 | This article needs additional citations for verification .(June 2009) |
The Christie suspension is a suspension system developed by American engineer J. Walter Christie for his tank designs. It allowed considerably longer movement than conventional leaf spring systems then in common use, which allowed his tanks to have considerably greater cross-country speed. The system was first introduced on his M1928 design, and used on all[ citation needed ] of his designs until his death in 1944.
Christie advocated the use of lightweight tanks with long range and high speed, designed to penetrate enemy lines and attack their infrastructure and logistics capabilities.
A major problem with tanks in World War I was tracked suspension failure. Christie's first tank design of 1919 could be driven on its wheels to get to the starting point and then the tracks fitted before it went into action. The US Tank Corps ordered a single tank from Christie's company based on this design. The tank, known as the M1919, was delivered in early 1921 and tested until Christie proposed modifying it. The modifications added coil suspension to the front wheels and removed the turret - the armament being moved to the nose of the vehicle. The tank - now known as M1921 - was tested in 1922 and 1923 but considered lacking in maneuverability and internal space and so put into the Ordnance Museum at Aberdeen Proving Ground in 1924. [1]
His earlier designs in the 1920s were hampered by poor cross-country performance due to limited suspension capability. The major problem he faced was the limited vertical space for springs to move in: for a 25 cm movement it might need 50 or 75 cm of vertical space for the spring and strut, and his small designs did not offer such space.
In the late 1920s he devised a better solution. The solution was the addition of a bellcrank, which changed the direction of motion from vertical to horizontal. The road wheels were individually mounted on a pipe that could move vertically only, at the top of which the bell crank rotated the direction of motion to the rear. Springs were mounted on the end of the crank, and could be as long as needed, lying along the inside of the hull. The result was a substantial increase in range of motion, from only some 10 cm in his original designs, to 25 cm on the M1928, 35 cm on the M1930, and 60 cm on the M1932.
The M1928 weighed under 9 short tons (8.2 t) and had a 338 hp (252 kW) Liberty engine; this allowed it to reach 42 mph (68 km/h) on tracks and 70 mph (110 km/h) on its wheels. For context, this is comparable to a luxury/performance passenger car of the era, faster than a typical car, and faster even than a modern main battle tank that tops out at approximately 43 mph (70 km/h). The four sprung road wheels could move 11 inches on top of the "compression due to the weight of the vehicle". Although there was interest by the Army in the design, negotiations over the requirements were drawn out and a single Christie M1931 was delivered in March 1931 followed by an order for 7 more in June. These received official designation as "Convertible Medium Tank T3" and all seven were delivered by 1932. Four were given to the cavalry for testing. They had the main gun replaced with a heavy machine gun and were renamed "Combat Car T1". The crew of two and relatively light armour was insufficient for the infantry support function the tank was expected to have. The Army drew up a specification for an improved T3 but following disputes with Christie the order - for 5 of the "Convertible Medium Tank T3E2" was given to the American-La France company. [2]
The most famous Christie-based tanks, the Soviet BT tank series and the T-34, used coil springs mounted vertically (on the BT) or at a slight angle from vertical (the T-34).
Another feature of Christie's designs was the "convertible" drive: the ability to remove the tracks for road travel, allowing for higher speeds and better range, and reducing wear on the fragile caterpillar track systems of the 1930s. In one public test 1931 in Linden, NJ, Army officials clocked a Christie M1931 tank attaining 104 mph (167 km/h), making it the fastest tank in the world: a record many believe it still holds. [3] There were no return rollers for the upper track run; the tracks were supported by the road wheels. As with many track designs with center guide teeth, dual wheels were used, allowing the guide teeth to run between them.
Because large road wheels and "slack track" are characteristic of the Christie suspension, other designs with these features are sometimes misidentified as such. The real Christie suspension was used only[ citation needed ] on a few designs, notably the Soviet BT tanks and T-34, the British Cruiser tanks, including the A13s: Cruiser Mk III, Cruiser Mk IV, Covenanter, Crusader, Cromwell and the Comet, as well as some experimental Polish and Italian designs. Post-T-34 Soviet tanks, while remaining outwardly similar, have actually used torsion bar suspension, as did the German tanks with Heinrich Kniepkamp and Ernst Lehr's Schachtellaufwerke (interlaced running gear) suspension.
Later wartime developments simplified the suspension. By 1939, the Soviets found that the BT tank's convertible drive was an unnecessary complication which occupied valuable space in the tank, and the feature was dropped in the T-34. The original Christie suspension used large rubber-rimmed road wheels but wartime rubber shortages forced some T-34 factories to use wheels with sprung steel rims to be used instead. Most T-34s continued to be built with rubber-rimmed tires.
Continuous track or tracked treads are a system of vehicle propulsion used in tracked vehicles, running on a continuous band of treads or track plates driven by two or more wheels. The large surface area of the tracks distributes the weight of the vehicle better than steel or rubber tyres on an equivalent vehicle, enabling continuous tracked vehicles to traverse soft ground with less likelihood of becoming stuck due to sinking.
The BT tank was one of a series of Soviet light tanks produced in large numbers between 1932 and 1941. They were lightly armoured, but reasonably well-armed for their time, and had the best mobility of all contemporary tanks. The BT tanks were known by the nickname Betka from the acronym, or by its diminutive Betushka. The successor of the BT tanks was the famous T-34 medium tank, introduced in 1940, which would replace all of the Soviet fast tanks, infantry tanks, and light tanks in service.
Suspension is the system of tires, tire air, springs, shock absorbers and linkages that connects a vehicle to its wheels and allows relative motion between the two. Suspension systems must support both road holding/handling and ride quality, which are at odds with each other. The tuning of suspensions involves finding the right compromise. It is important for the suspension to keep the road wheel in contact with the road surface as much as possible, because all the road or ground forces acting on the vehicle do so through the contact patches of the tires. The suspension also protects the vehicle itself and any cargo or luggage from damage and wear. The design of front and rear suspension of a car may be different.
The cruiser tank was a British tank concept of the interwar period for tanks designed as modernised armoured and mechanised cavalry, as distinguished from infantry tanks. Cruiser tanks were developed after medium tank designs of the 1930s failed to satisfy the Royal Armoured Corps. The cruiser tank concept was conceived by Giffard Le Quesne Martel, who preferred many small light tanks to swarm an opponent, instead of a few expensive and unsatisfactory medium tanks. "Light" cruiser tanks carried less armour and were correspondingly faster, whilst "heavy" cruiser tanks had more armour and were slightly slower.
The M18 Hellcat is a tank destroyer used by the United States Army in World War II and the Korean War. Despite being equipped with the same main gun as some variants of the much larger Sherman tank, the M18 attained a much higher top speed of up to 55 mph (89 km/h) by keeping armor to a minimum, and using the innovative Torqmatic automatic transmission.
The Tank, Cruiser, Mk III, also known by its General Staff specification number A13 Mark I, was a British cruiser tank of the Second World War. It was the first British cruiser tank to use the Christie suspension system, which gave higher speeds and better cross-country performance; previous cruiser tank models had used triple wheeled bogie suspension.
The Cruiser Tank Mk IV was a British cruiser tank of the Second World War. It followed directly on from the Tank, Cruiser, Mk III. The first Mk IVs were Mk IIIs with extra armour fitted to the turret. Later Mk IVAs were built with the complete extra armour. The tank was used in France in 1940 and in the early part of the war in North Africa, before being withdrawn from service. A fast vehicle compared to other British tanks of the early part of the war, it was probably the best cruiser tank Britain had in 1940. In total, 955 of these tanks were built.
The Entwicklung series, more commonly known as the E-Series, was a late-World War II attempt by Nazi Germany to produce a standardised series of tank designs. There were to be standard designs in five different weight classes from which several specialised variants were to be developed. Design standardisation was envisioned to bring improvements over extreme complexity of previous tank designs that resulted in poor production rates and mechanical unreliability.
The M103 Heavy Tank was a heavy tank that served in the United States Army and the United States Marine Corps during the Cold War. Introduced in 1957, it served until 1974, by which time evolution of the concept of a main battle tank considered heavy tanks obsolete.
Horstmann suspension, also known as Horstman, Vickers-Horstman and rarely Slow Motion, is a type of tracked suspension devised by British tank designer John Carden and worked into a production design by engineer Sidney Horstmann.
The Type 95 Ha-Gō was a light tank used by the Empire of Japan during the Second Sino-Japanese War, at the Battles of Khalkhin Gol against the Soviet Union, and in the Second World War. It proved sufficient against infantry but was not effective against other tanks. Approximately 2,300 were produced, making it the most numerous Japanese armoured fighting vehicle of the Second World War.
A beam axle, rigid axle or solid axle is a dependent suspension design in which a set of wheels is connected laterally by a single beam or shaft. Beam axles were once commonly used at the rear wheels of a vehicle, but historically they have also been used as front axles in four-wheel-drive vehicles. In most automobiles, beam axles have been replaced with front (IFS) and rear independent suspensions (IRS).
John Walter Christie was an American engineer and inventor. He is known best for developing the Christie suspension system used for several World War II-era tank designs, most notably the Soviet BT and T-34 tanks series, and the United Kingdom Covenanter and Crusader Cruiser tanks, as well as the Comet heavy cruiser tank.
The 10TP was a Polish light cruiser tank that never progressed beyond the prototype stage. Though intended to contribute to the Polish armour development programme, the prototype was ultimately deemed unsuccessful. However, insights gained during testing informed the design of the subsequent 14TP model, which was never completed due to the outbreak of World War II.
The vertical volute spring suspension system is a type of vehicle suspension system which uses volute springs to compensate for surface irregularities. This type of the suspension system was mainly fitted on US and Italian tanks and armored fighting vehicles starting from throughout the 1930s up until after the end of the Second World War in 1945.
The Panzerkampfwagen III/IV was an experimental medium tank project undertaken by Germany during World War II. The tank was designed to use components of both the Panzer III and Panzer IV, in an attempt to integrate the two projects. The project was cancelled with only the blueprints developed, and no units were ever built.
T7 combat car was a prototype United States light tank design of the interwar period. It could run on rubber-tired wheels on roads or mount tracks for cross-country use. Although adequate in some areas, it lacked armament compared to contemporary vehicles and the project was cancelled after only one was built.
The Christie M1931, known as the Combat Car, T1 in US Cavalry use and Medium Tank, Convertible, T3 in Infantry branch, was a wheel-to-track tank designed by J. Walter Christie for the United States Army using Christie's ideas of an aero-engine and the novel Christie suspension to give high mobility.
The AMX 40 was a proposed French cruiser tank. It was intended to replace the SOMUA S35 and S40 tanks. The tank never went beyond design stage after the Fall of France.
The Christie Model 1919 was a prototype tank built by J. Walter Christie's Front Drive Motor Company in 1919.