtaulds moved operations to other parts of the world, the mill was bought by Littlewoods who demolished it and replaced it with a new automated storage warehouse.

Magnet Mill, Chadderton is a cotton spinning mill in Chadderton, Oldham, Greater Manchester. It was built by the Magnet Mill Ltd. in 1902, but purchased by the Lancashire Cotton Corporation in 1935. It was later taken over by the Courtaulds Group. Ceasing textile production in December 1966, it was demolished soon after. A suburban residential estate now occupies this site. It was driven by a 2200 hp twin tandem compound engine by George Saxon & Co, Openshaw, 1903. It had a 27-foot flywheel with 35 ropes, operating at 64½ rpm.

<span class="mw-page-title-main">Hawk Mill, Shaw</span> Cotton mill in Greater Manchester, England

Hawk Mill, Shaw was a cotton spinning mill in Shaw, Oldham, Greater Manchester. It was built in 1908. It was taken over by the Lancashire Cotton Corporation in the 1931 and passed to Courtaulds in 1964. The mill closed in 1967, and was demolished in 1991.

<span class="mw-page-title-main">Ace Mill, Hollinwood</span>

Ace Mill is a cotton spinning mill in Chadderton in the Metropolitan Borough of Oldham, Greater Manchester. It was built as Gorse No. 2 Mill, in 1914 and cotton was first spun in 1919 by the Ace Mill Ltd, who renamed the mill. It was taken over by the Lancashire Cotton Corporation in the 1930s and passed to Courtaulds in 1964. Production ended in 1967.

<span class="mw-page-title-main">Dawn Mill, Shaw</span> Cotton mill in Greater Manchester, England

Dawn Mill, Shaw was a cotton spinning mill in Shaw and Crompton, Oldham, Greater Manchester. It was built on the site of Shaw Mill at the "dawn" of the 20th century. Dawn Mill was equipped with mule weft spindles in 1950. It was powered by Engines named Venus and Mars, 1800 hp twin tandem compound engine by George Saxon of Manchester. It was taken over by the Lancashire Cotton Corporation in the 1930s and passed to Courtaulds in 1964. It was sold again and used by distribution company DTS Logistics for storing and distributing clothing. It was demolished in 2006 to make way for an Asda supermarket.

<span class="mw-page-title-main">Royton Ring Mill, Royton</span> Cotton mill in Greater Manchester, England

Royton Ring Mill was a cotton mill in Royton, Greater Manchester, England. It was built in 1908 and extended in 1912. It was taken over by the Lancashire Cotton Corporation in 1935 and passed to Courtaulds in 1964. Production finished in 1966. It was extended again in 1969 and used for other purposes. It has now been demolished, the street has been renamed and houses replace it.

<span class="mw-page-title-main">Kent Mill, Chadderton</span>

Kent Mill, Chadderton was a cotton spinning mill in Chadderton, Oldham, Greater Manchester. It was built in 1908 for the Kent Mill Co. It was taken over by the Lancashire Cotton Corporation in 1938 and passed to Courtaulds in 1964. Production finished in 1991 and it was demolished in 1994.

<span class="mw-page-title-main">Manor Mill, Chadderton</span> Cotton mill in Greater Manchester, England

Manor Mill, Chadderton is an early twentieth century, five storey cotton spinning mill in Chadderton, Oldham, Greater Manchester. It was built in 1906. It was taken over by the Lancashire Cotton Corporation in the 1930s and passed to Courtaulds in 1964. Production finished in 1990.

<span class="mw-page-title-main">Heron Mill, Hollinwood</span> Cotton spinning mill in Oldham, Greater Manchester, England

Heron Mill is a cotton spinning mill in Hollinwood, Oldham, Greater Manchester. It was designed by architect P. S. Stott and was constructed in 1905 by the Heron Mill Company Ltd next to Durban Mill. It was taken over by the Lancashire Cotton Corporation in the 1930s and passed to Courtaulds in 1964. Production ended in 1960, and it was used by Courtaulds for offices, warehousing, and some experimental fabric manufacture. Courtaulds occupation ended in 1994.

<span class="mw-page-title-main">Newby Mill, Shaw</span> Cotton mill in Greater Manchester, England

Elm Mill, was a four-storey cotton spinning mill in Shaw and Crompton, Greater Manchester, England. It was built in 1890 for the Elm Spinning Company Ltd., and was called Elm Mill until it closed in 1928. It was revived by the Lancashire Cotton Corporation in 1929 and called Newby Mill. LCC and all their assets passed to Courtaulds in 1964. Production at Newby finished in 1970, and it was used for warehousing. Subsequently, named Shaw No 3 Mill, it became part of Littlewood's Shaw National Distribution Centre. It was demolished to make way for housing in 2022.

<span class="mw-page-title-main">Ellenroad Mill</span> Cotton mill in Newhey, Milnrow, Rochdale, England

Ellenroad Mill was a cotton spinning mill in Newhey, a village in the Milnrow area of Rochdale, England. It was built as a mule spinning mill in 1890 by Stott and Sons and extended in 1899. It was destroyed by fire on 19 January 1916. When it was rebuilt, it was designed and equipped as a ring spinning mill.

<span class="mw-page-title-main">Pear New Mill</span>

Pear New Mill is a former Edwardian cotton spinning mill on the northern bank of the River Goyt in Bredbury, Stockport, Greater Manchester, England. It is a Grade II* listed building.

<span class="mw-page-title-main">Swan Lane Mills</span>

Swan Lane Mills is a former cotton mill complex in Bolton, Greater Manchester. All three mills are Grade II* listed buildings. The mills were designed by Stott and Sons of Oldham. When completed, the double mill was the largest spinning mill in the world. It was granted Grade II* listed status on 26 April 1974. Number 3 Mill was separately listed as Grade II* on the same day.

References

  1. 1 2 Roberts, A S (1921). Arthur Robert's Engine List. Arthur Roberts Black Book. One guy from Barlick-Book Transcription. Archived from the original on 23 July 2011. Retrieved 11 January 2009.
  2. 1 2 3 Gurr, Duncan; Hunt, Julian (1998), The Cotton Mills of Oldham, Oldham Education & Leisure, p. 40, ISBN   0-902809-46-6, archived from the original on 18 July 2011, retrieved 26 September 2009
  3. ↑ "Historic mill blaze probe begins", BBC News, 22 April 2009
  4. ↑ Oehlke, Andreas, "Die Chemnitzer Aktienspinnnerei als Beispiel für eine Double Mill", Cotton Mills for the Continent (in German)
  5. ↑ Freeze, Karen (2007), "Innovation in Communist Europe" (PDF), Business and Economic History On-Line, University of Washington: Ellison Centre
  6. ↑ "Four held after kitchen firm raid", BBC News, 29 November 2006
  7. ↑ Vance Miller ordered to withdraw mini motos, oldham.gov.uk, 21 February 2007, archived from the original on 28 September 2007, retrieved 27 July 2007
  8. 1 2 Andrew Penman, "Huge blaze destroys factory of kitchen conman Vance Miller", Daily Mirror, MGN, retrieved 23 April 2009
  9. ↑ Britton, Paul (21 April 2009), Blaze Wrecks Kitchen Trader's Mill, Manchester Evening News , retrieved 21 April 2009
  10. ↑ Abbit, Beth (30 September 2016). "Pictures show inside of Oldham mill badly damaged in fire". Manchester Evening News. Retrieved 15 December 2016.
  11. 1 2 3 "People could have been sleeping in Oldham mill destroyed by huge fire". Manchester Evening News. 15 December 2016.
  12. 1 2 3 "Demolition begins at fire-hit Oldham mill". BBC News. 16 December 2016.
  13. ↑ "Oldham Maple Mill fire: Building 'still dangerous'". BBC News. 15 December 2016.
  14. 1 2 "50 firefighters remain at scene of Maple Mill fire as demolition work set to begin". Manchester Evening News. 16 December 2016.
  15. 1 2 "People could have been sleeping in huge mill gutted by fire". Manchester Evening News. 15 December 2016.
  16. ↑ "Fire crews leave Maple Mill in Oldham - nine days after huge blaze". Manchester Evening News. 24 December 2016.
This page is based on this Wikipedia article
Text is available under the CC BY-SA 4.0 license; additional terms may apply.
Images, videos and audio are available under their respective licenses.