Drill bushing

Last updated March 11, 2022

A drill bushing, also known as a jig bushing,^[1] is a tool used in metalworking jigs to guide cutting tools, most commonly drill bits. Other tools that are commonly used in a drill bushing include counterbores, countersinks, and reamers. They are designed to guide, position, and support the cutting tool.^[2]

Types

Drill bushings can generally be classified as: press fit bushings or renewable bushings. Other classification methods include by head type, by use, and by liner type (or lack thereof).^[2]

Press-fit bushings

Press fit are available in two types with liners or without (wearing bushings). Liner bushings, sometimes called master bushings, are permanently installed into the jig and accept liners that can easily be replaced. Press-fit wearing bushings are used in short run applications or in applications where the tolerance on a hole location is so tight that it cannot facilitate the use of a liner bushing.^[3]

Renewable bushings

Renewable bushings are installed in liner bushings. This type of bushing is used in large production runs where a bushing will wear out over time or when multiple renewable bushings are used in one liner to provide various sized holes. There are two types of renewable bushings: fixed and slip.^[3]

Fixed renewable bushings are used in applications where the liner is meant to be used until it wears out. Slip renewable bushings are designed to be interchangeable with a given sized liner so that two different sized slip renewable bushings can be used in one liner bushing. This facilitates the ability to do multiple machining operations that require different inner diameter (ID) bushings, such as drilling and reaming. They usually have knurled heads so they can be easily removed.^[3]

Renewable bushings must be secured in their liner bushing, otherwise the tool can cause it to spin, which rapidly wears out the liner, or chips can force the bushing out of the liner. There are many different types of locking systems for renewable bushings. One system is a dog, which is a collar that is pressed over the head of the bushing and has a long tail. The tail may be bent at the end so it can lock around the edge of the jig plate or it may be left straight if it can butt up against another object. Another option to keep the renewable bushing from rotating is to pin it, either by putting a pin in the renewable bushing and a hole in the liner or vice versa. A more complicated version uses a hole in the bushing collar and a pin with a head; the head on the pin holds the edge of the collar down, but for removal the bushing can be rotated so that the hole lines up with the pin.^[5]

Specification

Customary bushings are specified using the following specification layout:^[3]

ID-Type-OD-Length

Where the ID is specified as a decimal, drill letter size, drill number size, or fraction; the OD is an integer that relates to a multiple of a 1⁄64th of an inch (0.40 mm); the length is an integer that relates to a multiple of a 1⁄16th of an inch. The lengths of press-fit bushings are standardized to typical jig plate thicknesses: 5⁄16, 3⁄8, 1⁄2, 3⁄4, 1 , 1+3⁄8, and 1+3⁄4 inch (7.94 mm, 9.53 mm, 12.7 mm, 19.05 mm, 25.4 mm, 34.93 mm and 44.45 mm). The letter "U" is used after the OD number to designate that extra stock should be left on the OD for grinding to size. The type is a letter referring to the following:^[3]

S - Slip renewable
F - Fixed renewable
L - Headless liner
HL - Head liner
P - Headless press-fit
H - Head press-fit

The following two tables give the tolerances for the ID and OD.

ID tolerances^[5]
Nominal ID [in]	[mm]	_	Maximum [in]	[mm]	Minimum [in]	[mm]
0–0.25 in	0.00–6.35 mm	including	0.0004 in	0.01016 mm	0.0001 in	0.00254 mm
0.25–0.75 in	6.35–19.05 mm	incl.	0.0005 in	0.0127 mm	0.0001 in	0.00254 mm
0.75–1.5 in	19.05–38.10 mm	incl.	0.0006 in	0.01524 mm	0.0002 in	0.00508 mm
1.5 in	38.1 mm	Greater than	0.0007 in	0.01778 mm	0.0003 in	0.00762 mm

OD grinding tolerances^[5]
Nominal OD [in]	[mm]	_	Maximum [in]	[mm]	Minimum [in]	[mm]
5⁄32–1⁄4 in	3.97–6.35 mm	_	0.005 in	0.127 mm	0.010 in	0.254 mm
5⁄16–13⁄64 in	7.94–5.16 mm	_	0.010 in	0.254 mm	0.015 in	0.381 mm
1⁄2 in	12.7 mm	Greater than	0.015 in	0.381 mm	0.020 in	0.508 mm

Custom bushings

A common problem encountered is when two or more holes are too close for independent standard bushings. In this case one large renewable bushing can be made with two (or more) holes in the proper location (the first example in the image). Another possibility is to make a custom bushing with an eccentric hole and then notches on the outside of the head are used to locate the proper position of the bushing for each location (the middle example in the image). Another common need for a custom bushing is when the hole needed is perpendicular jig plate; in this case a bracket bushing is used. It is a hardened piece of right angle steel that screws to the jig plate and is located with dowel pins.^[6]

Design

In general, a drill bushing's length should be at least 2 times the nominal ID.^[5]

Related Research Articles

A flange is a protruded ridge, lip or rim, either external or internal, that serves to increase strength ; for easy attachment/transfer of contact force with another object ; or for stabilizing and guiding the movements of a machine or its parts. The term "flange" is also used for a kind of tool used to form flanges.

Taps and dies are tools used to create screw threads, which is called threading. Many are cutting tools; others are forming tools. A tap is used to cut or form the female portion of the mating pair. A die is used to cut or form the male portion of the mating pair. The process of cutting or forming threads using a tap is called tapping, whereas the process using a die is called threading.

Drills are cutting tools used to remove material to create holes, almost always of circular cross-section. Drills come in many sizes and shapes and can create different kinds of holes in many different materials. In order to create holes drill bits are usually attached to a drill, which powers them to cut through the workpiece, typically by rotation. The drill will grasp the upper end of a bit called the shank in the chuck.

Roller chain or bush roller chain is the type of chain drive most commonly used for transmission of mechanical power on many kinds of domestic, industrial and agricultural machinery, including conveyors, wire- and tube-drawing machines, printing presses, cars, motorcycles, and bicycles. It consists of a series of short cylindrical rollers held together by side links. It is driven by a toothed wheel called a sprocket. It is a simple, reliable, and efficient means of power transmission.

A hole punch, also known as hole puncher, or paper puncher, is an office tool that is used to create holes in sheets of paper, often for the purpose of collecting the sheets in a binder or folder. A hole punch can also refer to similar tools for other materials, such as leather, cloth, or plastic or metal sheets.

Drilling is a cutting process that uses a drill bit to cut a hole of circular cross-section in solid materials. The drill bit is usually a rotary cutting tool, often multi-point. The bit is pressed against the work-piece and rotated at rates from hundreds to thousands of revolutions per minute. This forces the cutting edge against the work-piece, cutting off chips (swarf) from the hole as it is drilled.

A reamer is a type of rotary cutting tool used in metalworking. Precision reamers are designed to enlarge the size of a previously formed hole by a small amount but with a high degree of accuracy to leave smooth sides. There are also non-precision reamers which are used for more basic enlargement of holes or for removing burrs. The process of enlarging the hole is called reaming. There are many different types of reamer and they may be designed for use as a hand tool or in a machine tool, such as a milling machine or drill press.

A grinding machine, often shortened to grinder, is one of power tools or machine tools used for grinding. It is a type of machining using an abrasive wheel as the cutting tool. Each grain of abrasive on the wheel's surface cuts a small chip from the workpiece via shear deformation.

A socket wrench is a type of spanner, that uses a closed socket format, rather than a typical open wrench/spanner to turn a fastener, typically in the form of a nut or bolt.

A collet is a subtype of chuck that forms a collar around an object to be held and exerts a strong clamping force on the object when it is tightened, usually by means of a tapered outer collar. It may be used to hold a workpiece or a tool.

A chuck is a specialized type of clamp used to hold an object with radial symmetry, especially a cylinder. In a drill, a mill and a transmission, a chuck holds the rotating tool; in a lathe, it holds the rotating workpiece.

A machine taper is a system for securing cutting tools or toolholders in the spindle of a machine tool or power tool. A male member of conical form fits into the female socket, which has a matching taper of equal angle.

Safety wire or locking-wire is a type of positive locking device that prevents fasteners from falling out due to vibration and other forces. The presence of safety wiring may also serve to indicate that the fasteners have been properly tightened.

The shank is the end of a drill bit grasped by the chuck of a drill. The cutting edges of the drill bit contact the workpiece, and are connected via the shaft with the shank, which fits into the chuck. In many cases a general-purpose arrangement is used, such as a bit with cylindrical shaft and shank in a three-jaw chuck which grips a cylindrical shank tightly. Different shank and chuck combination can deliver improved performance, such as allowing higher torque, greater centering accuracy, or moving the bit independently of the chuck, with a hammer action.

In machining, boring is the process of enlarging a hole that has already been drilled by means of a single-point cutting tool, such as in boring a gun barrel or an engine cylinder. Boring is used to achieve greater accuracy of the diameter of a hole, and can be used to cut a tapered hole. Boring can be viewed as the internal-diameter counterpart to turning, which cuts external diameters.

A fixture is a work-holding or support device used in the manufacturing industry. Fixtures are used to securely locate and support the work, ensuring that all parts produced using the fixture will maintain conformity and interchangeability. Using a fixture improves the economy of production by allowing smooth operation and quick transition from part to part, reducing the requirement for skilled labor by simplifying how workpieces are mounted, and increasing conformity across a production run.

A jig is a type of custom-made tool used to control the location and/or motion of parts or other tools.

In mechanical engineering, a key is a machine element used to connect a rotating machine element to a shaft. The key prevents relative rotation between the two parts and may enable torque transmission. For a key to function, the shaft and rotating machine element must have a keyway and a keyseat, which is a slot and pocket in which the key fits. The whole system is called a keyed joint. A keyed joint may allow relative axial movement between the parts.

Screw Type of fastener characterized by a thread wrapped around a cylinder core

A screw and a bolt are similar types of fastener typically made of metal and characterized by a helical ridge, called a male thread. Screws and bolts are used to fasten materials by the engagement of the screw thread with a similar female thread in a matching part.

Injection mold construction is the process of creating molds that are used to perform injection molding operations using an injection molding machine. These are generally used to produce plastic parts using a core and a cavity.

References

↑ Colvin & Haas 1922 , p. 44.
1 2 3 Henriksen 1973 , p. 154.
1 2 3 4 5 6 Henriksen 1973 , p. 155.
↑ http://catalog.asme.org/Codes/PrintBook/B94331_1998_Jig_Bushings.cfm%5B%5D
1 2 3 4 Henriksen 1973 , p. 156.
↑ Colvin & Haas 1922 , pp. 45, 47.

Bibliography

Colvin, Fred Herbert; Haas, Lucian Levant (1922), Jigs and fixtures (2nd ed.), McGraw-Hill, p. 44.
Henriksen, Erik Karl (1973), Jig and fixture design manual, Industrial Press Inc., ISBN 978-0-8311-1098-7.

This page is based on this Wikipedia article
Text is available under the CC BY-SA 4.0 license; additional terms may apply.
Images, videos and audio are available under their respective licenses.

[1] Colvin & Haas 1922 , p. 44.

[henriksen154-2] 1 2 3 Henriksen 1973 , p. 154.

[henriksen155-3] 1 2 3 4 5 6 Henriksen 1973 , p. 155.

[4] ttp://catalog.asme.org/Codes/PrintBook/B94331_1998_Jig_Bushings.cfm%5B%5D

[henriksen156-5] 1 2 3 4 Henriksen 1973 , p. 156.

[6] Colvin & Haas 1922 , pp. 45, 47.

[1]

[2]

[3]

[4]

[5]

[6]