Modular Engine Management System

Last updated
Modular Engine Management System
Rover MEMS 1.6 ECU.jpg
MEMS 1.6 units, one with its cover removed
Manufacturer Rover Group / Motorola
TypeElectronic automobile engine management
Release date1989

The Modular Engine Management System, or MEMS, is an electronic control system used on engines in passenger cars built by Rover Group in the 1990s. As its name implies, it was adaptable for a variety of engine management demands, including electronically controlled carburetion as well as single- and multi-point fuel injection (both with and without electronic ignition control). The abbreviations "SPi" and "MPi" refer to the single-point and multi-point injection configurations, respectively. [1]

Contents

In 1985, Rover Group made the decision to develop a new electronic engine management system in-house, and from its inception, the system was intended to be flexible enough for use with future engine designs. It was also intended to improve quality and reliability and to consume less power and occupy less underbonnet space than previous engine management systems. [2] The system first became available in 1989, when it was fitted to the Austin Montego 2.0L. Over the next seven years, the system appeared on cars across Rover's model lineup, including the Mk VI and Mk VII Mini and the MG F / MG TF. It was also paired with Rover engines used by other marques, such as the Lotus Elise and several Caterham models using the Rover K-series engine. [3]

Hardware

The ECU design was a joint venture between Rover and Motorola Automotive and Industrial Electronics Group (AIEG), who were responsible for the ECU manufacturing. The software run on the ECU was designed and written by Rover Group engineers. The "Modular" characteristic of the ECU was represented in the hardware design, which featured a common core with multiple optional add-on modules. In 1990, these modular features included the following: [2]

The processor in the ECU is an Intel 8096 running at 12 MHz and featuring 8KB of on-chip ROM for storage of code and data and 232 bytes of general-purpose RAM. The main connector is a 36-pin TE Connectivity 344108 ("Econoseal"), and its mating connector (used in the wiring harness) is a TE Connectivity 344111. On earlier versions of the system, a MAP sensor was internal to the ECU, requiring that an inlet manifold vacuum line be run to the ECU enclosure. In MEMS 1.6 and 1.9, this MAP sensor is the Motorola 5141550T02, [4] and the vacuum line feeding it passes through a vapor trap to prevent admission of fuel vapor into the ECU. [5]

An analogous system for engines with a carburettor was developed at the same time as MEMS. This system was known as "ERIC", which stands for "Electronically Regulated Ignition and Carburetion". [1] The development of the MEMS and ERIC systems became the first in-house units for ignition and fuel-control, areas which had previously been undertaken by Lucas Engine Management Systems, a division of Lucas Industries. While the development of MEMS and ERIC occurred at the same time, there was no commonality between the two systems - while MEMS used an Intel micro-controller, the ERIC system used the Motorola 68HC11 device; the development of MEMS used a PC based toolset, while that of ERIC used a Unix based toolset; the two teams working on MEMS and ERIC were totally independent.[ citation needed ]

Function

Like other electronic engine management systems, MEMS reads data from a number of sensors and computes an appropriate fueling rate and ignition advance/retard. The ECU samples engine speed, manifold absolute pressure, coolant temperature, intake air temperature, throttle position, and battery voltage. Base values for the fueling and ignition timing are each retrieved from a three-dimensional map, and certain sensor values are applied as correction factors, for example, to enrich fueling during wide-throttle acceleration or on cold startup. The MEMS firmware also features a limp-home capability (referred to in the literature as "limited operating strategy") that will substitute a nominal value for any non-operative sensor. [1]

Crankshaft position and speed are determined by input signals generated by poles in a magnetic reluctance disc. The system may be run in either open-loop or closed-loop mode (with the latter requiring a lambda sensor). Additional features include an engine speed limiter, overrun fuel cut-off, startup fuel enrichment (both during cranking and after startup), and fueling compensation for battery voltage. Some operating parameters are learned by the ECU over time, such as the optimal IAC valve position for a stable idle. This accommodates slight differences in engine wear and tune between different engines. [6]

Among the different revisions of MEMS were the following:

Diagnostics

Because it was designed before industry-wide on-board diagnostics were standardized, early versions of MEMS use a proprietary diagnostics protocol and signaling scheme. This protocol is known as ROSCO, which is an abbreviation for Rover Service Communications. [8] On earlier cars, the diagnostic port used a circular three-pin connector (type 172202 manufactured by TE Connectivity), where later cars switched to the standardized 16-pin ISO J1962 connector type.

When the system detects a fault, a corresponding fault code is stored in the ECU's non-volatile memory. Fault codes may only be cleared by commanding the ECU via the diagnostic port. Testing of MEMS equipped cars was originally possible with the "COBEST", "Microcheck", and "Microtune" test equipment provided to Rover dealerships and service centers. [6] [9] The Rover TestBook system later became available to provide similar functionality as well. [2]

There are now various open and closed source applications for PC and mobile phones in order to interact with these ECUs, rather than having to purchase an old Testbook tool.

Related Research Articles

<span class="mw-page-title-main">Fuel injection</span> Feature of internal combustion engines

Fuel injection is the introduction of fuel in an internal combustion engine, most commonly automotive engines, by the means of an injector. This article focuses on fuel injection in reciprocating piston and Wankel rotary engines.

<span class="mw-page-title-main">Ignition system</span> Electric spark system to ignite a fuel-air mixture

Ignition systems are used by heat engines to initiate combustion by igniting the fuel-air mixture. In a spark ignition versions of the internal combustion engine, the ignition system creates a spark to ignite the fuel-air mixture just before each combustion stroke. Gas turbine engines and rocket engines normally use an ignition system only during start-up.

An oxygen sensor (or lambda sensor, where lambda refers to air–fuel equivalence ratio, usually denoted by λ) or probe or sond, is an electronic device that measures the proportion of oxygen (O2) in the gas or liquid being analysed.

MegaSquirt is a general-purpose aftermarket electronic fuel injection (EFI) controller designed to be used with a wide range of spark-ignition internal combustion engines MegaSquirt was designed by Bruce Bowling and Al Grippo in 2001.

<span class="mw-page-title-main">On-board diagnostics</span> Automotive engineering terminology

On-board diagnostics (OBD) is a term referring to a vehicle's self-diagnostic and reporting capability. In the United States, this self diagnostic is a requirement to comply with Federal Emissions standards to detect failures that may increase the vehicle tailpipe emissions to more than 150% of the standard to which it was originally certified.

Jetronic is a trade name of a manifold injection technology for automotive petrol engines, developed and marketed by Robert Bosch GmbH from the 1960s onwards. Bosch licensed the concept to many automobile manufacturers. There are several variations of the technology offering technological development and refinement.

<span class="mw-page-title-main">Chip tuning</span> Reprogramming a car to improve performance

Chip tuning is changing or modifying an erasable programmable read only memory chip in an automobile's or other vehicle's electronic control unit to achieve superior performance, whether it be more power, cleaner emissions, or better fuel efficiency. Engine manufacturers generally use a conservative electronic control unit map to allow for individual engine variations as well as infrequent servicing and poor-quality fuel. Vehicles with a remapped electronic control unit may be more sensitive to fuel quality and service schedules.

<span class="mw-page-title-main">Mass flow sensor</span> Internal combustion engine sensor

A mass (air) flow sensor (MAF) is a sensor used to determine the mass flow rate of air entering a fuel-injected internal combustion engine.

<span class="mw-page-title-main">Engine control unit</span> Computer that adjusts electronics in an internal combustion propulsion system

An engine control unit (ECU), also called an engine control module (ECM), is a device which controls multiple systems of an internal combustion engine in a single unit. Systems commonly controlled by an ECU include the fuel injection and ignition systems.

<span class="mw-page-title-main">Motronic</span>

Motronic is the trade name given to a range of digital engine control units developed by Robert Bosch GmbH which combined control of fuel injection and ignition in a single unit. By controlling both major systems in a single unit, many aspects of the engine's characteristics can be improved.

A throttle is the mechanism by which fluid flow is managed by constriction or obstruction.

Renix was a joint venture by Renault and Bendix that designed and manufactured automobile electronic ignitions, fuel injection systems, electronic automatic transmission controls, and various engine sensors. Major applications included various Renault and Volvo vehicles. The name became synonymous in the U.S. with the computer and fuel injection system used on the AMC/Jeep 2.5 L I4 and 4.0 L I6 engines.

<span class="mw-page-title-main">Digifant engine management system</span>

The Digifant engine management system is an electronic engine control unit (ECU), which monitors and controls the fuel injection and ignition systems in petrol engines, designed by Volkswagen Group, in cooperation with Robert Bosch GmbH.

Trionic T5.5 is an engine management system in the Saab Trionic range. It controls ignition, fuel injection and turbo boost pressure. The system was introduced in the 1993 Saab 9000 2.3 Turbo with B234L and B234R engine.

<span class="mw-page-title-main">Electronic Diesel Control</span>

Electronic Diesel Control is a diesel engine fuel injection control system for the precise metering and delivery of fuel into the combustion chamber of modern diesel engines used in trucks and cars.

Automotive electronics are electronic systems used in vehicles, including engine management, ignition, radio, carputers, telematics, in-car entertainment systems, and others. Ignition, engine and transmission electronics are also found in trucks, motorcycles, off-road vehicles, and other internal combustion powered machinery such as forklifts, tractors and excavators. Related elements for control of relevant electrical systems are also found on hybrid vehicles and electric cars.

<span class="mw-page-title-main">Crankshaft position sensor</span> Import

A crank sensor (CKP) is an electronic device used in an internal combustion engine, both petrol and diesel, to monitor the position or rotational speed of the crankshaft. This information is used by engine management systems to control the fuel injection or the ignition system timing and other engine parameters. Before electronic crank sensors were available, the distributor would have to be manually adjusted to a timing mark on petrol engines.

The Ford EEC or Electronic Engine Control is a series of ECU that was designed and built by Ford Motor Company. The first system, EEC I, used processors and components developed by Toshiba in 1973. It began production in 1974, and went into mass production in 1975. It subsequently went through several model iterations.

<span class="mw-page-title-main">Lucas 14CUX</span>

The Lucas 14CUX is an automotive electronic fuel injection system developed by Lucas Industries and fitted to the Rover V8 engine in Land Rover vehicles between 1990 and 1995. The system was also paired with the Rover V8 by a number of low-volume manufacturers such as TVR, Marcos, Ginetta, and Morgan.

<span class="mw-page-title-main">SECU-3</span>

SECU-3 is an internal combustion engine control unit. It is being developed as an open source project. Anyone can take part in the project, and can access all the information without any registrations.

References

  1. 1 2 3 White, Charles (July 1997). Automotive Engine Management and Fuel Injection Manual. Haynes Techbooks. ISBN   978-1859603444.
  2. 1 2 3 Crabb, D.; Duncan, H.M.; Hiljemark, S.L.; Kershaw, T.J. (14–18 May 1990). MEMS (Modular Engine Management System) (PDF). Twenty-second International Symposium on Automotive Technology and Automation. Florence, Italy: Joint Publications Research Service (published 26 September 1990). pp. 127–134. Retrieved 2014-01-27.
  3. Rees, Chris (2013-08-01). The Magnificent 7. Haynes Publishing. ISBN   978-0857333919.
  4. "MGF MEMS 1.9 ECU". Dieter's MGFcar. Retrieved 2023-05-12.
  5. "Diagnosing and fixing vacuum leaks". Web Memsfcr. Retrieved 2023-05-12.
  6. 1 2 "T16 MEMS Electrics" (PDF).
  7. 1 2 Parker, Roger (2013-01-01). MGF and TF Restoration Manual. The Crowood Press UK. ISBN   978-1847974006.
  8. Williams, Mike (April 1990). "Automotive electronics in Europe -- the real issue is cost" (PDF). Research Newsletter. Dataquest (1990–8). Retrieved 2015-10-12.
  9. Rover Product Training College (1989). Rover MEMS Service (Videotape). Rover Service TV Unit. Retrieved 2014-01-28.