Channel allocation schemes

Last updated

In radio resource management for wireless and cellular networks, channel allocation schemes allocate bandwidth and communication channels to base stations, access points and terminal equipment. The objective is to achieve maximum system spectral efficiency in bit/s/Hz/site by means of frequency reuse, but still assure a certain grade of service by avoiding co-channel interference and adjacent channel interference among nearby cells or networks that share the bandwidth.

Contents

Channel-allocation schemes follow one of two types of strategy: [1]

  1. Fixed: FCA, fixed channel allocation: manually assigned by the network operator
  2. Dynamic:
    1. DCA, dynamic channel allocation
    2. DFS, dynamic frequency selection
    3. Spread spectrum

Static Channel Allocation

In Fixed Channel Allocation or Fixed Channel Assignment (FCA) each cell is given a predetermined set of frequency channels. FCA requires manual frequency planning, which is an arduous task in time-division multiple access (TDMA) and frequency-division multiple access (FDMA) based systems since such systems are highly sensitive to co-channel interference from nearby cells that are reusing the same channel. Another drawback with TDMA and FDMA systems with FCA is that the number of channels in the cell remains constant irrespective of the number of customers in that cell. This results in traffic congestion and some calls being lost when traffic gets heavy in some cells, and idle capacity in other cells.

If FCA is combined with conventional FDMA and perhaps or TDMA, a fixed number of voice channels can be transferred over the cell. A new call can only be connected by an unused channel. If all the channel are occupied than the new call is blocked in this system. There are however several dynamic radio-resource management schemes that can be combined with FCA. A simple form is traffic-adaptive handover threshold, implying that calls from cell phones situated in the overlap between two adjacent cells can be forced to make the handover to the cell with the lowest load for the moment. If FCA is combined with spread spectrum, the maximum number of channels is not fixed in theory, but in practice a maximum limit is applied, since too many calls would cause too high co-channel interference level, causing the quality to be problematic. Spread spectrum allows cell breathing to be applied, by allowing an overloaded cell to borrow capacity (maximum number of simultaneous calls in the cell) from a nearby cell that is sharing the same frequency.

FCA can be extended into a DCA system by using a borrowing strategy in which a cell can borrow channels from the neighboring cell which is supervised by Mobile Switching Center (MSC).

Dynamic Frequency Selection

Dynamic Frequency Selection (DFS) is a mechanism specified for wireless networks with non-centrally controlled access points, such as wireless LAN (commonly Wi-Fi). It is designed to prevent interference with other usages of the frequency band, such as military radar, satellite communication, and weather radar. [2] The access points would automatically select frequency channels with low interference levels. In case of wireless LAN standard, DFS was standardized in 2003 as part of IEEE 802.11h. Actual frequency band for DFS vary by jurisdiction. It is often enforced for the frequency bands used by Terminal Doppler Weather Radar [3] [4] and C-Band satellite communication. The misconfiguration of DFS had caused significant disruption in weather radar operation during early deployments of 5 GHz Wi-Fi in a number of countries in the world. [4] [5] For example, DFS is also mandated in the 5470-5725 MHz U-NII band for radar avoidance in United States. [6]

Dynamic Channel Allocation

A more efficient way of channel allocation would be Dynamic Channel Allocation or Dynamic Channel Assignment (DCA) in which voice channel are not allocated to cell permanently, instead for every call request base station request channel from MSC. The channel is allocated following an algorithm which accounts the following criteria:

It requires the MSC to collect real time data on channel occupancy, traffic distribution and Received Signal Strength Indications (RSSI). DCA schemes are suggested for TDMA/FDMA based cellular systems such as GSM, but are currently not used in any products.[ citation needed ] OFDMA systems, such as the downlink of 4G cellular systems, can be considered as carrying out DCA for each individual sub-carrier as well as each timeslot.

DCA can be further classified into centralized and distributed. Some of the centralized DCA schemes are:

DCA and DFS eliminate the tedious manual frequency planning work. DCA also handles bursty cell traffic and utilizes the cellular radio resources more efficiently. DCA allows the number of channels in a cell to vary with the traffic load, hence increasing channel capacity with little costs.

Spread spectrum

Spread spectrum can be considered as an alternative to complex DCA algorithms. Spread spectrum avoids cochannel interference between adjacent cells, since the probability that users in nearby cells use the same spreading code is insignificant. Thus the frequency channel allocation problem is relaxed in cellular networks based on a combination of spread spectrum and FDMA, for example IS95 and 3G systems. Spread spectrum also facilitate that centrally controlled base stations dynamically borrow resources from each other depending on the traffic load, simply by increasing the maximum allowed number of simultaneous users in one cell (the maximum allowed interference level from the users in the cell), and decreasing it in an adjacent cell. Users in the overlap between the base station coverage area can be transferred between the cells (called cell-breathing), or the traffic can be regulated by admission control and traffic-shaping.

However, spread spectrum gives lower spectral efficiency than non-spread spectrum techniques, if the channel allocation in the latter case is optimized by a good DCA scheme. Especially OFDM modulation is an interesting alternative to spread spectrum because of its ability to combat multipath propagation for wideband channels without complex equalization. OFDM can be extended with OFDMA for uplink multiple access among users in the same cell. For avoidance of inter-cell interference, FDMA with DCA or DFS is once again of interest. One example of this concept is the above-mentioned IEEE 802.11h standard. OFDM and OFDMA with DCA is often studied as an alternative for 4G wireless systems.

DCA on a packet-by-packet basis

In packet based data communication services, the communication is bursty and the traffic load rapidly changing. For high system spectrum efficiency, DCA should be performed on a packet-by-packet basis. Examples of algorithms for packet-by-packet DCA are Dynamic Packet Assignment (DPA), Dynamic Single Frequency Networks (DSFN) and Packet and resource plan scheduling (PARPS).

See also

Related Research Articles

<span class="mw-page-title-main">Code-division multiple access</span> Channel access method used by various radio communication technologies

Code-division multiple access (CDMA) is a channel access method used by various radio communication technologies. CDMA is an example of multiple access, where several transmitters can send information simultaneously over a single communication channel. This allows several users to share a band of frequencies. To permit this without undue interference between the users, CDMA employs spread spectrum technology and a special coding scheme.

<span class="mw-page-title-main">Digital enhanced cordless telecommunications</span> ITU Standard for cordless telephone systems

Digital enhanced cordless telecommunications (Digital European cordless telecommunications), usually known by the acronym DECT, is a standard primarily used for creating cordless telephone systems. It originated in Europe, where it is the common standard, replacing earlier cordless phone standards, such as 900 MHz CT1 and CT2.

<span class="mw-page-title-main">Time-division multiple access</span> Channel access method for networks using a shared communications medium

Time-division multiple access (TDMA) is a channel access method for shared-medium networks. It allows several users to share the same frequency channel by dividing the signal into different time slots. The users transmit in rapid succession, one after the other, each using its own time slot. This allows multiple stations to share the same transmission medium while using only a part of its channel capacity. Dynamic TDMA is a TDMA variant that dynamically reserves a variable number of time slots in each frame to variable bit-rate data streams, based on the traffic demand of each data stream.

In telecommunications and computer networks, a channel access method or multiple access method allows more than two terminals connected to the same transmission medium to transmit over it and to share its capacity. Examples of shared physical media are wireless networks, bus networks, ring networks and point-to-point links operating in half-duplex mode.

Frequency-division multiple access (FDMA) is a channel access method used in some multiple-access protocols. FDMA allows multiple users to send data through a single communication channel, such as a coaxial cable or microwave beam, by dividing the bandwidth of the channel into separate non-overlapping frequency sub-channels and allocating each sub-channel to a separate user. Users can send data through a subchannel by modulating it on a carrier wave at the subchannel's frequency. It is used in satellite communication systems and telephone trunklines.

<span class="mw-page-title-main">WiMAX</span> Wireless broadband standard

Worldwide Interoperability for Microwave Access (WiMAX) is a family of wireless broadband communication standards based on the IEEE 802.16 set of standards, which provide physical layer (PHY) and media access control (MAC) options.

4G is the fourth generation of broadband cellular network technology, succeeding 3G and preceding 5G. A 4G system must provide capabilities defined by ITU in IMT Advanced. Potential and current applications include amended mobile web access, IP telephony, gaming services, high-definition mobile TV, video conferencing, and 3D television.

<span class="mw-page-title-main">Cellular network</span> Communication network

A cellular network or mobile network is a telecommunications network where the link to and from end nodes is wireless and the network is distributed over land areas called cells, each served by at least one fixed-location transceiver. These base stations provide the cell with the network coverage which can be used for transmission of voice, data, and other types of content. A cell typically uses a different set of frequencies from neighboring cells, to avoid interference and provide guaranteed service quality within each cell.

This article discusses the mobile cellular network aspect of teletraffic measurements. Mobile radio networks have traffic issues that do not arise in connection with the fixed line PSTN. Important aspects of cellular traffic include: quality of service targets, traffic capacity and cell size, spectral efficiency and sectorization, traffic capacity versus coverage, and channel holding time analysis.

Spectral efficiency, spectrum efficiency or bandwidth efficiency refers to the information rate that can be transmitted over a given bandwidth in a specific communication system. It is a measure of how efficiently a limited frequency spectrum is utilized by the physical layer protocol, and sometimes by the medium access control.

<span class="mw-page-title-main">Statistical time-division multiplexing</span>

Statistical multiplexing is a type of communication link sharing, very similar to dynamic bandwidth allocation (DBA). In statistical multiplexing, a communication channel is divided into an arbitrary number of variable bitrate digital channels or data streams. The link sharing is adapted to the instantaneous traffic demands of the data streams that are transferred over each channel. This is an alternative to creating a fixed sharing of a link, such as in general time division multiplexing (TDM) and frequency division multiplexing (FDM). When performed correctly, statistical multiplexing can provide a link utilization improvement, called the statistical multiplexing gain.

<span class="mw-page-title-main">Orthogonal frequency-division multiple access</span> Multi-user version of OFDM digital modulation

Orthogonal frequency-division multiple access (OFDMA) is a multi-user version of the popular orthogonal frequency-division multiplexing (OFDM) digital modulation scheme. Multiple access is achieved in OFDMA by assigning subsets of subcarriers to individual users. This allows simultaneous low-data-rate transmission from several users.

The Unlicensed National Information Infrastructure (U-NII) radio band, as defined by the United States Federal Communications Commission, is part of the radio frequency spectrum used by WLAN devices and by many wireless ISPs.

<span class="mw-page-title-main">E-UTRA</span> 3GPP interface

E-UTRA is the air interface of 3rd Generation Partnership Project (3GPP) Long Term Evolution (LTE) upgrade path for mobile networks. It is an acronym for Evolved UMTS Terrestrial Radio Access, also known as the Evolved Universal Terrestrial Radio Access in early drafts of the 3GPP LTE specification. E-UTRAN is the combination of E-UTRA, user equipment (UE), and a Node B.

Maximum throughput scheduling is a procedure for scheduling data packets in a packet-switched best-effort network, typically a wireless network, in view to maximize the total throughput of the network, or the system spectral efficiency in a wireless network. This is achieved by giving scheduling priority to the least "expensive" data flows in terms of consumed network resources per transferred amount of information.

<span class="mw-page-title-main">Comparison of mobile phone standards</span>

This is a comparison of standards of mobile phones. A new generation of cellular standards has appeared approximately every tenth year since 1G systems were introduced in 1979 and the early to mid-1980s.

Dynamic Single Frequency Networks (DSFN) is a transmitter macrodiversity technique for OFDM based cellular networks.

Single-carrier FDMA (SC-FDMA) is a frequency-division multiple access scheme. It is also called linearly precoded OFDMA (LP-OFDMA). Like other multiple access schemes, it deals with the assignment of multiple users to a shared communication resource. SC-FDMA can be interpreted as a linearly precoded OFDMA scheme, in the sense that it has an additional DFT processing step preceding the conventional OFDMA processing.

<span class="mw-page-title-main">Dynamic frequency selection</span> Wifi channel allocation scheme

Dynamic Frequency Selection (DFS) is a channel allocation scheme specified for wireless LAN, commonly known as Wi-Fi. It is designed to prevent electromagnetic interference by avoiding co-channel operation with systems that predated Wi-Fi, such as military radar, satellite communication, and weather radar, and also to provide on aggregate a near-uniform loading of the spectrum. It was standardized in 2003 as part of IEEE 802.11h.

Radio resource management (RRM) is the system level management of co-channel interference, radio resources, and other radio transmission characteristics in wireless communication systems, for example cellular networks, wireless local area networks, wireless sensor systems, and radio broadcasting networks. RRM involves strategies and algorithms for controlling parameters such as transmit power, user allocation, beamforming, data rates, handover criteria, modulation scheme, error coding scheme, etc. The objective is to utilize the limited radio-frequency spectrum resources and radio network infrastructure as efficiently as possible.

References

  1. ↑ Guowang Miao, Jens Zander, Ki Won Sung, and Ben Slimane, Fundamentals of Mobile Data Networks, Cambridge University Press, ISBN   1107143217, 2016.
  2. ↑ Touw, Ron (Nov 16, 2016). "Radar Detection and DFS on MikroTik" (PDF). Radar Detect and DFS on MikroTik. MikroTik. Retrieved 4 December 2019– via YouTube. Decision ERC/DEC/(99)23 adds 5250-5350MHz and 5470-5725MHz with more Tx power but with the added caveat that DFS was required to protect legacy users (Military Radar and Satellite uplinks)
  3. ↑ Spain, Chris (July 10, 2014). "Winning Back the Weather Radio Channels Adds Capacity to 5GHz Wi-Fi Spectrum - Cisco Blogs". Cisco Blogs. Cisco. Retrieved 4 December 2019. The FCC ruling is re-opening the Terminal Doppler Weather Radar (TDWR) band (channels 120, 124, 128) with new test requirements for DFS protection.
  4. 1 2 Saltikoff, Elena (2016). "The Threat to Weather Radars by Wireless Technology". Bulletin of the American Meteorological Society. 97 (7): 1159–1167. doi: 10.1175/BAMS-D-15-00048.1 . ISSN   0003-0007. Since 2006, interference to C-band radars from RLAN is increasingly experienced by most OPERA members. ... The South African weather services initially tried to implement specific software filtering to improve the situation but then decided in 2011 to move its meteorological radar network to S band.
  5. ↑ Tristant, Philippe (16–18 September 2009). "RLAN 5 GHz interference to weather radars in Europe" (PDF). International Telecommunication Union. Retrieved 4 December 2019. More than 12 European countries experienced such interference cases (other cases have now been reported in number of countries in the world). Definitively harmful interference (in Hungary, the radar was declared as non-operational for more than 1 month)
  6. ↑ "5GHz agreement". Ntia.doc.gov. 2003-01-31. Retrieved 2012-08-29.
This page is based on this Wikipedia article
Text is available under the CC BY-SA 4.0 license; additional terms may apply.
Images, videos and audio are available under their respective licenses.