Lindal railway incident

Last updated

The hole at the Lindal sidings Lindal railway incident.jpg
The hole at the Lindal sidings

The Lindal railway incident happened on Thursday 22 September 1892 near Lindal-in-Furness, a village lying between the Cumbria towns of Ulverston and Dalton-in-Furness. A Furness Railway D1 locomotive, No.115, was shunting in sidings when it disappeared into the ground after a large, deep hole opened up beneath it. The D1 was never recovered and still lies buried beneath the railway, though the depth remains a source of speculation.

Contents

The story

East of Lindal station on the Barrow-Carnforth route, the two main lines and two goods lines ran along an embankment, with five sidings to the north. The 7am Barrow-Carnforth goods had stopped at the sidings behind Furness Railway locomotive No.115, a D1 class 0-6-0 built by the firm of Sharp Stewart between 1866 and 1885.

The ‘Sharpie’ (as the class were nicknamed) was busy shunting when the driver, Thomas Postlethwaite, saw cracks opening up in the ground right below. Knocking off steam, he jumped for his life, no sooner clear than the earth opened up to expose a sheer-sided hole 30 feet (9.1 m) across and similar in depth. The driver and his fireman stared in disbelief as their locomotive fell into it front first, the funnel and front part embedded, with only the tender remaining visible above the surface. The rails on which the engine had been standing were snapped off and went down with it, while the supporting baulks under the main lines were laid bare. The adjacent up passenger line was left hanging lopsidedly, its ballast having cascaded into the abyss.

Rescue attempts

Breakdown gangs from the locomotive and permanent way departments attended with a crane and tool vans. The tender was uncoupled and pulled clear, but the locomotive itself weighed 35 tons and getting it out would be a massive task. The hole had appeared just 45 minutes before a Barrow-Carnforth passenger was due, and rumours soon went round that a whole passenger train had been swallowed up and scores of people had been killed and injured. People flocked to look, but were kept from going too close by railway staff and police.

At 2:30 pm, the men took a break for refreshments and had not been clear long when the hole suddenly deepened to about 60 feet – the locomotive falling further still until the earth closed over it and eclipsed it from sight. Witnesses were awestruck to see the huge machine disappear so quickly from their sight, falling to an unknown depth and beyond recovery. The hole was even wider by then, with all eight tracks now twisted and bent, the ballast having fallen away, the sidings over which they had been able to take empty coaches was now unsafe to use.

Passengers on the 2.57 from Carnforth were forced to abandon the train and had to walk down the adjacent road to Lindal Station, where another train took them on to Barrow. Thirteen conveyances were chartered, including large brakes, buses and horse-drawn carts for their luggage.

Trainloads of ballast continued to arrive and though most thought the worst had been seen, the full extent of the subsidence could only be guessed at and no one yet knew when rails might start to be safely relaid. The uppermost level of the mine workings were 500 feet (150 m) down and No. 115 was considered to be lost forever. Others speculated that the locomotive was only 80 to 90 feet (24 to 27 m) down.

The hole eventually swallowed up around 300 wagon loads of ballast until a solid foundation was established. A Board of Trade inquiry was held under the auspices of Major-General C.S Hutchinson, veteran of numerous rail accidents including the Tay Bridge disaster of 1879. Lindal may not have been a tragedy, but was a fascinating case all the same. [1]

Disruption

Immediately after the first collapse, passengers were forced to alight from their trains and walk around the crater to the far side. The empty carriages were then taken slowly over the dubious tracks, passengers resettling themselves once their train was back on solid ground. Passengers were eager to see the hole and crowded round to get a good look while officials tried to hurry them along. Goods and mineral traffic were a major source of revenue, so keeping them running was vital. Coke for the ironworks at Barrow, Askam and Millom, normally came via Carnforth and Lindal, but with the whole line at a standstill and Carnforth yard blocked with stalled goods trains, coke trains had to be redirected via Penrith and Whitehaven, an extra 100 miles (160 km), the same route being used for livestock, perishables and goods traffic for the Belfast boats. Up Barrow to Carnforth workings were also disrupted and again redirected round the Penrith route.

Great efforts were made to get southbound trains away as quickly as possible, so as not to miss connections at Carnforth. Removing all the mails from Thursday evening's 7.45 pm and 9.00 pm from Barrow was a long-winded affair, but all the bags were transferred to the onward train, and so efficiently that it caught the Night Mail at Carnforth. Friday morning's mail was similarly dealt with, done and dusted within an hour.

Explanations

The embankment was encircled by a tell-tale pattern of dips and hollows indicating a history of subsidence. Shaky ground had already caused concerns, requiring trains to be ‘slowed’ before crossing a nearby bridge. Extra ballasting had been necessary and the two main lines, as well as having normal crossways sleepers also rested on longitudinal baulks of timber. A field below the embankment had a 70-by-30-foot (21.3 by 9.1 m) hollow nearly ten feet deep, and a nearby farmhouse had been abandoned because of subsidence. There were two levels of mine workings beneath the railway. The uppermost had not been used for some time, but miners in the lower level claimed they could hear trains above their heads and had already predicted a "big spill" someday.

Further subsidence

Subsidence was reported again in November 1893, the line sinking by six feet very close to the 1892 subsidence. Traffic was again brought to a halt and worked single line until the problem was solved. Lancashire MP Colonel Thomas Sandys wrote to the Board of Trade with his thoughts, suggesting the mines be filled in or a bridge be built to span the unsafe ground altogether. [2] The Board of Trade kept a watch on the Furness Railway for years afterwards, though directors were worried about adverse publicity. [3]

Alternative explanation

The explanation for the loss of No.115 given by a contemporary paper did not involve mining subsidence:

At the point where the subsidence took place there were large fissures in the rock, filled with sand. It is known that there is a subterranean stream below this, and it is supposed that owing to its action there has been a rush of sand, thus causing the subsidence [4]

In other words, the engine had not fallen into mine-workings but into a cavity caused by the collapse of an underlying sand-filled wash-hole or sink-hole of which the Furness area has many, mostly formed in the Ice Age. Where an underground water course washes out the sand it leaves a void. Heavy rainfall would accelerate removal of the fill, and heavy rainfall did precede the event: "[w]ith the heavy rains of late, there had been considerable flooding in the neighbourhood, and it is to this cause that the disaster is probably due." [5] At the time, the account given by The Engineer considered this possibility and identified how it might have been triggered by mining activity, but in the end thought it not the principal cause:

The railway at this point is undermined by the Parkside and Lindal Moor Mining Company, now leased by Messrs. Harrison, Ainslie, and Co., and for something like half a mile in length it is honeycombed by mining operations. For some time past evidence of the mine falling in, at any rate in its upper workings, has been seen, and on both sides of the railway embankment the ground has been gradually slipping for some time. The railway company, however, has been watching the action of this subsidence, and has placed a special watchman on the spot, with a view of detecting any change. Some time ago an adjoining farmhouse was let in, and the company found it necessary to prop up a railway bridge to prevent the line from collapsing. It is reported, however, that the workings of the Parkside mines have not been interfered with by the subsidence in the embankment, and that they exist intact under a stratification of rock which is as yet unshaken. The inference is that the vast volume of water which is pumped from the mines has caused percolation through the rock and left cavities in the upper strata which have caused a subsidence; but there is reason to believe that the subsidence which has now occurred is due mainly to the absolute fall of earth into old workings… [6]

Today

No.115 is officially regarded as "preserved",[ citation needed ] but recovery is a source of speculation. It may not lay as deep as long thought.[ citation needed ] Many[ who? ] believe that the locomotive is not far down, probably lying within the confines of the embankment.

The event provided the inspiration for the Arthur Conan Doyle story, "The Lost Special".

The incident has been the inspiration for the Rev. W. Awdry's railway series story "Down the Mine", and its Thomas and Friends adaptation. In the story and episode, Thomas the Tank Engine ignores a "danger" sign and falls into a small pit, later pulled out by Gordon, [7] though that story may equally have been inspired by a similar incident in April 1945 where an industrial locomotive, still with its driver on board, fell into a disused mine shaft. [8]

Related Research Articles

<span class="mw-page-title-main">Ravenglass and Eskdale Railway</span> Heritage railway in Cumbria, England

The Ravenglass and Eskdale Railway is a 15 in minimum gauge heritage railway in Cumbria, England. The 7-mile (11.3 km) line runs from Ravenglass to Dalegarth Station near Boot in the valley of Eskdale, in the Lake District. At Ravenglass the line ends at Ravenglass railway station on the Cumbrian Coast Line.

<span class="mw-page-title-main">Furness Railway</span> English railway company

The Furness Railway (Furness) was a railway company operating in the Furness area of Lancashire in North West England.

<span class="mw-page-title-main">Axholme Joint Railway</span> Successor to the Goole and Marshland Railway and Axholme Light Railway

The Axholme Joint Railway was a committee created as a joint enterprise between the Lancashire and Yorkshire Railway (L&Y) and the North Eastern Railway (NER) and was established by the North Eastern Railway Act of 31 July 1902. It took over the Goole and Marshland Railway, running from Marshland Junction near Goole to Reedness Junction and Fockerby, and the Isle of Axholme Light Railway, running from Reedness Junction to Haxey Junction. Construction of the Goole and Marshland Railway had begun in 1898, and by the time of the takeover in early 1903, was virtually complete. The Isle of Axholme Light Railway was started in 1899, but only the section from Reedness Junction to Crowle was complete at the takeover. The northern section opened on 10 August 1903, and the line from Crowle to Haxey Junction opened for passengers on 2 January 1905.

<span class="mw-page-title-main">Cumbrian Coast line</span> Rail route in North West England

The Cumbrian Coast line is a rail route in North West England, running from Carlisle to Barrow-in-Furness via Workington and Whitehaven. The line forms part of Network Rail route NW 4033, which continues via Ulverston and Grange-over-Sands to Carnforth, where it connects with the West Coast Main Line.

<span class="mw-page-title-main">Furness line</span>

The Furness line is a British railway between Barrow-in-Furness and Lancaster, joining the West Coast Main Line at Carnforth. A predominantly passenger line, it serves various towns along the Furness coast, including Barrow-in-Furness, Ulverston and Grange-over-Sands. It runs through Cumbria and Lancashire.

<span class="mw-page-title-main">Motive power depot</span> Rail yard for cleaning, repairing and maintaining locomotives

A motive power depot (MPD) or locomotive depot, or traction maintenance depot (TMD), is where locomotives are usually housed, repaired and maintained. They were originally known as "running sheds", "engine sheds" or just "sheds". Facilities are provided for refuelling and the replenishing of water, lubricating oil and grease and, for steam engines, the disposal of ash. There are often workshops for day-to-day repairs and maintenance, but locomotive building and major overhauls are usually carried out at locomotive works.

<span class="mw-page-title-main">Penistone rail accidents</span> List of rail accidents in Penistone South Yorkshire, England

Over the latter years of the 19th and early years of the 20th centuries, Penistone in Yorkshire gained a name as an accident black-spot on Britain's railway network; indeed, it could be said to hold the title of the worst accident black-spot in the country. The main line through the town was the Woodhead route of the Manchester, Sheffield and Lincolnshire Railway between Sheffield Victoria and Manchester, London Road. The line was heavily graded with a summit some 400 yards inside the eastern portal of the Woodhead tunnel.

The Wrexham and Minera Railway or Wrexham and Minera Branch was a railway line in North Wales between the city of Wrexham, the village of Brymbo where it served the Brymbo Steelworks, and the lead mines and limeworks at Minera. A further branch ran from Brymbo to Coed Talon, where it connected with lines to Mold. The system was constructed in several stages between 1844 and 1872, while the various lines making up the system closed in 1952, 1972 and 1982.

The Furness Railway Company owned many different types of locomotives, built by several locomotive building companies, including Sharp, Stewart and Company. Others were built by the Furness' constituent companies - the Whitehaven and Furness Junction Railway, among others.

<span class="mw-page-title-main">Coniston railway station (England)</span> Former station in Cumbria

Coniston railway station was the northern terminus of the Coniston branch line in the village of Coniston, Lancashire, England.

<span class="mw-page-title-main">East Kent Light Railway</span>

The East Kent Light Railway was part of the Colonel Stephens group of cheaply built rural light railways in England. Holman Fred Stephens was engineer from its inception, subsequently becoming director and manager. The line ran from Shepherdswell to Wingham Station with a branch from Eastry through Poison Cross to Richborough Port. Built primarily for colliery traffic within the Kent Coalfields, the line was built with many spurs and branches to serve the mines, with cancelled plans to construct extensions to several others. The success of Tilmanstone colliery allowed the main line of the railway to continue operation until 1986. A remainder of the line became the East Kent Railway, a heritage railway, in 1987.

<span class="mw-page-title-main">Barnoldswick railway station</span> Disused railway station in Lancashire, England

Barnoldswick was the only railway station on the Midland Railway's 1-mile-64-chain (2.9 km) long Barnoldswick Branch in the West Riding of Yorkshire in England ; it served the market town of Barnoldswick. The line left the Leeds and Bradford Extension Railway at Barnoldswick Junction 55 chains from Earby. The line through the junction was on a 20-chain radius after which it converged to a single track and ran in a straight but undulating line to Barnoldswick. The passenger train that ran back and forth between Barnoldswick and Earby was known locally as the Barlick Spud or Spudroaster. The real reason for the name is lost in time, but the two versions that were commonly recited are that the original branch locomotive was so small it looked like a portable potato roaster used by a local vendor or that the journey time was the same as that taken to roast a potato in the locomotive's firebox.

The Rosedale Railway was a 19.5-mile (31.4 km) goods-only railway line running from Battersby Junction via Ingleby Incline, across the heights of the North York Moors in North Yorkshire, England to reach iron ore deposits in the remote hills of the Rosedale valley. It opened to traffic as a narrow gauge railway to Ingleby Incline top in 1858, converted to standard gauge and opened to Rosedale West in 1861, and closed completely in 1929. Apart from Ingleby Incline, no major engineering works were constructed, and as such, particularly the east branch, the railway followed the contours of the surrounding hillside. The former trackbeds of the railway are in use by walkers and cyclists.

The Long Melford–Bury St Edmunds branch line was a railway between Long Melford on the Stour Valley Railway and Bury St Edmunds on the Ipswich to Ely Line. The line opened on 9 August 1865 and closed to passengers on 10 April 1961 and freight on 19 April 1965.

The Winsford and Over branch line was a railway line serving the town of Winsford in Cheshire. It was operated by the Cheshire Lines Committee (CLC) from 1870 until the railways were nationalised under the Transport Act 1947, which took effect on 1 January 1948. Thereafter the branch was operated by British Railways London Midland Region until the line's closure in 1967.

<span class="mw-page-title-main">Forest of Dean Railway</span> Disused railway in England

The Forest of Dean Railway was a railway company operating in Gloucestershire, England. It was formed in 1826 when the moribund Bullo Pill Railway and a connected private railway failed, and they were purchased by the new company. At this stage it was a horse-drawn plateway, charging a toll for private hauliers to use it with horse traction. The traffic was chiefly minerals from the Forest of Dean, in the Whimsey and Churchway areas, near modern-day Cinderford, for onward conveyance from Bullo Pill at first, and later by the Great Western Railway.

Chequerbent railway station was in Westhoughton to the south-west of Bolton, Greater Manchester, on a deviation of the original Bolton Great Moor St to Kenyon Junction line. The station replaced an earlier station on the original line of the railway that had been served by a stationary engine. It was open from 1885 until 1952 for passengers and 1965 for freight.

The Wetheral train accident occurred in England at about 4 p. m. on Saturday 3 December 1836 when a passenger train on the Newcastle and Carlisle Railway was wrongly diverted into a siding at Wetheral, a village close to Carlisle, Cumbria. The train derailed and crushed three people to death.

Carnforth MPD (Motive Power Depot) is a former London Midland and Scottish Railway railway depot located in the town of Carnforth, Lancashire, England.

Lindal railway station served Lindal-in-Furness in the Furness area of Lancashire, England .

References

  1. National Archives (Board of Trade report)
  2. National Archives (ministerial correspondence)
  3. National Archives (official Furness Railway letters)
  4. "Serious Subsidence on the Furness Railway – An Engine Sinks into a Pit". Cumberland Pacquet, and Ware's Whitehaven Advertiser. 29 September 1892. p. 8.
  5. "Subsidence on the Furness Railway – Engine over an Embankment". Lancaster Gazette. 24 September 1892. p. 8.
  6. "The Subsidence on the Furness Railway" (PDF). The Engineer. 30 September 1892. p. 281.
  7. "Pegnsean.net". Archived from the original on 14 December 2017. Retrieved 18 April 2013.
  8. Wigan World