Fitted For Wireless

Last updated
Austin K9 FFW, with 'house' body 1953 Austin K9 Radio Truck 4.0.jpg
Austin K9 FFW, with 'house' body

Fitted For Wireless (FFW) and Fitted For Radio (FFR) were British Army designators for vehicles equipped to carry radio equipment. Although many of these vehicles were dedicated 'radio vans' and had complex and expensive radio sets installed, the intention was also that general purpose vehicles could be issued in 'FFW' state with the low-cost but time-consuming cabling and equipment mounts already prepared. The actual sets themselves could be installed later, if a new radio vehicle was required owing to damage or breakdown.

Contents

'Wireless' is a period term for 'radio', particularly in British use. The two 'Fitted For ...' terms had distinct, but not obvious, uses in this particular context and are often confused.

Fitted For Wireless

World War II

FFW was the first term to be used and was applied to radio vehicles during World War II. Vehicle mounted wireless equipment early in the war was typically the Wireless Set No. 9 or No. 11, but after introduction in 1941, the No. 19 quickly became the standard set. This was a large, heavy, valve set, requiring a large power supply from heavy lead-acid batteries. A typical radio vehicle at this period would be a Bedford MW light truck of 8cwt or 15cwt capacity. [1] In its FFW configuration, this might be equipped with two No. 19 sets, one low-power operating alone and one high-power set equipped with an additional Amplifier RF No. 2. These sets were arranged on a fitted desk across the body of the truck, with four or eight 6 V lead-acid batteries beneath.

Wartime sets generally required a 6 V or 12 V supply, and batteries were charged by a small petrol-engined charging set (generator) of 300 W, often the 'Chorehorse' type. When in use, this generator was carried out of the vehicle on a carrying frame and placed on the ground outside. The vehicle's own engine and lighting batteries were separate. Some vehicles were fitted with additional radio charging dynamos driven from a gearbox PTO. Later in the war, 24 V vehicles began to appear, firstly US-supplied armoured vehicles, further complicating the wireless supply considerations. In the case of the 19 set, a composite power supply that allowed 12 V, two-wire 24 V and 3-wire (i.e. 0 - 12 - 24 V) systems was introduced. This power supply also contained a vibrator type HT section so that the receiver section of the set could be run more economically.

The largest of these World War II FFW vehicles were the 3-ton command vehicles on lorry chassis and the 6×6 AEC Armoured Command Vehicle. [2] These were built for the use of staff officers and carried map tables, several telephones and other equipment, with space for a senior officer and his staff in command. As well as No. 19 sets, they also carried the high power and long range transmitter Wireless Sender BC-610. [2] In this case they still carried the small 300 W charging set, but also a 3 kW generator set, usually an American-made Onan. [2] Most radio use would be made when established as a temporary headquarters with long-wire aerials rigged, in which case the generator set would be used dismounted. When on the move, or during the course of a battle, the low-power radios could still be used from batteries, with vertical whip aerials. The small charging set could be used to recharge these, with less effort and also less noise to give away a position.

Post-World War II

After World War II, FFW configurations were produced for the Jeep, [3] [4] Austin Champ [4] and Land Rover. [3] [4] In these smaller vehicles, it was necessary to construct racking to hold the sets and often to remove the rear seats. Owing to the small capacity of the Jeep and early Landrover charging systems, the 300W charging set was still required, although there was little space for it and was sometimes even mounted between the front seats. [5] The Austin Champ was provided with a high-output generator and shielded ignition system from the outset, and was also built in a dedicated FFW version from 1954. Single-set installations were produced for the Jeep during World War II [3] The introduction of the post-war and smaller C42 & C45 sets allowed a dual-set installation, even in these small 5cwt or ¼-ton vehicles. [4] Whip aerials for the VHF set(s) were installed on the front wings of these vehicles, together with their base-mounted Aerial Tuning Units to obtain maximum separation from any HF antenna. This practice became a distinctive feature of British Army vehicles in later years.

Larger vehicles, such as the Austin K9 1-ton [6] the Humber FV1600 series 1-ton or the 3-ton Bedford RL [7] had a less rigid installation. While these vehicles were available in FFW versions that were merely cargo vehicles fitted with additional generator capacity and outlets, dedicated communications vehicles had wood-framed 'house bodies' built on the chassis with a fitted desk inside and a standard Wireless Control Harness type B [8] The radio sets installed varied, according to the tactical role of the vehicle. Power was standardised at 24 volts (nominal) and in vehicles not equipped with power take-off facilities, still depended upon separate batteries and the use of a charging set.

Fitted For Radio

Land Rover 110 FFR, with wing mounted TRFA (Tuner Radio Frequency Antenna) boxes Land Rover 110 FFR (1986) owned by David Jimson.JPG
Land Rover 110 FFR, with wing mounted TRFA (Tuner Radio Frequency Antenna) boxes

In the 1950s, two factors changed the provision of vehicle radio within the British Army. The first of these was a change of philosophy for battlefield radio communication as a result of wartime experiences and the political and military situation in Europe after 1945 which was addressed by the "New Range" of sealed, primarily VHF/FM Combat Net Radio introduced from 1954. This later become known as the Larkspur series of equipment after the 1962 project to equip the whole army with the new radio system. [lower-roman 1] This modern design of equipment, although still using valves, was lightweight and where possible avoided the motor-generator/ rotary converter power supplies of earlier generation equipment such as the No. 19 set, in order to reduce the sets' power requirements.

The second factor was the development of the 'CT' (a contraction of CombaT) range of soft-skin combat vehicles, as a purpose-designed and more rugged alternative to the General Service vehicles based on modified commercial (CL) vehicles. [9] These CT vehicles, particularly the FV1801 Austin Champ ¼ ton and the FV1600 series Humber 1 ton, were powered by the new Rolls-Royce B range engines. Drawing on wartime experience, these engines were designed with built-in radio suppression, especially their ignition system, and they were also available with purpose-designed high-output generators, and were based on 24v systems in accordance with agreements reached with the US and Canadian armies in 1948. These 25A generators were initially thought sufficiently powerful to supply and charge the radio batteries directly, no longer needing the separate charging set. The generator had an internal two-speed automatic gearbox, which increased the charging rate when the engine was running at near-idling speed. However it soon became clear that this was insufficient to meet the demands of the new sets and higher output systems based on alternators were later introduced.

Fitted For Radio versions of the Champ [10] and Humber [11] were soon developed. This new term also represented a re-definition of the old FFW. FFR vehicles were those intended for immediate service with radios, and had the sets installed already. FFW now meant vehicles that were only partially equipped for radio use: the standard engine was suppressed against radio interference, [lower-roman 2] the radio mounting racks were either installed, or their mounting brackets were attached to the vehicle body, and aerial mounts had been installed. [10] The intention was that FFW was a low-cost addition at manufacture, but any FFW vehicle could now be rapidly upgraded to full FFR status in the field. Some FFR vehicles were supplied for specialised use (for example to the Royal Artillery) where non-standard radio equipment was to be fitted immediately, by unit workshops.

Two radio versions of the soft-skin Humber were developed: the FV1602 [11] with the same canvas-roofed general service truck body of the FV1601, with the addition of radio equipment. Secondly the FV1604 as a dedicated radio van, with a coachbuilt house body. [11]

When the supply of new Champs ceased in 1956, the production of FFR Land Rovers commenced, initially as 12Volt Rover Mk III and Mk V FFR's, but from 1958 (the start of the Series II Land Rover production - military designation Rover Mk VI) FFR switched to 24 Volt. The standard dynamo generator was initially replaced by a 40 Amp alternator with external rectifier stack mounted in front of the radiator for cooling giving the vehicle a distinctive appearance seen from the front of the vehicle, behind the radiator grille. Later vehicles were fitted with the AC90 alternator system manufactured by CAV which became a standardised system in light and medium British vehicles. FFR Land Rovers also had the front wing-mounted boxes for the 'Tuner Radio Frequency Antenna (TRFA)' antenna tuning units, with whip aerials mounted above them.

See also

Related Research Articles

Chieftain (tank) Main battle tank

The FV4201 Chieftain was the main battle tank of the United Kingdom during the 1960s-1990s.

Warrior tracked armoured vehicle Current British infantry fighting vehicle

The Warrior tracked vehicle family is a series of British armoured vehicles, originally developed to replace FV430 series armoured vehicles. The Warrior started life as the MCV-80, "Mechanised Combat Vehicle for the 1980s". One of the requirements of the new vehicle was a top speed able to keep up with the projected new MBT, the MBT-80 – later cancelled and replaced by what became the Challenger 1 – which the then-current FV432 armoured personnel carrier could not. The project was begun in 1972. GKN Defence won the production contract in 1984 and the Warrior was accepted for service with the British Army in November 1984. GKN Defence was purchased by BAE Systems, via Alvis plc.

FV432 Armoured personnel carrier

The FV432 is the armoured personnel carrier variant in the British Army's FV430 series of armoured fighting vehicles. Since its introduction in the 1960s, it has been the most common variant, being used for transporting infantry on the battlefield. At its peak in the 1980s, almost 2,500 vehicles were in use.

Humber Pig British lightly armoured truck

The Humber Pig is a lightly armoured truck used by the British Army from the 1950s until the early 1990s. The Pig saw service with the Royal Ulster Constabulary (RUC) chiefly as an armoured personnel carrier from late 1958 until early 1970. The Pig became particularly well known from its presence on the streets of Northern Ireland during the worst of the Troubles.

Humber Armoured Car Weapon

The Humber Armoured Car was one of the most widely produced British armoured cars of the Second World War. It supplemented the Humber Light Reconnaissance Car and remained in service until the end of the war.

Head-end power Electric power supply to trains by locomotives

In rail transport, head-end power (HEP), also known as electric train supply (ETS), is the electrical power distribution system on a passenger train. The power source, usually a locomotive at the front or 'head' of a train, provides the electricity used for heating, lighting, electrical and other 'hotel' needs. The maritime equivalent is hotel electric power. A successful attempt by the London, Brighton and South Coast Railway in October 1881 to light the passenger cars on the London to Brighton route heralded the beginning of using electricity to light trains in the world.

Alvis Stalwart Weapon

The Stalwart, formally classified by the British Army as Truck, High Mobility Load Carrier (HMLC), 5 Ton, 6 x 6, Alvis/Stalwart and informally known by servicemen as the Stolly, and by former RCT as the Stally, is a highly mobile amphibious military truck. Built by Alvis Cars between 1963 and 1971, these vehicles served with the British Army from 1964 until 1993.

Austin Gipsy Motor vehicle

The Austin Gipsy is an off-road vehicle produced by Austin from 1958 to 1968. It was designed as a lower-cost replacement for the Austin Champ, to compete directly with Rover's Land Rover. Like the Land Rover, it was aimed at both the civilian and military markets.

Land Rover 1/2 ton Lightweight

The Lightweight 1/2 ton was a British military vehicle supplied by Land Rover.

Austin Champ Motor vehicle

The Austin Champ was a military and civilian jeep-like vehicle made by the Austin Motor Company in the 1950s. The army version was officially known as "Truck, 1/4 ton, CT, 4×4, Cargo & FFW, Austin Mk.1" however the civilian name "Champ" was universally, if unofficially, applied to it. The majority of Champs produced went to the British Army.

London Underground battery-electric locomotives

London Underground battery-electric locomotives are battery locomotives used for hauling engineers' trains on the London Underground network where they can operate when the electric traction current is switched off. The first two locomotives were built in 1905 for the construction of the Great Northern, Piccadilly and Brompton Railway, and their success prompted the District Railway to buy two more in 1909, which were the only ones built to the loading gauge of the subsurface lines. Following this, a number of battery vehicles were built by converting redundant motor cars, with the batteries placed in the unused passenger compartment. One exception to this was made by the City and South London Railway, who used a trailer car to hold the batteries, and wired them to a separate locomotive.

Amateur radio station Amateur radio station

An amateur radio station is a radio station designed to provide radiocommunications in the amateur radio service for an amateur radio operator. Radio amateurs build and operate several types of amateur radio stations, including fixed ground stations, mobile stations, space stations, and temporary field stations. A slang term often used for an amateur station's location is the shack, named after the small enclosures added to the upperworks of naval ships to hold early radio equipment and batteries.

Land Rover Wolf Light utility vehicle

The Land Rover Wolf is a light military vehicle based on the Land Rover Defender introduced in 1994. The MoD designates the Wolf 90 as Truck Utility Light (TUL) HS and the Wolf 110 as Truck Utility Medium (TUM) HS. Where HS stands for High Specification. Land Rover calls it eXtra Duty (XD).

Clansman (military radio) Radio Communications System

Clansman is the name of a combat net radio system (CNR) used by the British Army from 1976 to 2010.

Commercial Utility Cargo Vehicle Motor vehicle

The Commercial Utility Cargo Vehicle (CUCV) is a vehicle program instituted to provide the United States military with light utility vehicles based on civilian trucks.

Land Rover series Motor vehicle

The Land Rover series I, II, and III, or simply the Land-Rover, are compact British off-road vehicles, produced by the Rover Company since 1948, and later by British Leyland. Though inspired by the World War II jeep, the Land Rover immediately distinguished itself from all other cars. From launch, it was the first mass-produced civilian four-wheel drive car with doors on it, and an available hard roof. Contrary to conventional car and truck chassis, it used a sturdier fully box-welded frame. Furthermore, due to post-war steel shortage, and aluminium surplus, Land Rovers received non-rusting aluminium alloy bodies, favouring their longevity. In 1992, Land Rover claimed that 70% of all the vehicles they had built were still in use.

MT-LBu Armored transporter

The MT-LBu is a Soviet multi-purpose fully amphibious armoured carrier which was developed under the factory index Ob'yekt 10 in the late 1960s, based on the MT-LB. It has a more powerful engine, a 40 cm higher hull and a longer chassis with 7 road wheels on each side.

Bedford QL Weapon

The Bedford QL was a series of trucks, manufactured by Bedford for use by the British Armed Forces in the Second World War.

Alternator (automotive) Devices in automobiles to charge the battery and power the electrical system

An alternator is a type of electric generator used in modern automobiles to charge the battery and to power the electrical system when its engine is running.

References

  1. ↑ The Larkspur program was launched in 1962, although some of the sets, the C42 & C45, had already entered service.
  2. ↑ This was already done for B range engines anyway.
  1. ↑ Meulstee, Louis (1998). Wireless for the Warrior. Vol. 2. G C Arnold. pp. WS.19 75–77. ISBN   1-898805-10-5.
  2. 1 2 3 Meulstee (1998), pp. 78—95
  3. 1 2 3 Meulstee (1998) , pp. 68–71
  4. 1 2 3 4 Meulstee (1998) , pp. 96–97
  5. ↑ Meulstee (1998), p. 65.
  6. ↑ Meulstee (1998) , pp. 99–102
  7. ↑ Meulstee (1998), p. 103.
  8. ↑ Louis Meulstee. "Larkspur Control Harness 'B'".
  9. ↑ Ware, Pat (1994). In National Service. Warehouse. pp. 6–9. ISBN   0952556308.
  10. 1 2 Ware (1994) , p. 65
  11. 1 2 3 Ware (1994) , p. 93
This page is based on this Wikipedia article
Text is available under the CC BY-SA 4.0 license; additional terms may apply.
Images, videos and audio are available under their respective licenses.