Baker-McMillan Cadet

Last updated

Cadet
Baker-McMillen Cadet II Aero Digest May,1930.jpg
Cadet II
Role Glider
National origin United States
Manufacturer Baker-McMillan
Designer Frank R. Gross
First flight1929
Introduction1929
StatusProduction completed
Primary userMostly gliding clubs
Produced1929-circa 1930
Number builtat least 30

The Baker-McMillan Cadet is an American, high-wing, strut-braced, open-cockpit, single-seat glider that was designed in 1929 by Frank R. Gross and produced by Baker-McMillan (Different sources variously spell the company name Baker-MacMillen, Baker Macmillen or Baker MacMillen). [1] [2]

Contents

Design and development

The Cadet was designed by Dr. Gross, a former member of the Akaflieg Darmstadt, in 1929 as an improvement over the primary gliders then in use and as an aircraft that would offer soaring capability. [1] [2]

The Cadet is built with a steel tube fuselage and a wooden wing that is supported by dual parallel struts, with jury struts. The tail is a wire-braced wooded structure. The whole aircraft is covered in doped aircraft fabric covering. [1] [2]

At least 30 and perhaps as many as 40 Cadets were constructed. [2]

Operational history

The Cadet was the first glider to be flown at Elmira, New York after Wolfgang Klemperer, Warren Eaton and Earl Southee surveyed the area and determined it had potential for soaring flights. One flight was flown by Jack O'Meara, a factory pilot for Baker-McMillan, who had a flight of one hour and 38 minutes from Elmira's South Mountain. [1] [2]

One Cadet was flown from water on twin floats. On another occasion four Cadets were towed aloft at the same time and released by a Goodyear Blimp over Akron, Ohio. [1] [2]

In March 2011 two Cadets remained on the Federal Aviation Administration registry. [3]

Aircraft on display

Specifications (Cadet)

Baker-McMillen Cadet II 3-view drawing from Aero Digest October,1930 Baker-McMillen Cadet II 3-view Aero Digest October,1930.png
Baker-McMillen Cadet II 3-view drawing from Aero Digest October,1930

Data from Sailplane Directory and Soaring [1] [2]

General characteristics

Performance

See also

Related Research Articles

<span class="mw-page-title-main">Schweizer SGU 1-7</span> Type of aircraft

The Schweizer SGU 1-7 is an American Open Class, single-seat, high-wing strut braced glider built by Schweizer Metal Aircraft Company of Elmira, New York.

<span class="mw-page-title-main">Schweizer SGS 2-8</span> Type of aircraft

The Schweizer SGS 2-8 is an American two-seat, mid-wing, strut-braced, training glider built by Schweizer Aircraft of Elmira, New York.

<span class="mw-page-title-main">Schweizer SGU 1-19</span> American family of gliders

The Schweizer SGU 1-19 and Schweizer SGU 1-20 are a family of United States single-seat, high-wing, strut-braced, utility gliders built by Schweizer Aircraft of Elmira, New York.

<span class="mw-page-title-main">Schweizer SGU 2-22</span> American glider

The Schweizer SGU 2-22 is an American two-seat, high-wing, strut-braced, training glider built by Schweizer Aircraft of Elmira, New York.

<span class="mw-page-title-main">Slingsby Tandem Tutor</span> British two-seat glider, 1949

The T.31 Tandem Tutor is a British military training glider, designed and built by Slingsby and used in large numbers by the Air Training Corps between 1951 and 1986.

<span class="mw-page-title-main">Nelson Dragonfly</span> American motorglider

The Bowlus/Nelson BB-1 Dragonfly is an American, two seat, strut-braced, high-wing motor glider that was developed from the Bowlus BA-100 Baby Albatross glider by Hawley Bowlus.

<span class="mw-page-title-main">Franklin PS-2</span> American glider

The Franklin PS-2 is an American, high-wing, strut-braced, single seat, glider that was designed by R. E. Franklin and produced by the Franklin Glider Corporation starting in 1930.

The Scanlan SG-1A is an American, single seat, pod-and-boom, high-wing, strut-braced glider that was designed by Thomas W. Scanlan in 1970 and sold in the form of plans for amateur construction.

<span class="mw-page-title-main">Bock 1</span> American glider

The Bock 1 is an American high-wing, strut-braced single-seat glider that was designed by John W. Bock of Long Beach, California.

The Cadet UT-1 is an American single-seat, high wing, strut-braced glider modified by Alex Dawydoff from the original Slingsby Kirby Cadet design and produced by Cadet Aeronautics.

The Bennett-Carter CBS-1 Dottie S is an American high-wing, strut-braced single-seat glider that was designed by George Bennett and Richard Carter and first flown in 1958.

<span class="mw-page-title-main">Haufe Dale Hawk 2</span> American glider

The Haufe Dale Hawk 2 is an American high-wing, strut-braced, single-seat glider that was designed and built by Walter Haufe and Leland Hanselman.

<span class="mw-page-title-main">Jongblood Primary</span> American homebuilt glider

The Jongblood Primary is an American single-seat, high-wing, strut-braced primary glider designed by Mike Jongblood of southern California and first flown in 1967. The aircraft is unusual in that primary gliders went out of fashion in the 1930s and few have been built since.

<span class="mw-page-title-main">Kennedy K-W</span> American glider

The Kennedy K-W is an American high-wing, strut-braced, single-seat glider that was designed by Harold Kennedy of Dodge City, Kansas, with assistance from Floyd Watson. The aircraft is notable for being assembled from certified powered aircraft components and also for having had an in-flight break-up.

<span class="mw-page-title-main">Midwest MU-1</span> Type of aircraft

The Midwest MU-1 was an American single-seat, high-wing, strut-braced utility glider that was designed by Arthur B. Schultz in the 1930s.

The Schultz Nucleon is an American high-wing strut-braced, single-seat glider that was designed and constructed by Arthur B. Schultz.

<span class="mw-page-title-main">Hütter Hü 17</span> Utility train glider

The Hütter Hü 17, is a German high-wing, strut-braced, single-seat, utility training glider that was designed by brothers Ulrich Hütter and Wolfgang Hütter in the 1930s.

<span class="mw-page-title-main">Schleicher Condor</span> German glider family designed by Heini Dittmar, 1932

The Schleicher Condor, also referred to as the Dittmar Condor, is a series of German high-wing, single and two-seat, gull winged, gliders that were designed by Heini Dittmar in the 1930s, produced in small quantities before the Second World War, produced again between 1952 and 1955 by Alexander Schleicher GmbH & Co and also by Ferdinand Schmetz.

The Kelsey K-16 is an American, strut-braced, high-wing, two-seat, glider that was designed and constructed by William Frank Kelsey of Salt Lake City, Utah.

The Gross Sky Ghost is an American high-wing, strut-braced, two-seat, glider that was designed by Frank R. Gross.

References

  1. 1 2 3 4 5 6 Activate Media (2006). "Cadet Baker-McMillen". Archived from the original on April 5, 2012. Retrieved March 30, 2011.
  2. 1 2 3 4 5 6 7 8 Said, Bob: 1983 Sailplane Directory, Soaring Magazine , page 9. Soaring Society of America, November 1983. USPS 499-920
  3. ↑ Federal Aviation Administration (March 2011). "Make / Model Inquiry Results" . Retrieved March 30, 2011.
  4. ↑ National Soaring Museum (2011). "Sailplanes in Our Collection". Archived from the original on May 16, 2011. Retrieved February 26, 2011.
This page is based on this Wikipedia article
Text is available under the CC BY-SA 4.0 license; additional terms may apply.
Images, videos and audio are available under their respective licenses.