 | This article needs additional citations for verification .(April 2010) |
 HP-71B handheld BASIC computer | |
| Calculator | |
|---|---|
| Entry mode | BASIC |
The HP-71B was a hand-held computer or calculator programmable in BASIC, made by Hewlett-Packard from 1984 to 1989.
| | This article needs additional citations for verification .(April 2010) |
| HP-71B handheld BASIC computer | |
| Calculator | |
|---|---|
| Entry mode | BASIC |
The HP-71B was a hand-held computer or calculator programmable in BASIC, made by Hewlett-Packard from 1984 to 1989.
Smaller and less expensive than the preceding model HP-75, the 71B has a single-line 22-character liquid crystal display, 64K system ROM and 17.5K user memory. Priced at US$595 MSRP (US$1,700 in 2023), it operates on four AAA batteries. Four plug-in ports permits ROM-based programs or additional user memory to be added. Separate compartments could accommodate an optional magnetic card reader and an optional HP-IL interface (HP 82401A) that could be used to connect printers, storage and electronic test equipment.
The 71B was the first handheld to implement the IEEE 854-1987 radix-independent floating-point standard. Programming features included a real-time clock, programmable timers and subroutine calls with parameter passing and recursion. It was also HP's first calculator based on the Saturn processor, later versions of which are found in the popular HP-48 series calculators and most more recent HP calculator models.
Since the hand-pulled magnetic cards (HP-75 compatible) could only store two tracks of 650 bytes each, the card reader (installed under the logo plate above the numeric keyboard) was not a very popular option.[ citation needed ] Larger storage capacities could be accommodated through HP-IL peripherals such as the 82161A cassette drive or 9114A diskette drive that were also battery-powered and portable, if rather bulky compared to the 71B. Subsequently, memory expansion modules to fit the card reader compartment became available from third-party vendors.
Other third-party options included a bar code wand and application ROMs to plug into one of the four memory ports. A HP-71 configuration with bar code wand and a custom application was widely used for data collection in the British Department of Health and Social Security (DHSS).
Unlike HP-75 or HP-41, the 71B could also act as a device in a HP-IL loop controlled by another device, allowing several of them in the same loop, communicating with each other (or an HP-75 or HP-41) or sharing peripherals. Using an HP 82402 Dual HP-IL controller, it was even possible to connect one 71B to two HP-IL loops simultaneously, possibly as a controller in one and as a device in another.
The HP-71B could optionally be made compatible with the large volume of programs written for the HP-41 series of calculators via a plug-in ROM that emulated the HP-41 at about 5x the original speed.
Another notable "feature" of the 71B was that HP sold to the public a series of documents (IDS: Internal Design Specification) containing the nearly complete internal engineering details of the unit. A series of four IDSes were published about the software contained in the 71B's ROM; this included the complete source code (in assembly language) for the entire contents of ROM, and extensive additional design documentation of the ROM software. Other IDSes were released covering the 71B's hardware, the Forth/Assembler add-in ROM, and the add-in HP-IL controller.
| Authority control databases: National |
|---|
A motherboard is the main printed circuit board (PCB) in general-purpose computers and other expandable systems. It holds and allows communication between many of the crucial electronic components of a system, such as the central processing unit (CPU) and memory, and provides connectors for other peripherals. Unlike a backplane, a motherboard usually contains significant sub-systems, such as the central processor, the chipset's input/output and memory controllers, interface connectors, and other components integrated for general use.
The PDP–11 is a series of 16-bit minicomputers sold by Digital Equipment Corporation (DEC) from 1970 into the late 1990s, one of a set of products in the Programmed Data Processor (PDP) series. In total, around 600,000 PDP-11s of all models were sold, making it one of DEC's most successful product lines. The PDP-11 is considered by some experts to be the most popular minicomputer.
The IBM System/360 (S/360) is a family of mainframe computer systems that was announced by IBM on April 7, 1964, and delivered between 1965 and 1978. It was the first family of computers designed to cover both commercial and scientific applications and a complete range of applications from small to large. The design distinguished between architecture and implementation, allowing IBM to release a suite of compatible designs at different prices. All but the only partially compatible Model 44 and the most expensive systems use microcode to implement the instruction set, featuring 8-bit byte addressing and binary, decimal and hexadecimal floating-point calculations.
In computing, booting is the process of starting a computer as initiated via hardware such as a button on the computer or by a software command. After it is switched on, a computer's central processing unit (CPU) has no software in its main memory, so some process must load software into memory before it can be executed. This may be done by hardware or firmware in the CPU, or by a separate processor in the computer system.
IEEE 488, also known as HP-IB and generically as GPIB, is a short-range digital communications 8-bit parallel multi-master interface bus specification developed by Hewlett-Packard. It subsequently became the subject of several standards.
The TI-99/4 and TI-99/4A are home computers released by Texas Instruments in 1979 and 1981, respectively. The TI-99 series competed against home computers such as the Apple II, TRS-80, Atari 400/800, and VIC-20.
The HP-35 was Hewlett-Packard's first pocket calculator and the world's first scientific pocket calculator: a calculator with trigonometric and exponential functions. It was introduced in 1972.
The HP-65 is the first magnetic card-programmable handheld calculator. Introduced by Hewlett-Packard in 1974 at an MSRP of $795, it featured nine storage registers and room for 100 keystroke instructions. It also included a magnetic card reader/writer to save and load programs. Like all Hewlett-Packard calculators of the era and most since, the HP-65 used Reverse Polish Notation (RPN) and a four-level automatic operand stack.
The HP-IL, was a short-range interconnection bus or network introduced by Hewlett-Packard in the early 1980s. It enabled many devices such as printers, plotters, displays, storage devices, test equipment, etc. to be connected to programmable calculators such as the HP-41C, HP-71B and HP-75C/D, the Series 80 and HP-110 computers, as well as generic ISA bus based PCs.
The HP-41C series are programmable, expandable, continuous memory handheld RPN calculators made by Hewlett-Packard from 1979 to 1990. The original model, HP-41C, was the first of its kind to offer alphanumeric display capabilities. Later came the HP-41CV and HP-41CX, offering more memory and functionality.
An Option ROM for the PC platform is a piece of firmware that resides in ROM on an expansion card, which gets executed to initialize the device and (optionally) add support for the device to the BIOS. In its usual use, it is essentially a driver that interfaces between the BIOS API and hardware. Technically, an option ROM is firmware that is executed by the BIOS after POST and before the BIOS boot process, gaining complete control of the system and being generally unrestricted in what it can do. The BIOS relies on each option ROM to return control to the BIOS so that it can either call the next option ROM or commence the boot process. For this reason, it is possible for an option ROM to keep control and preempt the BIOS boot process. The BIOS generally scans for and initializes option ROMs in ascending address order at 2 KB address intervals within two different address ranges above address C0000h in the conventional (20-bit) memory address space; later systems may also scan additional address ranges in the 24-bit or 32-bit extended address space.
The HP 9800 is a family of what were initially called programmable calculators and later desktop computers that were made by Hewlett-Packard, replacing their first HP 9100 calculator. It is also named "98 line". The 9830 and its successors were true computers in the modern sense of the term, complete with a powerful BASIC language interpreter.
The TI-59 is an early programmable calculator, that was manufactured by Texas Instruments from 1977. It is the successor to the TI SR-52, quadrupling the number of "program steps" of storage, and adding "ROM Program Modules". Just like the SR-52, it has a magnetic card reader for external storage. One quarter of the memory is stored on each side of one card.
Programmable calculators are calculators that can automatically carry out a sequence of operations under control of a stored program. Most are Turing complete, and, as such, are theoretically general-purpose computers. However, their user interfaces and programming environments are specifically tailored to make performing small-scale numerical computations convenient, rather than general-purpose use.
The HP-75C and HP-75D were hand-held computers programmable in BASIC, made by Hewlett-Packard from 1982 to 1986.
This is a list of video game accessories that have been released for the Game Boy handheld console and its successors. Accessories add functionality that the console would otherwise not have.
A ROM cartridge, usually referred to in context simply as a cartridge, cart, or card, is a replaceable part designed to be connected to a consumer electronics device such as a home computer, video game console or, to a lesser extent, electronic musical instruments.
The HP 64000 Logic Development System, introduced 17 September 1979, is a tool for developing hardware and software for products based on commercial microprocessors from a variety of manufacturers. The systems assisted software development with assemblers and compilers for Pascal and C, provided hardware for in-circuit emulation of processors and memory, had debugging tools including logic analysis hardware, and a programmable read-only memory (PROM) chip programmer. A wide variety of optional cards and software were available tailored to particular microprocessors. When introduced the HP 64000 had two distinguishing characteristics. First, unlike most microprocessor development systems of the day, such as the Intel Intellec and Motorola EXORciser, it was not dedicated to a particular manufacturer's microprocessors, and second, it was designed such that up to six workstations could be connected via the HP-IB (IEEE-488) instrumentation bus to a common hard drive and printer to form a tightly integrated network.
A single-board microcontroller is a microcontroller built onto a single printed circuit board. This board provides all of the circuitry necessary for a useful control task: a microprocessor, I/O circuits, a clock generator, RAM, stored program memory and any necessary support ICs. The intention is that the board is immediately useful to an application developer, without requiring them to spend time and effort to develop controller hardware.
The HP-67 is a magnetic card-programmable handheld calculator, introduced by Hewlett-Packard in 1976 at an MSRP of $450. A desktop version with built-in thermal printer was sold as the HP-97 at a price of $750. Collectively, they are known as the HP-67/97.
