AMC computerized engine control

Last updated

The Computerized Engine Control or Computerized Emission Control (CEC) system is an engine management system designed and used by American Motors Corporation (AMC) and Jeep on 4- and 6-cylinder engines of its own manufacture from 1980 to 1990. [1] It is one of the three major components for proper engine operation: the computer, electrically controlled carburetor, and the oxygen sensor in the exhaust system. [2]

Contents

Starting with the 1986 model year, the AMC straight-4 engines used a throttle body injection (TBI) or single-point, fuel injection system with a new fully computerized engine control. [3] In addition to cycling the fuel injector (pulse-width time, on–off), the engine control computer also determined the ignition timing, idle speed, exhaust gas recirculation, etc. [4]

Operation

The AMC Computerized Engine Control is an electronic fuel feedback system is similar to those used by other automakers at the time by controlling the amount of gasoline to be atomized by the carburetor by precise electronic calculations. [5] The AMC CEC was unique in that almost all of its sensors and actuators were digital; instead of the usual analog throttle position, coolant temperature, intake temperature, and manifold pressure sensors, it used a set of fixed pressure- and temperature-controlled switches (as well as a wide-open throttle switch on the carburetor) to control fuel mixture and ignition timing. The only analog sensor in the system was the oxygen sensor. In other respects, it was a typical "feedback" carburetor system of the early-1980s, using a stepper motor to control fuel mixture and a two-stage "Sole-Vac" (which used a solenoid for one stage, and a vacuum motor for the other) to control idle speed. [6] The CEC also controlled ignition timing using information from the fuel-control section and an engine knock sensor on the intake manifold.

The CEC module itself (the most common version of which is the "AMC MCU Super-D") was manufactured for AMC by Ford Motor Company, and worked with a Duraspark ignition system. Although built by Ford, the CEC module is not related to the Ford EEC systems internally.

The AMC CEC went through at least four revisions. [5]

Maintenance

The system uses a maze of emissions vacuum hoses. [8] Because of the many vacuum-driven components and electrical connections in the system, CEC-equipped engines have developed a reputation of being hard to tune. [9] American Motors issued a Technical Service Bulletin to diagnose low or inconsistent engine idle speeds on 1980 through 1988 AMC Eagle automobile. [10]

The 49-state model of the CEC has no on-board diagnostic system, making it difficult to monitor the computer's operation without a breakout box, and the Carter BBD carburetor on most CEC-equipped models has problems with its idle circuit clogging, causing a rough idle and stalling. In places where emissions testing is not required, a modification is by bypassing the computer and disabling the BBD's Idle Servo, or replacing the BBD with a manually tuned carburetor. Several vendors (including Chrysler and Edelbrock) offer retrofit kits that replace the CEC and the carburetor with fuel injection. [8]

Related Research Articles

<span class="mw-page-title-main">Carburetor</span> Component of internal combustion engines which mixes air and fuel in a controlled ratio

A carburetor is a device used by an internal combustion engine to control and mix air and fuel entering the engine. The primary method of adding fuel to the intake air is through the Venturi tube in the main metering circuit, though various other components are also used to provide extra fuel or air in specific circumstances.

<span class="mw-page-title-main">Chrysler LA engine</span> Motor vehicle engine

The LA engines are a family of pushrod OHV small block 90° V-configured gasoline engines built by Chrysler Corporation. It was factory-installed in passenger vehicles, trucks and vans, commercial vehicles, marine and industrial applications from 1964 through 1991 (318) & 1992 (360). The combustion chambers are wedge-shaped, rather than the polyspherical combustion chambers in the predecessor A engine or the hemispherical combustion chambers in the Chrysler Hemi engine. LA engines have the same 4.46 in (113 mm) bore spacing as the A engines. LA engines were made at Chrysler's Mound Road Engine plant in Detroit, Michigan, as well as plants in Canada and Mexico. The "LA" stands for "Light A", as the 1956 - 1967 "A" engine it was closely based on and shares many parts with was nearly 50 pounds heavier. The "LA" and "A" production overlapped from 1964 - 1966 in the US and through 1967 in export vehicles when the "A" 318 engine was phased out. Willem Weertman, who later became Chief Engineer – Engine Design and Development, was in charge of the conversion. The basic design of the LA engine would go unchanged through the development of the "Magnum" upgrade (1992-1993) and into the 2000s with changes to enhance power and efficiency.

The Trionic 8 is an advanced engine management system in the Trionic series, created by Saab Automobile. It is used in both Saab 9-3 and Opel Vectra vehicles, and is available with 150, 175 and 210 horsepower (160 kW) engines. It will also be used for a flexifuel version starting production spring 2007. Saab Trionic T8 has been developed by Saab and is a very advanced engine management system. The Engine Control Module (ECM) is used principally to regulated the air mass, fuel and ignition timing.

Lean-burn refers to the burning of fuel with an excess of air in an internal combustion engine. In lean-burn engines the air:fuel ratio may be as lean as 65:1. The air / fuel ratio needed to stoichiometrically combust gasoline, by contrast, is 14.64:1. The excess of air in a lean-burn engine emits far less hydrocarbons. High air–fuel ratios can also be used to reduce losses caused by other engine power management systems such as throttling losses.

Manifold vacuum, or engine vacuum in an internal combustion engine is the difference in air pressure between the engine's intake manifold and Earth's atmosphere.

<span class="mw-page-title-main">MAP sensor</span>

The manifold absolute pressure sensor is one of the sensors used in an internal combustion engine's electronic control system.

<span class="mw-page-title-main">Engine control unit</span> Computer that adjusts electronics in an internal combustion propulsion system

An engine control unit (ECU), also commonly called an engine control module (ECM), is a type of electronic control unit that controls a series of actuators on an internal combustion engine to ensure optimal engine performance. It does this by reading values from a multitude of sensors within the engine bay, interpreting the data using multidimensional performance maps, and adjusting the engine actuators. Before ECUs, air–fuel mixture, ignition timing, and idle speed were mechanically set and dynamically controlled by mechanical and pneumatic means.

<span class="mw-page-title-main">Motronic</span>

Motronic is the trade name given to a range of digital engine control units developed by Robert Bosch GmbH which combined control of fuel injection and ignition in a single unit. By controlling both major systems in a single unit, many aspects of the engine's characteristics can be improved.

Secondary air injection is a vehicle emissions control strategy introduced in 1966, wherein fresh air is injected into the exhaust stream to allow for a fuller secondary combustion of exhaust gases.

A throttle is the mechanism by which fluid flow is managed by constriction or obstruction.

<span class="mw-page-title-main">Ignition timing</span>

In a spark ignition internal combustion engine, ignition timing is the timing, relative to the current piston position and crankshaft angle, of the release of a spark in the combustion chamber near the end of the compression stroke.

Renix was a joint venture by Renault and Bendix that designed and manufactured automobile electronic ignitions, fuel injection systems, electronic automatic transmission controls, and various engine sensors. Major applications included various Renault and Volvo vehicles. The name became synonymous in the U.S. with the computer and fuel injection system used on the AMC/Jeep 2.5 L I4 and 4.0 L I6 engines.

The following outline is provided as an overview of and topical guide to automobiles:

<span class="mw-page-title-main">Digifant engine management system</span>

The Digifant engine management system is an electronic engine control unit (ECU), which monitors and controls the fuel injection and ignition systems in petrol engines, designed by Volkswagen Group, in cooperation with Robert Bosch GmbH.

Trionic T5.5 is an engine management system in the Saab Trionic range. It controls ignition, fuel injection and turbo boost pressure. The system was introduced in the 1993 Saab 9000 2.3 Turbo with B234L and B234R engine.

Trionic is an engine management system developed by Saab Automobile. It consists of an engine control unit (ECU) that controls 3 engine aspects:

  1. Ignition timing
  2. Fuel injection
  3. Acts as a boost controller.
<span class="mw-page-title-main">Crankshaft position sensor</span> Import

A crank sensor (CKP) is an electronic device used in an internal combustion engine, both petrol and diesel, to monitor the position or rotational speed of the crankshaft. This information is used by engine management systems to control the fuel injection or the ignition system timing and other engine parameters. Before electronic crank sensors were available, the distributor would have to be manually adjusted to a timing mark on petrol engines.

The Ford EEC or Electronic Engine Control is a series of ECU that was designed and built by Ford Motor Company. The first system, EEC I, used processors and components developed by Toshiba in 1973. It began production in 1974, and went into mass production in 1975. It subsequently went through several model iterations.

<span class="mw-page-title-main">SECU-3</span>

SECU-3 is an internal combustion engine control unit. It is being developed as an open source project. Anyone can take part in the project, and can access all the information without any registrations.

References

  1. ↑ Fennema, Roger (1987). Automotive electrical and electronic systems, Volume 2. Harper & Row/Chek-Chart automotive series. HarperCollins. p. 308. ISBN   9780064540148 . Retrieved 28 May 2022– via Google Books.
  2. ↑ "The Three Major Players". gleebledorf.com. Retrieved 28 May 2022.
  3. ↑ "Detroit '86: Technical Highlights". Popular Mechanics. 162 (10): 35. October 1985. Retrieved 28 May 2022– via Google Books.
  4. ↑ Brady, Robert N. (1988). Automotive Computers and Digital Instrumentation. Prentice Hall. p. 283. ISBN   9780835902632.
  5. 1 2 "Depotting an 80's MCU from Ford...for AMC". Vintage Computer Federation Forums. 27 May 2019. Retrieved 28 May 2022.
  6. ↑ Ludel, Moses (22 April 2015). "How-to: YJ Wrangler 4.2L Six Two-Barrel 'BBD' Carburetor Rebuild!". 4WD Mechanix Magazine. Retrieved 28 May 2022.
  7. ↑ Statham, Steve (1999). Jeep Color History . MBI Publishers. p.  105. ISBN   9780760306369. AMC MCU Super-D.
  8. 1 2 Shipman, Mark. "EFI Options for the AMC 6-258 Engine". geekthing.com. Retrieved 28 May 2022.
  9. ↑ "AMC 258 I6". offroaders.com. Retrieved 28 May 2022.
  10. ↑ "AMC Technical Service Bulletin 12E460 – The idle speed may be too low or inconsistent on your 1980 – 1988 Eagle automobile". AMC Evolution. 4 February 2013. Archived from the original on 13 March 2014. Retrieved 28 May 2022.
This page is based on this Wikipedia article
Text is available under the CC BY-SA 4.0 license; additional terms may apply.
Images, videos and audio are available under their respective licenses.