DMM copper disc sitting on the turntable of a Neumann AM32 lacquer cutting lathe, built in the 1930s
Direct metal mastering (DMM) is an analogaudio disc mastering technique jointly developed by two German companies, Telefunken-Decca (Teldec) and Georg Neumann GmbH, toward the end of the 20th century after having seen the same technology used by RCA Princeton Labs for its SelectaVision videodiscs in the late-1970s.
Records manufactured with this technology are often marked by a "DMM" logo on the outer record sleeve. Many current production high quality pressings, as well as standard production LPs from the 1990s, only indicate its use by inscribing "DMM" in the lead-out groove area of the disc.
Neumann was responsible for manufacturing the actual DMM cutting equipment as part of its VMS80 series lathes.
Overview
The advantages of DMM (hard surface material) over acetate lacquer cutting (soft surface material) are both sonic and practical: because of the rigidity of the master disc medium, no groove wall bounce-back effects take place after the cutting has been completed. This preserves the original modulation details in the groove walls much better, especially those involved with sudden fast attacks (transients). The improved transient response, as well as the more linearphase response of DMM improve the overall stability and depth-of-field in the stereo image. In addition, disturbing adjacent groove print-through sounds (groove echoes) are reduced in DMM. Also, there is no need to rush the finalized master disc directly into a refrigerator for groove preservation, as in conventional lacquer disc cutting, before processing the master disc to produce matrices for the pressing of the records. Finally, only one electroplating generation is required to produce stampers, as opposed to three for conventional lacquer masters.
The cutting lathe for DMM engraves the audio signal directly onto a copper-plated master disc, instead of engraving the groove into a lacquer-coated aluminum disc. Examination of early DMM discs revealed what appeared to be a high frequency modulation in the groove, thought to be caused by the use of an ultrasonic carrier tone. In fact, there was no carrier tone and the modulation was simply caused by the vibration (squeal) of the cutter head as it was dragged through the copper disc.
The DMM copper master disc can be plated to produce the required number of stampers using the one-step plating process. Rather than having to electroform a master (or "father"), mother and then stampers (the traditional "three-step process"), the DMM copper disc serves as the 'mother". Bypassing the silvering process and two electroforming stages reduces the risk of introducing noise that can be generated in the electroforming (galvanic) process. In cases where hundreds of stampers may be required, the DMM disc is often used as a mandrel to electroform a master and mother, from which many stampers are then made. Chemical passivation of the metal surface of each part precludes "plating," so the parts can be mechanically separated from each other upon removal from the tank.
Since the sale of Neumann to German microphone manufacturer Sennheiser, Neumann no longer produces lathes or supplies parts. Since DMM was introduced at the very end of the vinyl age, only about 30 DMM lathes were ever made, compared to hundreds of lacquer lathes from various manufacturers, and about 10 of them were later converted to be used for conventional lacquer cutting. The lathes in use today are kept operational by independent service consultants, as well as cutting room personnel themselves, often by buying incomplete lathes and stripping them for parts.
The DMM specification also includes a profile for the pressing of 12-inch records. To the naked eye, this profile has no obvious contour on the face of the record giving the appearance of a totally flat-faced record. For the purpose of compression moulding, which is the process by which records are pressed, the face of the record does indeed have a contour and a cross-sectional view of a 12-inch record will reveal that it is wedge shaped from the centre to the edge. The lack of obvious contour in the groove area on the face of the record closely replicates the original disc surface and reduces playback errors. Pressing records with this profile was mandatory for a record to bear the "DMM" logo. DMM licensees that did not use this profile were unable to use the DMM logo on its products, but were of course free to use terms such as "Mastered on Copper" as did EMI Australia when not using the DMM-profiled moulds or when cutting a DMM master for another record manufacturer. The best example of a DMM pressing can usually be found on the Teldec (Germany) or EMI (UK) labels from the early 1980s.
The decline of vinyl records in favour of the compact disc, saw many Neumann VMS82 DMM lathes converted for cutting lacquer discs as few plants were able to process DMM masters and so many disc cutting facilities conformed to the industry standard – cutting on lacquer.
As of 2009 there are seven publicly-usable DMM cutting facilities left in the world, all located in Germany, Netherlands, or Czech Republic.[2] The US lost its last DMM cutting facility in 2005 with the demise of New York City-based record manufacturer Europadisk LLC. Europadisk's DMM lathe was sold at auction to the Church of Scientology for US $72,500.[citation needed]
The DMM concept was a spin-off of RCA's SelectaVision development of CED videodisc recording equipment both in Indianapolis as well as the David Sarnoff Research Facility in Princeton, New Jersey, who traded it to Teldec for other research it used in other capacities. After further development, Teldec attempted to sell its DMM technology back to RCA, however RCA was not interested. Therefore, as a result, all DMM titles from RCA and subsidiary labels were all mastered elsewhere.
Although Neumann produced, demonstrated and promoted a successful prototype CD Mastering unit for DMM, it never went into commercial production. Most of the remaining original spare parts were purchased from Neumann by the UK disc cutting consultant Sean Davies, who carried on repair maintenance of existing systems since Neumann stopped production.[3]
Advantages and disadvantages
The direct metal mastering technology addresses the lacquermastering technology's issue of pre-echoes during record play, caused by the cutting stylus unintentionally transferring some of the subsequent groove wall's impulse signal into the previous groove wall. In particular, a quiet passage followed by a loud sound often clearly revealed a faint pre-echo of the loud sound occurring 1.8 seconds ahead of time (the duration of one revolution at 33 rpm). This problem could also appear as post-echo, 1.8 seconds after a peak in volume.
Another improvement is noise reduction. The lacquer mastering method bears a higher risk of adding unwanted random noise to the recording, caused by the enclosure of small dust particles when spraying the silvering on the lacquer master, which is the necessary first step of the electroplating process for reproduction of the master disc. As the DMM master disc is already made of metal (copper), this step is not required, and its faults are avoided.
With the groove being cut straight into a metal foil, this removed a number of plating stages in the manufacturing process. This gave rise to more upper frequency levels and less surface noise. Additionally, groove pre-echo problems are significantly diminished. Bass is typically tight and well defined, even described as more accurate than the fat, mushy sound of lacquered vinyl pressings.
Because of the modulation arising from this cutting method, criticisms have arisen of the sound of such 'DMM' records. They are often labelled as bright or edgy.
DMM LP pressings are sometimes described as having a harshness or forwardness in the high frequencies. The fact the groove is cut to copper, a hard metal, and not to soft lacquer, nitrocellulose, supposedly endows DMM vinyl LP with a very different tonality to traditionally manufactured vinyl LP pressings. Direct metal mastering requires a radically different cutting angle than traditional (lacquer) cutting, almost 0 degrees.[1] However the playback cartridges will always have the standard playback angle of 15–22.5°. Thus, the DMM process includes electronic audio processing [4] so the records can be played with a standard cartridge despite having been cut at a substantially different angle. This electronic processing might account for the supposedly different high frequency "signature sound" of DMM records.
Digital recordings
A similar technique, developed by Teldec is used for digital records on CDs and DVDs.
UC compander, a noise reduction system undocumentedly used on many DMM vinyl records produced by several East-German record labels in the 1980s.
Related Research Articles
A phonograph record, a vinyl record, or simply a record or vinyl is an analog sound storage medium in the form of a flat disc with an inscribed, modulated spiral groove. The groove usually starts near the outside edge and ends near the center of the disc. The stored sound information is made audible by playing the record on a phonograph.
Modern cymbal making comprises many different techniques, from traditional hand methods to completely automated mass-production.
Mastering, a form of audio post production, is the process of preparing and transferring recorded audio from a source containing the final mix to a data storage device, the source from which all copies will be produced. In recent years, digital masters have become usual, although analog masters—such as audio tapes—are still being used by the manufacturing industry, particularly by a few engineers who specialize in analog mastering.
An acetate disc is a type of phonograph record generally used from the 1930s to the late 1950s for recording and broadcast purposes and sees limited use as of 2009. Despite their name, "acetate" discs do not contain any acetate.
The overwhelming majority of records manufactured have been of certain sizes, playback speeds, and appearance. However, since the commercial adoption of the gramophone record, a wide variety of records have also been produced that do not fall into these categories, and they have served a variety of purposes.
Compact disc manufacturing is the process by which commercial compact discs (CDs) are replicated in mass quantities using a master version created from a source recording. This may be either in audio form (CD-DA) or data form (CD-ROM). This process is used in the mastering of read-only compact discs. DVDs and Blu-rays use similar methods.
RIAA equalization is a specification for the recording and playback of phonograph records, established by the Recording Industry Association of America (RIAA). The purposes of the equalization are to permit greater recording times, to improve sound quality, and to reduce the groove damage that would otherwise arise during playback.
A matrix number is an alphanumeric code stamped or handwritten into the run-out groove area of a phonograph record. This is the non-grooved area between the end of the final band on a record's side and the label, also known as the run-off groove area, end-groove area, matrix area, or "dead wax".
The dbx Model 700 Digital Audio Processor was a professional audio ADC/DAC combination unit, which digitized a stereo analog audio input into a bitstream, which was then encoded and encapsulated in an analog composite video signal, for recording to tape using a VCR as a transport. Unlike other similar pieces of equipment like the Sony PCM-F1, the Model 700 used a technique called Companded Predictive Delta Modulation, rather than the now-common pulse-code modulation. At the time of its introduction in the mid-1980s the device was the first commercial product to use this method, although it had been proposed in the 1960s and prototyped in the late '70s.
A record press is a machine for manufacturing vinyl records. It is essentially a hydraulic press fitted with thin nickel stampers which are negative impressions of a master disc. Labels and a pre-heated vinyl patty are placed in a heated mold cavity. Two stampers are used, one for each of side of the disc. The record press closes under a pressure of about 150 tons. The process of compression molding forces the hot vinyl to fill the grooves in the stampers, and take the form of the finished record.
The LP is an analog sound storage medium, a phonograph record format characterized by: a speed of 33+1⁄3 rpm; a 12- or 10-inch diameter; use of the "microgroove" groove specification; and a vinyl composition disk. Introduced by Columbia Records in 1948, it was soon adopted as a new standard by the entire US record industry. Apart from a few relatively minor refinements and the important later addition of stereophonic sound in 1957, it remained the standard format for record albums, during a period in popular music known as the album era. Beginning in the late 1970s, LP sales began to decline because of the increasing popularity of Compact Cassettes, then in the 1980s of compact discs (CDs). By 1988, the latter format began to outsell LPs.
Dynaflex is a trademark for a thin, lightweight vinyl LP phonograph record introduced by RCA Records in late 1969. Rather than using the stiff plastic material used by conventional vinyl pressings, Dynaflex records used a softer, pliable formulation that allowed RCA to use less material, saving money and also making the record appear to lie flatter on turntables. At the time, as a cost-cutting measure, most industry record pressing plants were using recycled or "reground" vinyl, taking old and unsold records, cutting out the center with the paper labels, then melting the rest down and reusing the material to make new records. Such "reground" vinyl records typically sounded much noisier and scratchier when played than a record made from new or "virgin" vinyl; collectors noted that records pressed from "reground" vinyl sometimes had small remnants of paper labels or other materials embedded in them.
In the field of audio recording, an aluminum disc is a phonograph record made of bare aluminum, a medium introduced in the late 1920s for making one-off recordings. Although sometimes used for making amateur studio or home recordings or in coin-operated "record-your-voice" booths at fairs and arcades, during the first half of the 1930s bare aluminum discs were primarily used to record radio broadcasts for the private transcription disc archives of performers or sponsors.
Teldec is a German record label in Hamburg, Germany. Today the label is a property of Warner Music Group.
Zenith Records is a vinyl record pressing plant based in Melbourne, Australia, established in 2005.
In the production of phonograph records – discs that were commonly made of shellac, and later, vinyl – sound was recorded directly onto a master disc at the recording studio. From about 1950 on it became usual to have the performance first recorded on audio tape, which could then be processed and/or edited, and then dubbed on to the master disc.
Quality Record Pressings is a vinyl record pressing plant launched by music entrepreneur Chad Kassem in Salina, Kansas, United States in 2011. QRP sought to improve premier audiophile pressings, introducing innovations never before tried in the record pressing industry.
Electrical transcriptions are special phonograph recordings made exclusively for radio broadcasting, which were widely used during the "Golden Age of Radio". They provided material—from station-identification jingles and commercials to full-length programs—for use by local stations, which were affiliates of one of the radio networks.
A disc cutting lathe is a device used to transfer an audio signal to the modulated spiral groove of a blank master disc for the production of phonograph records. Disc cutting lathes were also used to produce broadcast transcription discs and for direct-to-disc recording.
This page is based on this Wikipedia article Text is available under the CC BY-SA 4.0 license; additional terms may apply. Images, videos and audio are available under their respective licenses.
