Maximum acceptable toxicant concentration

Last updated

The maximum acceptable toxicant concentration (MATC) is a value that is calculated through aquatic toxicity tests to help set water quality regulations for the protection of aquatic life. Using the results of a partial life-cycle chronic toxicity test, the MATC is reported as the geometric mean between the No Observed Effect Concentration (NOEC) and the lowest observed effect concentration (LOEC). [1]

Contents

The MATC is used to set regulatory standards for priority pollutants [2] under the US federal Clean Water Act. Regulatory guidelines give two acceptable concentrations of pollutants to protect against effects: chronic or acute. Since the MATC should only be reported in chronic toxicity tests, there is a widely accepted method to convert the chronic MATC to a concentration that protects against acute effects. [1]

The MATC is calculated and reported from the results of a number of standard procedures designed by the United States Environmental Protection Agency (US EPA) and other organizations to maintain high accuracy and precision among all toxicity tests for regulatory purposes.

Calculation

Chronic toxicity tests

In a toxicity test, the NOEC and LOEC are derived as a comparison from the negative control, or the experimental group that does not contain the chemical in question. The NOEC is the highest concentration that does not cause a statistically different effect than the negative control through statistical hypothesis testing. Likewise, the LOEC is the lowest concentration tested that does cause a statistically different effect than the negative control. The MATC is the geometric mean between these two values, such that: MATC=√(NOEC)(LOEC)

The MATC is calculated to protect against chronic effects on overall function or health of an organism, not death. A partial life cycle test must be used. This type of toxicity test uses organisms in their most sensitive life stages, usually during times of early reproduction and growth, but not juveniles. [3] The MATC is the highest concentration that should not cause chronic effects, however, for regulatory purposes, a maximum concentration to protect against acute effects must exist as well.

Applying MATC to acutely toxic concentrations

The MATC can be applied to the results of an acute toxicity test to obtain a concentration that would protect against adverse effects during an acute exposure. An LC50, or the concentration at which 50% of the organisms die during an acute toxicity test is used to derive a value called the acute to chronic ratio (ACR).

The MATC can be used to calculate the ACR as follows:

The ACR is useful for estimating an MATC for species in which only acute toxicity data exists, or for setting regulatory guidelines for the protection of aquatic life through water quality criteria by the US EPA. [3]

Regulatory uses

United States

The US EPA is the governmental organization responsible for writing and enforcing environmental regulations passed by Congress. The Clean Water Act was passed in 1972.

Section 304(a)(1) of the Clean Water Act is the Water Quality Criteria (WQC) developed for the protection of aquatic life and human health. [4] The MATC and ACR are used in a sequence of calculations to obtain the Criterion Maximum Concentration and Criterion Continuous Concentration (CMC and CCC, respectively) for the chemicals being regulated. [5]

The CMC and CCC are two of the six parts of the aquatic life criterion under the WQC, and are the actual regulatory values for all priority pollutants tested. The CMC is the highest concentration of a chemical in water that aquatic organisms can be exposed to acutely without causing an adverse effect. Likewise, the CCC is the highest concentration of a chemical in water that aquatic organisms can be exposed to indefinitely without resulting in an adverse effect. Typically, the CMC is higher than the CCC. [5]

Canada

Environment Canada is the regulatory agency for environmental protection in Canada. Under the Canada Water Act of 1970, the Canadian Water Quality Guidelines (CWQG) for the Protection of Aquatic Life give regulatory guidelines of maximum concentrations of pollutants that are acceptable in freshwater and marine environments. [6]

The CWQG's long and short-term exposure concentrations are derived in a similar way as the methods used by the US EPA, and are the CMC or CCC equivalents. [7] When an MATC is reported with toxicity tests, it has sometimes been called a threshold-observed-effect-concentration (TOEC). The MATC and TOEC are both calculated as the geometric mean of the NOEC and LOEC, and are often used interchangeably. [7] [8]

Standard methods

Standard methods are designed and used widely to maximize precision and accuracy for all toxicity tests. Values derived from toxicity tests such as the MATC are reported to regulatory organizations like the US EPA and Environment Canada so more confident regulations can be designed.[ citation needed ]

Some common standard methods include those designed by the governmental organizations like Environment Canada, the US EPA, or the United States Food and Drug Administration (FDA). Others are designed by scientific organizations such as ASTM International, or the OECD.

Many of these methods use the same test organism or are designed for the same exposure time. Common test organisms include, but are not limited to, daphnia, fathead minnow, rainbow trout, and mussels. Acute toxicity tests are normally 24–96 hours, whereas chronic tests will typically run for a week or longer.

Advantages and limitations

Using the MATC to derive regulatory guidelines has been accompanied with some debate. Hypothesis testing, or statistical tests performed with data sets that only report a significant difference, are not considered the most statistically robust. There are no confidence intervals to show a measure of uncertainty in a NOEC and LOEC. In addition, the NOEC and LOEC can only be concentrations in the test, and nothing in between. [9] Because of these reasons, values that are derived through curve fitting methods, such as an LC50, or EC10 (the concentration that causes the measured effect in 10% of organisms) would be preferred if it was possible more often.

From a regulatory standpoint, there are advantages to using results from hypothesis tests. NOEC and LOEC’s were used more often in the past, and there are more test results reporting NOEC and LOEC’s than EC10’s. The time and effort required to perform all of the previous tests to derive a different value is not seen as a good use of resources. In addition, the use of NOEC and LOEC’s allows for reporting of one number to regulatory agencies. [8] Water Quality Criteria are reported as one number that the actual concentration must remain below. If the MATC were reported as a range of values to account for uncertainty, the regulatory guidelines would not be presented as a single value.

Related Research Articles

Toxicity Degree of harmfulness of substances

Toxicity is the degree to which a chemical substance or a particular mixture of substances can damage an organism. Toxicity can refer to the effect on a whole organism, such as an animal, bacterium, or plant, as well as the effect on a substructure of the organism, such as a cell (cytotoxicity) or an organ such as the liver (hepatotoxicity). By extension, the word may be metaphorically used to describe toxic effects on larger and more complex groups, such as the family unit or society at large. Sometimes the word is more or less synonymous with poisoning in everyday usage.

Chronic toxicity, the development of adverse effects as a result of long term exposure to a contaminant or other stressor, is an important aspect of aquatic toxicology. Adverse effects associated with chronic toxicity can be directly lethal but are more commonly sublethal, including changes in growth, reproduction, or behavior. Chronic toxicity is in contrast to acute toxicity, which occurs over a shorter period of time to higher concentrations. Various toxicity tests can be performed to assess the chronic toxicity of different contaminants, and usually last at least 10% of an organism's lifespan. Results of aquatic chronic toxicity tests can be used to determine water quality guidelines and regulations for protection of aquatic organisms.

Environmental chemistry Scientific study of the chemical and phenomena that occur in natural places

Environmental chemistry is the scientific study of the chemical and biochemical phenomena that occur in natural places. It should not be confused with green chemistry, which seeks to reduce potential pollution at its source. It can be defined as the study of the sources, reactions, transport, effects, and fates of chemical species in the air, soil, and water environments; and the effect of human activity and biological activity on these. Environmental chemistry is an interdisciplinary science that includes atmospheric, aquatic and soil chemistry, as well as heavily relying on analytical chemistry and being related to environmental and other areas of science.

Aquatic toxicology

Aquatic toxicology is the study of the effects of manufactured chemicals and other anthropogenic and natural materials and activities on aquatic organisms at various levels of organization, from subcellular through individual organisms to communities and ecosystems. Aquatic toxicology is a multidisciplinary field which integrates toxicology, aquatic ecology and aquatic chemistry.

Endrin Chemical compound

Endrin is an organochloride with the chemical formula C12H8Cl6O that was first produced in 1950 by Shell and Velsicol Chemical Corporation. It was primarily used as an insecticide, as well as a rodenticide and piscicide. It is a colourless, odorless solid, although commercial samples are often off-white. Endrin was manufactured as an emulsifiable solution known commercially as Endrex. The compound became infamous as a persistent organic pollutant and for this reason it is banned in many countries.

Wastewater quality indicators

Wastewater quality indicators are laboratory test methodologies to assess suitability of wastewater for disposal, treatment or reuse. The main parameters in sewage that are measured to assess the sewage strength or quality as well as treatment options include: solids, indicators of organic matter, nitrogen, phosphorus, indicators of fecal contamination. Tests selected vary with the intended use or discharge location. Tests can measure physical, chemical, and biological characteristics of the wastewater. Physical characteristics include temperature and solids. Chemical characteristics include pH value, dissolved oxygen concentrations, biochemical oxygen demand (BOD) and chemical oxygen demand (COD), nitrogen, phosphorus, chlorine. Biological characteristics are determined with bioassays and aquatic toxicology tests.

Environmental toxicology

Environmental toxicology is a multidisciplinary field of science concerned with the study of the harmful effects of various chemical, biological and physical agents on living organisms. Ecotoxicology is a subdiscipline of environmental toxicology concerned with studying the harmful effects of toxicants at the population and ecosystem levels.

A Discharge Monitoring Report (DMR) is a United States regulatory term for a periodic water pollution report prepared by industries, municipalities and other facilities discharging to surface waters. The facilities collect wastewater samples, conduct chemical and/or biological tests of the samples, and submit reports to a state agency or the United States Environmental Protection Agency (EPA). All point source dischargers to ”Waters of the U.S.” must obtain a National Pollution Discharge Elimination System (NPDES) permit from the appropriate agency, and many permittees are required to file DMRs.

Assimilative capacity is the ability for pollutants to be absorbed by an environment without detrimental effects to the environment or those who use of it. Natural absorption into an environment is achieved through dilution, dispersion and removal through chemical or biological processes. The term assimilative capacity has been used interchangeably with environmental capacity, receiving capacity and absorptive capacity. It is used as a measurement perimeter in hydrology, meteorology and pedology for a variety of environments examples consist of: lakes, rivers, oceans, cities and soils. Assimilative capacity is a subjective measurement that is quantified by governments and institutions such as Environmental Protection Agency (EPA) of environments into guidelines. Using assimilative capacity as a guideline can help the allocation of resources while reducing the impact on organisms in an environment. This concept is paired with carrying capacity in order to facilitate sustainable development of city regions. Assimilative capacity has been critiqued as to its effectiveness due to ambiguity in its definition that can confuses readers and false assumptions that a small amount of pollutants has no harmful effect on an environment.

In environmental toxicology, effects range low (ERL) and effects range median (ERM) are measures of toxicity in marine sediment. They are used by public agencies in the United States in formulating guidelines in assessing toxicity hazards, in particular from trace metals or organic contaminants.

The Biotic Ligand Model (BLM) is a tool used in aquatic toxicology that examines the bioavailability of metals in the aquatic environment and the affinity of these metals to accumulate on gill surfaces of organisms. BLM depends on the site-specific water quality including such parameters as pH, hardness, and dissolved organic carbon. In this model, lethal accumulation values are used to be predictive of lethal concentration values that are more universal for aquatic toxicology and the development of standards. Collection of water chemistry parameters for a given site, incorporation of the data into the BLM computer model and analysis of the output data is used to accomplish BLM analysis. Comparison of these values derived from the model, have repeatedly been found to be comparable to the results of lethal tissue concentrations from acute toxicity tests. The BLM was developed from the gill surface interaction model (GSIM) and the free ion activity model (FIAM). Both of these models also address how metals interact with organisms and aquatic environments. Currently, the United States Environmental Protection Agency (EPA) uses the BLM as a tool to outline Ambient Water Quality Criteria (AWQC) for surface water. Because BLM is so useful for investigation of metals in surface water, there are developmental plans to expand BLM for use in marine and estuarine environments.

Tissue residue is the concentration of a chemical or compound in an organism's tissue or in a portion of an organism's tissue. Tissue residue is used in aquatic toxicology to help determine the fate of chemicals in aquatic systems, bioaccumulation of a substance, or bioavailability of a substance, account for multiple routes of exposure, and address an organism's exposure to chemical mixtures. A tissue residue approach to toxicity testing is considered a more direct and less variable measure of chemical exposure and is less dependent on external environmental factors than measuring the concentration of a chemical in the exposure media.

An early life stage (ELS) test is a chronic toxicity test using sensitive early life stages like embryos or larvae to predict the effects of toxicants on organisms. ELS tests were developed to be quicker and more cost-efficient than full life-cycle tests, taking on average 1–5 months to complete compared to 6–12 months for a life-cycle test. They are commonly used in aquatic toxicology, particularly with fish. Growth and survival are the typically measured endpoints, for which a Maximum Acceptable Toxicant Concentration (MATC) can be estimated. ELS tests allow for the testing of fish species that otherwise could not be studied due to length of life, spawning requirements, or size. ELS tests are used as part of environmental risk assessments by regulatory agencies including the U.S. Environmental Protection Agency (EPA) and Environment Canada, as well as the Organisation for Economic Co-operation and Development (OECD).

Simultaneously extracted metals/Acid-volatile sulfide (SEM-AVS) is an approach used in the field of aquatic toxicology to assess the potential for metal ions found in sediment to cause toxic effects in organisms dwelling in the sediment. In this approach, the amounts of several heavy metals in a sediment sample are measured in a laboratory; at the same time, the amount of acid-volatile sulfide is determined. Based on the chemical interactions between heavy metals (SEM) and acid-volatile sulfide (AVS), the concentrations of these two components can be used to assess the potential for toxicity to sediment-dwelling organisms.

Equilibrium partitioning Sediment Benchmarks (ESBs) are a type of Sediment Quality Guideline (SQG) derived by the US Environmental Protection Agency (EPA) for the protection of benthic organisms. ESBs are based on the bioavailable concentration of contaminants in sediments rather than the dry-weight concentration. It has been demonstrated that sediment concentrations on a dry-weight basis often do not predict biological effects. Interstitial water concentrations, however, predict biological effects much better. This is true because the chemical present in the interstitial water is the uncomplexed/free phase of the chemical that is bioavailable and toxic to benthic organisms. Other phases of the chemical are bound to sediment particles like organic carbon (OC) or acid volatile sulfides (AVS) and are not bioavailable. Thus the interstitial water concentration is important to consider for effects to benthic organisms.

The predicted no-effect concentration (PNEC) is the concentration of a chemical which marks the limit at which below no adverse effects of exposure in an ecosystem are measured. PNEC values are intended to be conservative and predict the concentration at which a chemical will likely have no toxic effect. They are not intended to predict the upper limit of concentration of a chemical that has a toxic effect. PNEC values are often used in environmental risk assessment as a tool in ecotoxicology. A PNEC for a chemical can be calculated with acute toxicity or chronic toxicity single-species data, Species Sensitivity Distribution (SSD) multi-species data, field data or model ecosystems data. Depending on the type of data used, an assessment factor is used to account for the confidence of the toxicity data being extrapolated to an entire ecosystem.

In aquatic toxicology, the sediment quality triad (SQT) approach has been used as an assessment tool to evaluate the extent of sediment degradation resulting from contaminants released due to human activity present in aquatic environments. This evaluation focuses on three main components: 1.) sediment chemistry, 2.) sediment toxicity tests using aquatic organisms, and 3.) the field effects on the benthic organisms. Often used in risk assessment, the combination of three lines of evidence can lead to a comprehensive understanding of the possible effects to the aquatic community. Although the SQT approach does not provide a cause-and-effect relationship linking concentrations of individual chemicals to adverse biological effects, it does provide an assessment of sediment quality commonly used to explain sediment characteristics quantitatively. The information provided by each portion of the SQT is unique and complementary, and the combination of these portions is necessary because no single characteristic provides comprehensive information regarding a specific site

Toxicological databases are large compilations of data derived from aquatic and environmental toxicity studies. Data is aggregated from a large number of individual studies in which toxic effects upon aquatic and terrestrial organisms have been determined for different chemicals. These databases are then used by toxicologists, chemists, regulatory agencies and scientists to investigate and predict the likelihood that an organic or inorganic chemical will cause an adverse effect on exposed organisms.

The acute to chronic ratio (ACR) uses acute toxicity data to gauge the chronic toxicity (MATC) of a chemical of interest to an organism. The science behind determining a safe concentration to the environment is imperfect, statistically limited, and resource intensive. There is an unfilled demand for the rapid assessment of different chemical toxicity to many different organisms. The ACR is a proposed solution to this demand.

Toxic units (TU) are used in the field of toxicology to quantify the interactions of toxicants in binary mixtures of chemicals. A toxic unit for a given compound is based on the concentration at which there is a 50% effect for a certain biological endpoint. One toxic unit is equal to the EC50 for a given endpoint for a specific biological effect over a given amount of time. Toxic units allow for the comparison of the individual toxicities of a binary mixture to the combined toxicity. This allows researchers to categorize mixtures as additive, synergistic or antagonistic. Synergism and antagonism are defined by mixtures that are more or less toxic than predicted by the sum of their toxic units.

References

[1]

[2]

[3]

[4]

[5]

[6]

. [7]

. [8]

. [9]

  1. 1 2 3 Rand, Gary (1995). Fundamentals of Aquatic Toxicology. Boca Raton: CRC Press. pp. 943. ISBN   1-56032-090-7.
  2. 1 2 U.S. EPA. Priority Pollutants .
  3. 1 2 3 Rand, Gary (1995). Fundamentals of Aquatic Toxicology. Boca Raton: CRC Press. pp. 42-43. ISBN   1-56032-090-7.
  4. 1 2 U.S. E.P.A. Water Quality Criteria .
  5. 1 2 3 U.S. EPA. CMC and CCC .
  6. 1 2 Canadian Water Quality Guidelines. CCME Guidelines for the protection of aquatic life. "Archived copy". Archived from the original on 2007-08-23. Retrieved 2013-05-31.CS1 maint: archived copy as title (link).
  7. 1 2 3 Canadian Council of Minister of the Environment. A Protocol for the Derivation of Water Quality Guidelines for the Protection of Aquatic Life 2007 [ceqg-rcqe.ccme.ca/download/en/220/]
  8. 1 2 3 Environment Canada (2005). Guidance Document on Statistical Methods for Environmental Toxicity Tests. pp. 113. EPS 1/RM/46
  9. 1 2 Rand, Gary (1995). Fundamentals of Aquatic Toxicology. Boca Raton: CRC Press. pp. 86-87. ISBN   1-56032-090-7
This page is based on this Wikipedia article
Text is available under the CC BY-SA 4.0 license; additional terms may apply.
Images, videos and audio are available under their respective licenses.