Adverse yaw is the natural and undesirable tendency for an aircraft to yaw in the opposite direction of a roll. It is caused by the difference in lift and drag of each wing. The effect can be greatly minimized with ailerons deliberately designed to create drag when deflected upward and/or mechanisms which automatically apply some amount of coordinated rudder. As the major causes of adverse yaw vary with lift, any fixed-ratio mechanism will fail to fully solve the problem across all flight conditions and thus any manually operated aircraft will require some amount of rudder input from the pilot in order to maintain coordinated flight.
Adverse yaw was first experienced by the Wright brothers when they were unable to perform controlled turns in their 1901 glider which had no vertical control surface. Orville Wright later described the glider's lack of directional control.[1]
Causes
Adverse yaw is a secondary effect of the inclination of the lift vectors on the wing due to its rolling velocity and of the application of the ailerons.[2]:327 Some pilot training manuals focus mainly on the additional drag caused by the downward-deflected aileron[3][4] and make only brief[5] or indirect[6] mentions of roll effects. In fact the rolling of the wings usually causes a greater effect than the ailerons.[8] Assuming a roll rate to the right, as in the diagram, the causes are explained as follows:
Lift vector deflection during rolling
During a positive rolling motion, the left wing moves upward. If an aircraft were somehow suspended in air with no motion other than a positive roll, then from the point of view of the left wing, air will be coming from above and striking the upper surface of the wing. Thus, the left wing will experience a small amount of oncoming airflow merely from the rolling motion. This can be conceptualized as a vector originating from the left wing and pointing towards the oncoming air during the positive roll, i.e. perpendicularly upwards from the left wing's surface. If this positive-rolling aircraft were additionally moving forward in flight, then the vector pointing towards the oncoming air will be mostly forward due to forward-moving flight, but also slightly upward due to the rolling motion. This is the dashed vector coming from the left wing in the diagram.
Thus, for the left wing of a forward-moving aircraft, a positive roll causes the oncoming air to be deflected slightly upwards. Equivalently, the left wing's effective angle of attack is decreased due to the positive roll.[2]:361 By definition, lift is perpendicular to the oncoming flow.[2]:18 The upward deflection of oncoming air causes the lift vector to be deflected backward. Conversely, as the right wing descends, its vector pointing towards the oncoming air is deflected downward and its lift vector is deflected forward. The backward deflection of lift for the left wing and the forward deflection of lift for the right wing results in an adverse yaw moment to the left, opposite to the intended right turn. This adverse yaw moment is present only while the aircraft is rolling relative to the surrounding air, and disappears when the aircraft's bank angle is steady.
Induced drag
Initiating a roll to the right requires a briefly greater lift on the left than the right. This also causes a greater induced drag on the left than the right, which further adds to the adverse yaw, but only briefly. Once a steady roll rate is established the left/right lift imbalance dwindles,[2]:351 while the other mechanisms described above persist.
Profile drag
The downward aileron deflection on the left increases the airfoil camber, which will typically increase the profile drag. Conversely, the upward aileron deflection on the right will decrease the camber and profile drag. The profile drag imbalance adds to the adverse yaw. A Frise aileron reduces this imbalance drag, as described further below.
Minimizing the adverse yaw
There are a number of aircraft design characteristics which can be used to reduce adverse yaw to ease the pilot workload:
Yaw stability
A strong directional stability is the first way to reduce adverse yaw.[7] This is influenced by the vertical tail moment (area and lever arm about gravity center).
Lift coefficient
As the tilting of the left/right lift vectors is the major cause to adverse yaw, an important parameter is the magnitude of these lift vectors, or the aircraft's lift coefficient to be more specific. Flight at low lift coefficient (or high speed compared to minimum speed) produces less adverse yaw.[2]:365
Aileron to rudder mixing
As intended, the rudder is the most powerful and efficient means of managing yaw but mechanically coupling it to the ailerons is impractical. Electronic coupling is commonplace in fly-by-wire aircraft.
Differential aileron deflection
Illustration of a Differential aileron
The geometry of most aileron linkages can be configured so as to bias the travel further upward than downward. By excessively deflecting the upward aileron, profile drag is increased rather than reduced and separation drag further aids in producing drag on the inside wing, producing a yaw force in the direction of the turn. Though not as efficient as rudder mixing, aileron differential is very easy to implement on almost any airplane and offers the significant advantage of reducing the tendency for the wing to stall at the tip first by limiting the downward aileron deflection and its associated effective increase in angle of attack.
Most airplanes use this method of adverse yaw mitigation — particularly noticeable on one of the first well-known aircraft to ever use them, the de Havilland Tiger Moth training biplane of the 1930s — due to the simple implementation and safety benefits.
Frise ailerons
Illustration of a Frise aileron
Frise ailerons are designed so that when up aileron is applied, some of the forward edge of the aileron will protrude downward into the airflow, causing increased drag on this (down-going) wing. This will counter the drag produced by the other aileron, thus reducing adverse yaw.
Unfortunately, as well as reducing adverse yaw, Frise ailerons will increase the overall drag of the aircraft much more than applying rudder correction. Therefore, they are less popular in aircraft where minimizing drag is important (e.g. in a glider).
Note: Frise ailerons were primarily designed to reduce roll control forces. Contrary to the illustration, the aileron leading edge is in fact rounded to prevent flow separation and flutter at negative deflections.[9] That prevents important differential drag forces.
Roll spoilers
On large aircraft where rudder use is inappropriate at high speeds or ailerons are too small at low speeds, roll spoilers (also called spoilerons) can be used to minimise adverse yaw or increase roll moment. To function as a lateral control, the spoiler is raised on the down-going wing (up aileron) and remains retracted on the other wing. The raised spoiler increases the drag, and so the yaw is in the same direction as the roll.[10]
References and notes
Collection of balanced-aileron test data, F.M. Rogallo, Naca WR-L 419
↑ "How we invented the airplane", Orville Wright, page 16
1 2 3 4 5 Perkins, Courtland; Hage, Robert (1949). Airplane performance, stability and control. John Wiley and Sons. ISBN0-471-68046-X.
1 2 Langewiesche, Wolfgang (1944). Stick and Rudder. McGraw-Hill. pp. 163–165. ISBN0-07-036240-8.
↑ 'An expert will object here and point out that the ailerons cannot be held wholly responsible for the adverse yaw effect; that some of this adverse yawing tendency is due simply to the rolling motion of the wings and would persist no matter what device might cause the wings to roll. But the explanation just given answers the purposes of the pilot. Even though it does not tell the whole truth, it tells truth, and it has the advantage that it can be "shown."'[3]
↑ 'The adverse yaw is a result of differential drag and the slight difference in the velocity of the left and right wings.'[4]
1 2 Airplane Stability and Control, Abzug and Larrabee, page 64. "Adverse yaw must be overcome by good directional stability complemented by rudder deflection".
↑ 'for normal wing plan forms with aspect ratios above about 6, adverse yaw is actually dominated by the aerodynamic yawing moment due to rolling'[7]
↑ Wind-tunnel tests of ailerons at various speeds, W. Letko and W.B. Kemp, NACA WR-L 325
↑ Oxford Aviation Academy (2007), JAA ATPL 13: Principles of Flight, Transair
Related Research Articles
A fluid flowing around an object exerts a force on it. Lift is the component of this force that is perpendicular to the oncoming flow direction. It contrasts with the drag force, which is the component of the force parallel to the flow direction. Lift conventionally acts in an upward direction in order to counter the force of gravity, but it can act in any direction at right angles to the flow.
An aileron is a hinged flight control surface usually forming part of the trailing edge of each wing of a fixed-wing aircraft. Ailerons are used in pairs to control the aircraft in roll, which normally results in a change in flight path due to the tilting of the lift vector. Movement around this axis is called 'rolling' or 'banking'.
Flight dynamics is the science of air vehicle orientation and control in three dimensions. The three critical flight dynamics parameters are the angles of rotation in three dimensions about the vehicle's center of gravity (cg), known as pitch, roll and yaw.
In flight dynamics a spin is a special category of stall resulting in autorotation about the aircraft's longitudinal axis and a shallow, rotating, downward path approximately centred on a vertical axis. Spins can be entered intentionally or unintentionally, from any flight attitude if the aircraft has sufficient yaw while at the stall point. In a normal spin, the wing on the inside of the turn stalls while the outside wing remains flying. It is possible for both wings to stall, but the angle of attack of each wing, and consequently its lift and drag, are different.
Aircraft flight control surfaces are aerodynamic devices allowing a pilot to adjust and control the aircraft's flight attitude.
In aeronautics, dihedral is the angle between the left and right wings of an aircraft. "Dihedral" is also used to describe the effect of sideslip on the rolling of the aircraft.
Control reversal is an adverse effect on the controllability of aircraft. The flight controls reverse themselves in a way that is not intuitive, so pilots may not be aware of the situation and therefore provide the wrong inputs; in order to roll to the left, for instance, they have to push the control stick to the right, the opposite of the normal direction.
The hammerhead turn, stall turn, or Fieseler is an aerobatics turn-around maneuver.
A slip is an aerodynamic state where an aircraft is moving somewhat sideways as well as forward relative to the oncoming airflow or relative wind. In other words, for a conventional aircraft, the nose will be pointing in the opposite direction to the bank of the wing(s). The aircraft is not in coordinated flight and therefore is flying inefficiently.
Dutch roll is a type of aircraft motion consisting of an out-of-phase combination of "tail-wagging" (yaw) and rocking from side to side (roll). This yaw-roll coupling is one of the basic flight dynamic modes. This motion is normally well damped in most light aircraft, though some aircraft with well-damped Dutch roll modes can experience a degradation in damping as airspeed decreases and altitude increases. Dutch roll stability can be artificially increased by the installation of a yaw damper. Wings placed well above the center of gravity, sweepback and dihedral wings tend to increase the roll restoring force, and therefore increase the Dutch roll tendencies; this is why high-winged aircraft often are slightly anhedral, and transport-category swept-wing aircraft are equipped with yaw dampers. A similar phenomenon can happen in a trailer pulled by a car.
Aircraft flight mechanics are relevant to fixed wing and rotary wing (helicopters) aircraft. An aeroplane, is defined in ICAO Document 9110 as, "a power-driven heavier than air aircraft, deriving its lift chiefly from aerodynamic reactions on surface which remain fixed under given conditions of flight".
A vertical stabilizer or tail fin is the static part of the vertical tail of an aircraft. The term is commonly applied to the assembly of both this fixed surface and one or more movable rudders hinged to it. Their role is to provide control, stability and trim in yaw. It is part of the aircraft empennage, specifically of its stabilizers.
The critical engine of a multi-engine fixed-wing aircraft is the engine that, in the event of failure, would most adversely affect the performance or handling abilities of an aircraft. On propeller aircraft, there is a difference in the remaining yawing moments after failure of the left or the right (outboard) engine when all propellers rotate in the same direction due to the P-factor. On turbojet and turbofan twin-engine aircraft, there usually is no difference between the yawing moments after failure of a left or right engine in no-wind condition.
In aeronautics, spoilerons are spoilers that can be used asymmetrically as flight control surfaces to provide roll control.
A barrel roll is an aerial maneuver in which an airplane makes a complete rotation on both its longitudinal and lateral axes, causing it to follow a helical path, approximately maintaining its original direction. It is sometimes described as a "combination of a loop and a roll". The g-force is kept positive on the object throughout the maneuver, commonly between 2 and 3g, and no less than 0.5g. The barrel roll is commonly confused with an aileron roll.
In a straight flight, the tail of the airplane aligns the fuselage into the relative wind. However, in the beginning of a turn, when the ailerons are being applied in order to bank the airplane, the ailerons also cause an adverse yaw of the airplane. For example, if the airplane is rolling clockwise, the airplane yaws to the left. It assumes a crab-like attitude relative to the wind. This is called a slip. The air is flowing crosswise over the fuselage. In order to correct this adverse slip, the pilot must apply rudder. If the pilot applies too much rudder, the airplane will then slip to the other side. This is called a skid.
In aviation, coordinated flight of an aircraft is flight without sideslip.
Balanced rudders are used by both ships and aircraft. Both may indicate a portion of the rudder surface ahead of the hinge, placed to lower the control loads needed to turn the rudder. For aircraft the method can also be applied to elevators and ailerons; all three aircraft control surfaces may also be mass balanced, chiefly to avoid aerodynamic flutter.
Radio-controlled aerobatics is the practice of flying radio-controlled aircraft in maneuvers involving aircraft attitudes that are not used in normal flight.
A slow roll is a roll made by an airplane, in which the plane makes a complete rotation around its roll axis while keeping the aircraft flying a straight and level flightpath. A slow roll is performed more slowly than an aileron roll; although it is not necessarily performed very slowly, it is performed slowly enough to allow the pilot to maintain balance, keeping a steady flightpath, pitch angle, and height (altitude) throughout the maneuver. The maneuver is performed by rolling the airplane at a controlled rate with the ailerons, and moving the elevators and rudder in opposition, or "cross-controlling," to keep the plane on a steady, level flightpath.
This page is based on this Wikipedia article Text is available under the CC BY-SA 4.0 license; additional terms may apply. Images, videos and audio are available under their respective licenses.
