The Drift Sight was a bombsight developed by Harry Wimperis in 1916 for the Royal Naval Air Service (RNAS). It used a simple mechanical device to measure the wind speed from the air, and used that measurement to calculate the wind's effects on the trajectory of the bombs. The Drift Sight eliminated the need for a stopwatch to perform this calculation, as on earlier devices, and greatly eased the bomb aimer's workload.
The Drift Sight was quickly introduced into RNAS service and quickly thereafter by the Royal Flying Corps (RFC) as well. In British service, Wimperis' Course Setting Bomb Sight (CSBS) started replacing the Drift Sight in 1917, but it remained in widespread use in the US Army Air Service into the 1920s. In US use the Drift Sight is often referred to as the Wimperis sight, but this name is more commonly applied to the CSBS, especially in Commonwealth air forces.
Prior to the introduction of the Drift Sight, bombsights were generally very simple systems of very limited accuracy. The primary pre-World War I device in RNAS service was the "Lever Sight" which had to be held out of the cockpit in one hand by the pilot while flying the aircraft with the other. The Central Flying School bombsight (CFS) replaced this in 1915, but was difficult to install in the cockpit. The CFS was in turn replaced by the Equal Distance Sight (EDS) designed by in 1916 by Warrant Officer Scarff, better known for the Scarff ring. The EDS allowed the bomb run parameters to be entered once and then left the pilot free to fly the plane. [1]
Adjusting for the effects of wind was a difficult process. None of these sights had a way to calculate "drift", the sideways motion of the bombs due to wind. This meant the aircraft had to attack their targets along the wind line. [2] Even in this direction, the wind would cause the bombs to fall long or short. To correct for this, on an extended run the bomb aimer would measure their speed over the ground using a stopwatch, calculate the wind speed, and then adjust their aim point based on that speed and their current altitude. [3] This solution was difficult, time consuming, and prone to error.
In 1916, Henry Wimperis started design of a new bombsight, working in collaboration with Scarff. [2] His "Drift Sight" included a simple system for calculating the effects of wind.
This measurement was taken prior to the bomb run, using a secondary sighting system at the rear of the main bombsight. The pilot would first determine the direction of the wind, and estimated its speed. The estimated speed was dialled into the sight, which moved a metal rod at the back of the sight so it laid at an angle to the fuselage. The aircraft would then fly at right angles to the bomb line, which would cause the wind to push the aircraft sideways (unless this direction the aircraft is flying while doing this just happens to be directly upwind or downwind). Comparing the angle of motion of objects on the ground to the angle of the rod, the bomb aimer would adjust the angle of the rod until the two were equal. A scale at the end of the bar directly read the wind speed.
This adjustment also automatically moved sights at the front of the bombsight fore and aft, directly setting the bombsight to calculate the drift of the bombs due to the measured wind. Two sights were used, one for bombing directly upwind, and another for bombing directly downwind. The timing of the drop was set by dialling in the measured air speed, which moved the entire sighting system fore or aft, carrying the two "backsights" along with it (as well as the drift bar mechanism). Setting the altitude moved the foresight, below the backlights, setting the correct bombing angle.
The original design was only suitable for low-level use and was later known as the Low Height Drift Sight Mk. I. At higher altitudes the indicated airspeed - being measured by pitot tube instruments - was affected by differences in outside air pressure that rendered it increasingly inaccurate. (A correct ground speed is required for accurate bombing.) The Mk. IA was introduced for this role, including a simple adjustment between the airspeed and altitude settings that accounted for this effect. [2] A third version was also introduced for use by Navy airships, which worked at much lower speeds and also had the advantage of being able to directly measure the windspeed by throttling their engines until they lay still over the water. [3]
Although the Drift Sight was a significant improvement over earlier designs, it still required the aircraft to fly up or downwind on the final bomb run. For the RNAS this was a serious problem, as a submarine or ship would attempt to maneuver away if it spotted the attack, and thus upset the bomb run. Over land, as anti-aircraft guns grew more proficient, this became a serious concern as they would pre-sight for firing along the wind line, and using the bombsight under fire was difficult. [4] There were instructions on how to use the Drift Sight for cross-wind bombing, but this was complex and apparently rarely used. [3]
The Drift Sight was introduced in 1916, and the simplicity of the device in terms of manufacture and mounting to the aircraft allowed it to quickly equip RNAS forces. By 1917 it was in widespread use in the RNAS, and was selected for the Handley Page O/400 bomber in RFC service as well. However, Wimperis was well aware of the shortcomings of the Drift Sight in terms of flying along the wind line, and was already testing his solution, the Course Setting Bomb Sight. The CSBS was only slightly more complex than the Drift Sight to build, adding a compass and another adjustment to the sights to account for cross-drift. Hundreds were in use by 1918, and had supplanted the Drift Sight by the war's end. [2]
A major difference between the Drift Sight and CSBS was that the latter needed to sight below the aircraft, and was not as suitable for use on the side of the fuselage. This kept the Mk. IA in US Army Air Service use for some time, as they did not have dedicated bomber aircraft until after the war. Oddly, when development of new bombsights started in the 1920s, these were based on the Drift Sight design, not the CSBS. [5] The US Navy, contrarily, developed their Mk. III design from the CSBS, [6] and it was borrowed Mk. III sights that were used to sink the former German battleship Ostfriesland in 1921. [5]
The Drift Sight was mounted to the side of the aircraft using two brackets at the front and back of the sights. The forward bracket had a pivot point, and the rear a screw jack that rotated the entire sighting system up or down around the front bracket's pivot. This allowed fine adjustment of the levelling of the sight during flight to account for changes in trim, as measured on an attached spirit level. After making these adjustments the system was locked in position using wingnuts. This mounting system was common among early British bombsights, notably the Equal Distance Sight that led to the Drift Sight.
The main sighting system rode on two rods running fore and aft between the mounting brackets, allowing the bomb aimer to move it to a comfortable position for sighting. In the Equal Distance design, this movement was itself the main aiming mechanism, and could not be adjusted for ease of use as it was in the Drift Sight.
Sighting was accomplished in the manner of iron sights on rifles, and the Drift Sight used the same terminology of "foresight" and "backsight", although "lower" and "upper" would be more accurate physically. The fore and backsights were thin metal wires stretched across the opening of a C-shaped metal plate. The bombs were dropped when the wires of the foresight, backsight and target overlapped as seen from the bomb aimer's position. A separate "direction wire" ran fore-aft on a plate below the foresight, providing left-right aiming.
Altitude was set by moving a lever fore-and-aft against a scale, which rotated the foresight fore or aft, setting one half of the sight's bombing angle. Behind the altitude setting was an airspeed scale and a wheel to finely select the airspeed. This moved the backsights fore or aft to account for the other half of the sight's "range angle". In this respect the Drift Sight was similar to earlier bombsight designs.
Where it differed was in the addition of the "drift bar" setting at the extreme rear of the sighting system. The drift bar was a metal rod that extended rearward from the sight and was pivoted so it could rotated outward, away from the aircraft fuselage. Prior to the bomb run, the pilot or bomb aimer would dial in an estimated wind speed, which rotated the bar outward with increasing values. They would then look past the bar to any convenient objects on the ground, comparing its direction of motion to the line of the bar. Fine adjustments to the wind speed were made until the observed drift was directly along the line of the bar.
Changing the setting of the wind speed had the effect of moving the two backlights closer or further apart. This accounted for the effects of the wind on the trajectory of the bombs in addition to the airspeed setting. Two sights were used, one for bombing upwind and another for downwind.
As the Drift Sight only worked correctly if flying straight and level, the bombsight also includes two spirit levels.
An airfield traffic pattern is a standard path followed by aircraft when taking off or landing while maintaining visual contact with the airfield.
The Norden Mk. XV, known as the Norden M series in U.S. Army service, is a bombsight that was used by the United States Army Air Forces (USAAF) and the United States Navy during World War II, and the United States Air Force in the Korean and the Vietnam Wars. It was an early tachometric design, which combined optics, a mechanical computer, and an autopilot for the first time to not merely identify a target but fly the airplane to it. The bombsight directly measured the aircraft's ground speed and direction, which older types could only estimate with lengthy manual procedures. The Norden further improved on older designs by using an analog computer that continuously recalculated the bomb's impact point based on changing flight conditions, and an autopilot that reacted quickly and accurately to changes in the wind or other effects.
A total station or total station theodolite is an electronic/optical instrument used for surveying and building construction. It is an electronic transit theodolite integrated with electronic distance measurement (EDM) to measure both vertical and horizontal angles and the slope distance from the instrument to a particular point, and an on-board computer to collect data and perform triangulation calculations.
A fire-control system (FCS) is a number of components working together, usually a gun data computer, a director and radar, which is designed to assist a ranged weapon system to target, track, and hit a target. It performs the same task as a human gunner firing a weapon, but attempts to do so faster and more accurately.
Helicopter flight controls are used to achieve and maintain controlled aerodynamic helicopter flight. Changes to the aircraft flight control system transmit mechanically to the rotor, producing aerodynamic effects on the rotor blades that make the helicopter move in a desired way. To tilt forward and back (pitch) or sideways (roll) requires that the controls alter the angle of attack of the main rotor blades cyclically during rotation, creating differing amounts of lift at different points in the cycle. To increase or decrease overall lift requires that the controls alter the angle of attack for all blades collectively by equal amounts at the same time, resulting in ascent, descent, acceleration and deceleration.
A bombsight is a device used by military aircraft to drop bombs accurately. Bombsights, a feature of combat aircraft since World War I, were first found on purpose-designed bomber aircraft and then moved to fighter-bombers and modern tactical aircraft as those aircraft took up the brunt of the bombing role.
In aviation, a crosswind landing is a landing maneuver in which a significant component of the prevailing wind is perpendicular to the runway center line.
Autorotation is a state of flight in which the main rotor system of a helicopter or other rotary-wing aircraft turns by the action of air moving up through the rotor, as with an autogyro, rather than engine power driving the rotor. The term autorotation dates to a period of early helicopter development between 1915 and 1920, and refers to the rotors turning without the engine. It is analogous to the gliding flight of a fixed-wing aircraft. Some trees have seeds that have evolved wing-like structures that enable the seed to spin to the ground in autorotation, which helps the seeds to disseminate over a wider area.
The Stabilised Automatic Bomb Sight (SABS) was a Royal Air Force bombsight used in small numbers during World War II. The system worked along similar tachometric principles as the more famous Norden bombsight, but was somewhat simpler, lacking the Norden's autopilot feature.
The Mark XIV Bomb Sight was a bombsight developed by Royal Air Force (RAF) Bomber Command during the Second World War. It was also known as the Blackett sight after its primary inventor, P. M. S. Blackett. Production of a slightly modified version was also undertaken in the United States as the Sperry T-1, which was interchangeable with the UK-built version. It was the RAF's standard bombsight for the second half of the war.
The Carl Zeiss Lotfernrohr 7, or Lotfe 7, was the primary series of bombsights used in most Luftwaffe level bombers, similar to the United States' Norden bombsight, but much simpler to operate and maintain. Several models were produced and eventually completely replaced the simpler Lotfernrohr 3 and BZG 2 bombsights. The Lotfe 7C, appearing in January 1941, was the first one to have gyroscopic stabilization.
The Blackburn B.T.1 Beagle was a British single-engine, two-seat biplane bomber/torpedo aircraft from 1928. Designed to Air Ministry specifications which led to no contracts for any manufacturer, only one Beagle was built.
Harry Egerton WimperisWh.Sch was a British aeronautical engineer who acted as the Director of Scientific Research at the UK's Air Ministry prior to World War II. He is best known for his role in setting up the Committee for the Scientific Survey of Air Defence under Henry Tizard, which led directly to the development and introduction of radar in the UK. He is also known for the development of the Drift Sight and Course Setting Bomb Sight during World War I, devices that revolutionised the art of bombing.
The Course Setting Bomb Sight (CSBS) is the canonical vector bombsight, the first practical system for properly accounting for the effects of wind when dropping bombs. It is also widely referred to as the Wimperis sight after its inventor, Harry Wimperis.
Green Satin, also known as ARI 5851, was a Doppler radar system developed by the Royal Air Force as an air navigation aid. The system provided direct measures of the drift speed and direction, and thereby allowed accurate calculation of the winds aloft. These values were then fed into the Navigation and Bombing System.
The Low Level Bombsight, Mark III, sometimes known as the Angular Velocity Sight, was a Royal Air Force (RAF) bombsight designed for attacks by aircraft flying below 1,000 feet (300 m) altitude. It combined components of the Mark XIV bomb sight with a new mechanical computer. It featured a unique solution for timing the drop, projecting a moving display onto a reflector sight that matched the apparent motion of the target at the right instant.
A power-off accuracy approach, also known as a glide approach, is an aviation exercise used to simulate a landing with an engine failure. The purpose of this training technique is to better develop one's ability to estimate distance and glide ratios. The variation in each angle refers to the degrees an aircraft must turn to be aligned with the runway. Consideration of the wind and use of flaps are important factors in executing power-off accuracy approaches.
The Bombenzielanlage, sometimes referred to as the Bomb Ziel Automat (BZA), was a German World War II bombsight analog computer designed to calculate the precise release of bombs during dive-bombing. It was fitted to a number of aircraft types, including the Junkers Ju 88 and the Arado Ar 234. The unit controlled an aiming mark on sight in front of the pilot. The computer assessed the angle of dive, aircraft track, and altitude. The operator set other variables, such as barometric pressure, target altitude, airspeed and wind speed. During operation, the bomb(s) were released when an aiming mark coincided with the target.
The Bombsight, Pilot-Directing, Mark III was an inter-war era bombsight developed by the US Navy to equip its bomber aircraft. It was a development of the British Course Setting Bomb Sight, or CSBS, which had been introduced in UK service in early 1918 and was demonstrated to the Navy in Washington in May 1918. As the primary bombers in Navy service at the time were flying boats where the pilot and bombardier were separated, Mark III's primary change was to include an electrically driven pilot direction indicator.
The Estoppey D-series was a line of inter-war era bombsights developed by Georges Estoppey of the US Army Air Corps' McCook Field, starting with the D-1 of 1922. A key feature was the use of a pendulum to keep the bombsight correctly oriented towards the ground even as the aircraft maneuvered, and dashpots to keep it from swinging around in turbulence.