Feedback carburetor

Last updated

A feedback carburetor (also known as electronic or computer controlled carburetor) is a specific type of carburetor made mostly during the 1980s to improve emissions on certain vehicles in the US.

Contents

History

Before the 1970s, most vehicles didn't have many emissions systems on them, but as time went on, smog pumps, charcoal canisters, and thermal reactors were added to meet new regulations. [1] As vehicle emissions standards became more stringent due to the Clean Air Act and CAFE standards, vehicle engineers had to come up with different ways to meet this problem. Initially decreasing the engine compression and installing EGR systems and two way catalytic converters were able to solve this problem but later this became more difficult. In the 1980s, many vehicle manufacturers were required to use three-way catalytic converters and oxygen sensors to determine the air fuel ratio (AFR) of the vehicle to determine if the car is running correctly. [2] [3] [4]

This was paired with either an early version of fuel injection (typically through a Bosch Jetronic system for European vehicles) [5] or through a feedback carburetor, which had an increasing number of solenoids and settings to make sure the vehicle would emit less and less harmful emissions.

First results occurred in the mid to late 1970s, where Chrysler was first out with their new "Lean Burn" system in 1976 for its larger 400-cu in V8s, that would change engine timing and AFR so that it would run as lean as 18.0:1 AFR, which is much leaner than stoichiometric 14.7:1. [1]

Other brands would soon follow and would design different ways to tackle the same problem and would increase in complexity until they were replaced with electronic fuel injection (EFI) in the mid to late 1980s and early 1990s. Throttle Body Injection (TBI) was common to see as a cheap and simple way to swap to fuel injection in the 1980s from a carbureted engine design, and many early EFI cars used it until a newer engine could be designed for Multi Point Fuel Injection (MPFI).

Some of the last cars with carburetors in the US include the 1994 Isuzu Pickup, 1991 Jeep Grand Wagoneer, and the 1991 Ford Crown Victoria P72. [6]

Features and Operation

The basic operation of a feedback carburetor:

Examples

See also

Related Research Articles

<span class="mw-page-title-main">Carburetor</span> Component of internal combustion engines which mixes air and fuel in a controlled ratio

A carburetor is a device used by a gasoline internal combustion engine to control and mix air and fuel entering the engine. The primary method of adding fuel to the intake air is through the Venturi tube in the main metering circuit, though various other components are also used to provide extra fuel or air in specific circumstances.

<span class="mw-page-title-main">Catalytic converter</span> Exhaust emission control device

A catalytic converter is an exhaust emission control device which converts toxic gases and pollutants in exhaust gas from an internal combustion engine into less-toxic pollutants by catalyzing a redox reaction. Catalytic converters are usually used with internal combustion engines fueled by gasoline or diesel, including lean-burn engines, and sometimes on kerosene heaters and stoves.

<span class="mw-page-title-main">CVCC</span> Reduced-emissions engine by Honda

CVCC, or Compound Vortex Controlled Combustion, is an internal combustion engine technology developed and trademarked by the Honda Motor Company.

<span class="mw-page-title-main">Ford CVH engine</span> Reciprocating internal combustion engine

The Ford CVH engine is a straight-four automobile engine produced by the Ford Motor Company. The engine's name is an acronym for either Compound Valve-angle Hemispherical or Canted Valve Hemispherical, where "Hemispherical" describes the shape of the combustion chamber. The CVH was introduced in 1980 in the third generation European Escort and in 1981 in the first generation North American Escort.

Vehicle emissions control is the study of reducing the emissions produced by motor vehicles, especially internal combustion engines. The primary emissions studied include hydrocarbons, volatile organic compounds, carbon monoxide, carbon dioxide, nitrogen oxides, particulate matter, and sulfur oxides. Starting in the 1950s and 1960s, various regulatory agencies were formed with a primary focus on studying the vehicle emissions and their effects on human health and the environment. As the worlds understanding of vehicle emissions improved, so did the devices used to mitigate their impacts. The regulatory requirements of the Clean Air Act, which was amended many times, greatly restricted acceptable vehicle emissions. With the restrictions, vehicles started being designed more efficiently by utilizing various emission control systems and devices which became more common in vehicles over time.

<span class="mw-page-title-main">Ford Pinto engine</span> Reciprocating internal combustion engine

The Ford Pinto engine was the unofficial name for a four-cylinder internal combustion engine built by Ford Europe. In Ford sales literature, it was referred to as the EAO or OHC engine and because it was designed to the metric system, it was sometimes called the "metric engine". The internal Ford codename for the unit was the T88-series engine. European Ford service literature refers to it as the Taunus In-Line engine. In North America it was known as the Lima In-Line (LL), or simply the Lima engine due to its being manufactured at Lima Engine in Lima, Ohio.

An oxygen sensor (or lambda sensor, where lambda refers to air–fuel equivalence ratio, usually denoted by λ) or probe or sond, is an electronic device that measures the proportion of oxygen (O2) in the gas or liquid being analyzed.

Lean-burn refers to the burning of fuel with an excess of air in an internal combustion engine. In lean-burn engines the air–fuel ratio may be as lean as 65:1. The air / fuel ratio needed to stoichiometrically combust gasoline, by contrast, is 14.64:1. The excess of air in a lean-burn engine emits far less hydrocarbons. High air–fuel ratios can also be used to reduce losses caused by other engine power management systems such as throttling losses.

The Computerized Engine Control or Computerized Emission Control (CEC) system is an engine management system designed and used by American Motors Corporation (AMC) and Jeep on 4- and 6-cylinder engines of its own manufacture from 1980 to 1990. It is one of the three major components for proper engine operation: the computer, electrically controlled carburetor, and the oxygen sensor in the exhaust system.

<span class="mw-page-title-main">Back-fire</span> Explosion in the exhaust of an engine

A backfire or afterburn is combustion or an explosion produced by a running internal combustion engine that occurs in the exhaust system, rather than inside the combustion chamber. It is also sometimes referred to as an afterfire, especially in cases where the word backfire is used to mean a fuel burn that occurs while an intake valve is open, causing the fire to move backward through the system and out through the intake instead of the exhaust. When the flame moves backward it may also be called a "pop-back". A backfire can be caused either by ignition that happens with an exhaust valve open or unburnt fuel making its way into the hot exhaust system. A visible flame may momentarily shoot out of the exhaust pipe. A backfire is often a sign that the engine is improperly tuned.

<span class="mw-page-title-main">Autogas</span> Liquefied petroleum gas when it is used as a fuel in internal combustion engines

Autogas or LPG is liquefied petroleum gas (LPG) used as a fuel in internal combustion engines in vehicles as well as in stationary applications such as generators. It is a mixture of propane and butane.

<span class="mw-page-title-main">Douvrin engine</span> Reciprocating internal combustion engine

The Douvrin family is an all-aluminum inline-four automobile engine designed in the early 1970s and produced from 1977 to 1996 by Compagnie Française de Mécanique, a joint-venture between PSA and Renault located in the town of Douvrin in northern France. This engine is designed by the engineer Jean-Jacques His. It was produced in the same factory as the PRV V6, which also is sometimes known outside France as the "Douvrin" V6. The Douvrin engine is also referred to as the ZDJ/ZEJ engine by Peugeot, and as the J-type engine by Renault.

<span class="mw-page-title-main">Detroit Diesel V8 engine</span> Reciprocating internal combustion engine

The General Motors–Detroit Diesel V8 engine is a series of diesel V8 engines first introduced by General Motors for their C/K pickup trucks in 1982. Developed in collaboration with GM subsidiary Detroit Diesel, the engine family was produced by GM through 2002, when it was replaced by the new Duramax line. AM General's subsidiary General Engine Products (GEP) still produces a military variant of this engine for the HMMWV.

Renix was a joint venture by Renault and Bendix that designed and manufactured automobile electronic ignitions, fuel injection systems, electronic automatic transmission controls, and various engine sensors. Major applications included various Renault and Volvo vehicles. The name became synonymous in the U.S. with the computer and fuel injection system used on the AMC/Jeep 2.5 L I4 and 4.0 L I6 engines.

<span class="mw-page-title-main">Chevrolet Camaro (second generation)</span> Motor vehicle

The second-generation Chevrolet Camaro is an American pony car produced by Chevrolet from 1970 through the 1981 model years. It was introduced in the spring of 1970. Build information for model 123-12487 was released to the assembly plants in February of that same year. It was longer, lower, and wider than the first generation Camaro. A convertible was no longer available. GM engineers have said the second generation is much more of "a driver's car" than its predecessor. The high-performance Z/28 option remained available through 1975, redesignated as the Z28 in 1972.

The Ford EEC or Electronic Engine Control is a series of ECU that was designed and built by Ford Motor Company. The first system, EEC I, used processors and components developed by Toshiba in 1973. It began production in 1974, and went into mass production in 1975. It subsequently went through several model iterations.

<span class="mw-page-title-main">Motorcraft 2150 carburetor</span>

The Motorcraft 2150 is a Ford 2-barrel carburetor manufactured from 1973 through 1983, based heavily on its predecessor, the Autolite 2100 carburetor.

<span class="mw-page-title-main">Mitsubishi MCA</span>

Mitsubishi MCA stands for Mitsubishi Clean Air, a moniker used in Japan to identify vehicles built with emission control technology. The term was first introduced in Japan, with later introductions internationally. The technology first appeared in January 1973 on the Mitsubishi 4G32A gasoline-powered inline four cylinder engine installed in all Mitsubishi vehicles using the 4G32 engine, and the Saturn-6 6G34 six-cylinder gasoline-powered engine installed in the Mitsubishi Debonair. The technology was installed so that their vehicles would be in compliance with Japanese Government emission regulations passed in 1968.

The term Malaise era refers to a period in the U.S. automotive industry from roughly the early 1970s through the early to mid 1980s, characterized by malaise: poor products and a generalized industry unease — an era of profound adjustment as the U.S. automotive industry adapted to meet wholly new demands for more fuel-efficient, safe and environmentally responsible products.

References

  1. 1 2 Koch, Jeff (2024-03-26). "Chrysler's Lean-Burn System". Hemmings Motor News . Bennington, Vermont: American City Business Journals. OCLC   1245789004 . Retrieved 2024-11-16.
  2. ↑ US EPA, OAR (2016-06-27). "Timeline of Major Accomplishments in Transportation, Air Pollution, and Climate Change". www.epa.gov. Retrieved 2024-11-16.
  3. ↑ McDonald, W. R. (1978-02-01). Feedback Carburetor Control Electronic Design for Improved System Performance (Report). Warrendale, PA: SAE Technical Paper.
  4. ↑ "Advance Auto Parts - Down for Maintenance". shop.advanceautoparts.com. Retrieved 2024-11-16.
  5. ↑ admin (2018-09-20). "A Song of Air and Fuel: How Fuel Injection Got into Cars". Škoda Motorsport. Retrieved 2024-11-16.
  6. ↑ "Autotrader - page unavailable". www.autotrader.com. Retrieved 2024-11-16.
This page is based on this Wikipedia article
Text is available under the CC BY-SA 4.0 license; additional terms may apply.
Images, videos and audio are available under their respective licenses.