CVT4 Strale

Last updated
GP1
RoleCompetition glider
ManufacturerSoaring Centre of the Polytechnic of Turin (CVT)
DesignerAlberto & Pietro Morelli
First flightJuly 1961
Number built1
Developed from CVT2 Veltro

The CVT4 Strale (English: Arrow) was a one-off, experimental, high performance glider designed and built in Italy. Completed in 1961, it was a refined version of the earlier CVT2 Veltro.

Contents

Design and development

The Strale was a refinement of the pioneering CVT2 Veltro of 1954. The Veltro went from design commencement to completion in eight months; the Strale, started in 1955, was not finished until July 1961, even though the two aircraft had much in common. [1]

The main differences between the Veltro and the Strale were in the wing, even though these had a similar straight tapered plan and used the same laminar flow NACA airfoil sections. The Starle's wing was constructed, like that of the Veltro, around a forward main box spar and a lighter secondary spar aft but was in two rather than three parts. The outer span washout and the tip bodies were discarded. The span was increased by 1,080 mm (42.5 in), which raised the aspect ratio from 18 to 19.3. [1] Each aileron of the Strale was shortened by 900 mm (35.4 in) [2] and plywood covered, and the combined flaps/ airbrakes of the Veltro were discarded, replaced by spoilers. These were similar to those used on the CVT M-100S: mounted immediately behind the main spar at about one third span, each set consisted of five plates that rotated about chordwise axes out of the wing, each plate projecting both above and below. The two sets rotated in opposite directions [1] and proved to be very effective. [3]

The Strale was a high wing rather than shoulder wing design, reducing aerodynamic interference over the upper surface. It had a slightly deeper cockpit and a single wheeled version of the Veltro's trailing arm, retractable undercarriage, the wheel with its single shock absorber now totally within the fuselage after retraction. The slender rear fuselages and low T-tails of the two gliders were very similar, though the dorsal fin added after flight testing to the Veltro was more smoothly faired into the fin of the Strale. [3] The double slotted rudder was increased in area by about 11%, lowering its aspect ratio still further and making the overall fuselage length 130 mm (5.1 in) greater. [2]

The Strale made its first flight in July 1961 and after some testing took part in the Italian National Gliding Competition in Perugia early that August. [1] Like the Veltro, it was seen as an experimental aircraft and only one was built. [3]

Specifications

Data from The World's Sailplanes (1958) pp.152-5 [2]

General characteristics

Performance


Related Research Articles

The Akaflieg Darmstadt D-30 Cirrus was an aerodynamically advanced single seat sailplane with a very high aspect ratio wing and a pod and boom fuselage. Built in Germany just before World War II, it was intended as a record breaker and duly set a new world out-and-return distance record in 1938.

CVV-4 Pellicano

The CVV-4 Pellicano was a single seat Italian glider designed for a competition to select an aircraft for the 1940 Olympic Games. The DFS Olympia Meise was preferred to it after the trials in Italy in 1939.

The Ciani EC.37/53 Spillo or SSVV EC.37/53 Spillo was a single seat competition glider designed and built in Italy in the 1950s. It had the highest aspect ratio wing of any wooden glider. Only one was built.

The CVV1 Pinguino was a single seat, high performance glider designed and built in Italy in the mid-1930s, the first of a series of gliders from the Milan Polytechnic. It did not go into production.

The CVV 2 Asiago is a simple, single seat glider designed and built in Italy in the mid-1930s, the second of a series of gliders from the Milan Polytechnic and the first go into production.

The CVV 3 Arcore was a single seat competition glider designed and built in Italy in the late 1930s, a development of the CVV 1 Pinguino. It participated in several national gliding competitions in the short period before the outbreak of World War II.

The CVV 5 Papero was a single seat competition glider designed and built in Italy in the late 1930s, a development of the CVV 4 Pellicano.

The CVV 7 Pinocchio was a single seat competition glider designed and built in Italy, first flown in 1952 though designed in 1940. Only one was built.

CVV 8 Bonaventura

The CVV 8 Bonaventura was a two-seat competition glider designed and built in Italy during the 1950s. Fifteen were produced.

The Aeronautica Lombarda AL-3 was an Italian sailplane, designed and built in 1939 to take part in the Olympic sailplane competition. It did so but was not successful.

The Bonomi BS.11 Milano and BS.12 Roma were primary gliders designed and built in Italy in the 1930s. Only about six were produced.

The Tedeschi E.T.186 was a simple, single seat training glider built in Italy and first flown in 1947. Only one was constructed.

The Pagliani Vittoria was a single-seat glider built in Italy during Second World War. Only one was constructed.

The CAT 15 was a single-seat primary glider built in Italy just before the Second World War. Only one was constructed.

The CVT1 Zigilo was a single-seat, 12-metre-span (39 ft) Italian training glider designed and built in Italy in the 1950s. Only one was completed.

CVT2 Veltro

The CVT2 Veltro was an Italian competition glider built in the mid-1950s. Its advanced design incorporated a laminar flow wing, T-tail, retracting undercarriage and a reclining seat to reduce parasitic drag.

The Teichfuss Tenax was an Italian, one-off, single seat glider, designed and built by Luigi Treichfuss in 1926 and influenced by German developments.

The Teichfuss Nibio was an Italian single seat glider, designed by Luigi Teichfuss and flown in two versions around 1930.

The Teichfuss Cicogna was an Italian tailless single-seat motor glider designed by Luigi Teichfuss and flown in 1936.

The Teichfuss Astore was an Italian Intermediate single-seat trainer glider designed by Luigi Teichfuss and flown in 1936. Two were built.

References

  1. 1 2 3 4 5 Pedrielli, Vincenzo; Camastra, Francesco (2011). Italian Vintage Sailplanes. Königswinter: EQIP Werbung & Verlag GmbH. pp. 142–4. ISBN   9783980883894.
  2. 1 2 3 Wilkinson, K.G.; B.S. Shenstone (1958). The World's Sailplanes:Die Segelflugzeuge der Welt:Les Planeurs du Monde (in English, French, and German) (1st ed.). Zurich: Organisation Scientifique et Technique Internationale du Vol a Voile (OSTIV) and Schweizer Aero-Revue. pp. 151, 152–5.
  3. 1 2 3 Simons, Martin (2006). Sailplanes 1945-1965 (2nd revised ed.). Königswinter: EQIP Werbung & Verlag GmbH. pp.  166–8. ISBN   3 9807977 4 0.
  4. ↑ "CVT-4 Strale" . Retrieved 16 November 2013.
This page is based on this Wikipedia article
Text is available under the CC BY-SA 4.0 license; additional terms may apply.
Images, videos and audio are available under their respective licenses.