Phosphor thermometry

Last updated November 22, 2023

Phosphor thermometry is an optical method for surface temperature measurement. The method exploits luminescence emitted by phosphor material. Phosphors are fine white or pastel-colored inorganic powders which may be stimulated by any of a variety of means to luminesce, i.e. emit light. Certain characteristics of the emitted light change with temperature, including brightness, color, and afterglow duration. The latter is most commonly used for temperature measurement.

History

The first mention of temperature measurement utilizing a phosphor is in two patents originally filed in 1932 by Paul Neubert.^[1]

Time dependence of luminescence

Typically a short duration ultraviolet lamp or laser source illuminates the phosphor coating which in turn luminesces visibly. When the illuminating source ceases, the luminescence will persist for a characteristic time, steadily decreasing. The time required for the brightness to decrease to 1/e of its original value is known as the decay time or lifetime and signified as $\tau$ . It is a function of temperature, T.

The intensity, I of the luminescence commonly decays exponentially as:

$\!\,I=I_{o}e^{\frac {-t}{\tau }}$

Where I₀ is the initial intensity (or amplitude). The 't' is the time and $\tau$ is parameter which can be temperature dependent.

A temperature sensor based on direct decay time measurement has been shown to reach a temperature from 1000 to as high as 1,600 °C.^[2] In that work, a doped YAG phosphor was grown onto an undoped YAG fiber to form a monolithic structure for the probe, and a laser was used as the excitation source. Subsequently, other versions using LEDs as the excitation source were realized. These devices can measure temperature up to 1,000 °C, and are used in microwave and plasma processing applications.^[3]

If the excitation source is periodic rather than pulsed, then the time response of the luminescence is correspondingly different. For instance, there is a phase difference between a sinusoidally varying light emitting diode (LED) signal of frequency f and the fluorescence that results (see figure). The phase difference varies with decay time and hence temperature as:

$\!\,\phi =tan(2{\pi }f{\tau })$

Temperature dependence of emission lines: intensity ratio

The second method of temperature detection is based on intensity ratios of two separate emission lines; the change in coating temperature is reflected by the change of the phosphorescence spectrum.^[4]^[5] This method enables surface temperature distributions to be measured.^[6] The intensity ratio method has the advantage that polluted optics has little effect on the measurement as it compares ratios between emission lines. The emission lines are equally affected by 'dirty' surfaces or optics.

Temperature dependence

Several observations are pertinent to the figure on the right:

Oxysulfide materials exhibit several different emission lines, each having a different temperature dependence. Substituting one rare-earth for another, in this instance changing La to Gd, shifts the temperature dependence.
The YAG:Cr material (Y₃Al₅O₁₂:Cr³⁺) shows less sensitivity but covers a wider temperature range than the more sensitive materials.
Sometime decay times are constant over a wide range before becoming temperature dependent at some threshold value. This is illustrated for the YVO₄:Dy curve; it also holds for several other materials (not shown in the figure). Manufacturers sometimes add a second rare earth as a sensitizer. This may enhance the emission and alter the nature of the temperature dependence. Also, gallium is sometimes substituted for some of the aluminium in YAG, also altering the temperature dependence.
The emission decay of dysprosium (Dy) phosphors is sometimes non-exponential with time. Consequently, the value assigned to decay time will depend on the analysis method chosen. This non-exponential character often becomes more pronounced as the dopant concentration increases.
In the high-temperature part, the two lutetium phosphate samples are single crystals rather than powders. This has minor effect on decay time and its temperature dependence though. However, the decay time of a given phosphor depends on the particle size, especially below one micrometer.

There are further parameters influencing the luminescence of thermographic phosphors, e.g. the excitation energy, the dopant concentration or the composition or the absolute pressure of the surrounding gas phase. Therefore, care has to be taken in order to keep constant these parameters for all measurements.

Thermographic phosphor application in a thermal barrier coating

A thermal barrier coating (TBC) allows gas turbine components to survive higher temperatures in the hot section of engines, while having acceptable life times. These coatings are thin ceramic coatings (several hundred micrometers) usually based on oxide materials.

Early works considered the integration of luminescent materials as erosion sensors in TBCs.^[7] The notion of a "thermal barrier sensor coating" (sensor TBC) for temperature detection was introduced in 1998. Instead of applying a phosphor layer on the surface where the temperature needs to be measured, it was proposed to locally modify the composition of the TBC so that it acts as a thermographic phosphor as well as a protective thermal barrier. This dual functional material enables surface temperature measurement but also could provide a means to measure temperature within the TBC and at the metal/topcoat interface, hence enabling the manufacturing of an integrated heat flux gauge.^[8] First results on yttria-stabilized zirconia co-doped with europia (YSZ:Eu) powders were published in 2000.^[9] They also demonstrated sub-surface measurements looking through a 50 μm undoped YSZ layer and detecting the phosphorescence of a thin (10 μm) YSZ:Eu layer (bi-layer system) underneath using the ESAVD technique to produce the coating.^[10] The first results on electron beam physical vapour deposition of TBCs were published in 2001.^[11] The coating tested was a monolayer coating of standard YSZ co-doped with dysprosia (YSZ:Dy). First work on industrial atmospheric plasma sprayed (APS) sensor coating systems commenced around 2002 and was published in 2005.^[12] They demonstrated the capabilities of APS sensor coatings for in-situ two-dimensional temperature measurements in burner rigs using a high speed camera system.^[13] Further, temperature measurement capabilities of APS sensor coatings were demonstrated beyond 1400 °C.^[14] Results on multilayer sensing TBCs, enabling simultaneous temperature measurements below and on the surface of the coating, were reported. Such a multilayer coating could also be used as a heat flux gauge in order to monitor the thermal gradient and also to determine the heat flux through the thickness of the TBC under realistic service conditions.^[15]

Applications for thermographic phosphors in TBCs

While the previously mentioned methods are focusing on the temperature detection, the inclusion of phosphorescent materials into the thermal barrier coating can also work as a micro probe to detect the aging mechanisms or changes to other physical parameters that affect the local atomic surroundings of the optical active ion.^[8]^[16] Detection was demonstrated of hot corrosion processes in YSZ due to vanadium attack.^[17]

Related Research Articles

A thermometer is a device that measures temperature or temperature gradient. A thermometer has two important elements: (1) a temperature sensor in which some change occurs with a change in temperature; and (2) some means of converting this change into a numerical value. Thermometers are widely used in technology and industry to monitor processes, in meteorology, in medicine, and in scientific research.

Photoluminescence is light emission from any form of matter after the absorption of photons. It is one of many forms of luminescence and is initiated by photoexcitation, hence the prefix photo-. Following excitation, various relaxation processes typically occur in which other photons are re-radiated. Time periods between absorption and emission may vary: ranging from short femtosecond-regime for emission involving free-carrier plasma in inorganic semiconductors up to milliseconds for phosphoresence processes in molecular systems; and under special circumstances delay of emission may even span to minutes or hours.

A phosphor is a substance that exhibits the phenomenon of luminescence; it emits light when exposed to some type of radiant energy. The term is used both for fluorescent or phosphorescent substances which glow on exposure to ultraviolet or visible light, and cathodoluminescent substances which glow when struck by an electron beam in a cathode-ray tube.

A thermographic camera is a device that creates an image using infrared (IR) radiation, similar to a normal camera that forms an image using visible light. Instead of the 400–700 nanometre (nm) range of the visible light camera, infrared cameras are sensitive to wavelengths from about 1,000 nm to about 14,000 nm (14 μm). The practice of capturing and analyzing the data they provide is called thermography.

Infrared thermography (IRT), thermal video and/or thermal imaging, is a process where a thermal camera captures and creates an image of an object by using infrared radiation emitted from the object in a process, which are examples of infrared imaging science. Thermographic cameras usually detect radiation in the long-infrared range of the electromagnetic spectrum and produce images of that radiation, called thermograms. Since infrared radiation is emitted by all objects with a temperature above absolute zero according to the black body radiation law, thermography makes it possible to see one's environment with or without visible illumination. The amount of radiation emitted by an object increases with temperature; therefore, thermography allows one to see variations in temperature. When viewed through a thermal imaging camera, warm objects stand out well against cooler backgrounds; humans and other warm-blooded animals become easily visible against the environment, day or night. As a result, thermography is particularly useful to the military and other users of surveillance cameras.

<span class="mw-page-title-main">Scintillator</span> Material which glows when excited by ionizing radiation

A scintillator is a material that exhibits scintillation, the property of luminescence, when excited by ionizing radiation. Luminescent materials, when struck by an incoming particle, absorb its energy and scintillate. Sometimes, the excited state is metastable, so the relaxation back down from the excited state to lower states is delayed. The process then corresponds to one of two phenomena: delayed fluorescence or phosphorescence. The correspondence depends on the type of transition and hence the wavelength of the emitted optical photon.

Many ceramic materials, both glassy and crystalline, have found use as optically transparent materials in various forms from bulk solid-state components to high surface area forms such as thin films, coatings, and fibers. Such devices have found widespread use for various applications in the electro-optical field including: optical fibers for guided lightwave transmission, optical switches, laser amplifiers and lenses, hosts for solid-state lasers and optical window materials for gas lasers, and infrared (IR) heat seeking devices for missile guidance systems and IR night vision.

Particle image velocimetry (PIV) is an optical method of flow visualization used in education and research. It is used to obtain instantaneous velocity measurements and related properties in fluids. The fluid is seeded with tracer particles which, for sufficiently small particles, are assumed to faithfully follow the flow dynamics. The fluid with entrained particles is illuminated so that particles are visible. The motion of the seeding particles is used to calculate speed and direction of the flow being studied.

Yttrium aluminium garnet (YAG, Y₃Al₅O₁₂) is a synthetic crystalline material of the garnet group. It is a cubic yttrium aluminium oxide phase, with other examples being YAlO₃ (YAP) in a hexagonal or an orthorhombic, perovskite-like form, and the monoclinic Y₄Al₂O₉ (YAM).

<span class="mw-page-title-main">Yttrium(III) oxide</span> Chemical compound

Yttrium oxide, also known as yttria, is Y₂O₃. It is an air-stable, white solid substance.

A superalloy, or high-performance alloy, is an alloy with the ability to operate at a high fraction of its melting point. Key characteristics of a superalloy include mechanical strength, thermal creep deformation resistance, surface stability, and corrosion and oxidation resistance.

Luminous paint is paint that emits visible light through fluorescence, phosphorescence, or radioluminescence.

Indium(III) oxide (In₂O₃) is a chemical compound, an amphoteric oxide of indium.

Thermal barrier coatings (TBCs) are advanced materials systems usually applied to metallic surfaces on parts operating at elevated temperatures, such as gas turbine combustors and turbines, and in automotive exhaust heat management. These 100 μm to 2 mm thick coatings of thermally insulating materials serve to insulate components from large and prolonged heat loads and can sustain an appreciable temperature difference between the load-bearing alloys and the coating surface. In doing so, these coatings can allow for higher operating temperatures while limiting the thermal exposure of structural components, extending part life by reducing oxidation and thermal fatigue. In conjunction with active film cooling, TBCs permit working fluid temperatures higher than the melting point of the metal airfoil in some turbine applications. Due to increasing demand for more efficient engines running at higher temperatures with better durability/lifetime and thinner coatings to reduce parasitic mass for rotating/moving components, there is significant motivation to develop new and advanced TBCs. The material requirements of TBCs are similar to those of heat shields, although in the latter application emissivity tends to be of greater importance.

Yttria-stabilized zirconia (YSZ) is a ceramic in which the cubic crystal structure of zirconium dioxide is made stable at room temperature by an addition of yttrium oxide. These oxides are commonly called "zirconia" (ZrO₂) and "yttria" (Y₂O₃), hence the name.

Thermographic inspection refers to the nondestructive testing (NDT) of parts, materials or systems through the imaging of the temperature fields, gradients and/or patterns ("thermograms") at the object's surface. It is distinguished from medical thermography by the subjects being examined: thermographic inspection generally examines inanimate objects, while medical thermography generally examines living organisms. Generally, thermographic inspection is performed using an infrared sensor.

A thermal history coating (THC) is a robust coating containing various non-toxic chemical compounds whose crystal structures irreversibly change at high temperatures. This allows for temperature measurements and thermal analysis to be performed on intricate and inaccessible components, which operate in harsh environments. Like thermal barrier coatings, THCs provide protection from intense heat to the surfaces on which they are applied. The temperature range that THCs provide accurate temperature measurements in is 900 °C to 1400 °C with an accuracy of ±10 °C.

<span class="mw-page-title-main">David R. Clarke</span> Material scientist

David R. Clarke is a material scientist and the inaugural Extended Tarr Family Professor of Material Science and Applied Physics at Harvard John A. Paulson School of Engineering and Applied Sciences (SEAS). He is the principal investigator of the Materials Discovery and Applications Group.

Lauren Elizabeth Shea Rohwer is an American scientist. She is a principal member of the technical staff at Sandia National Laboratories. Rohwer researches synthesis and characterization of nanoscale luminescent materials with applications to solid-state lighting.

Piezospectroscopy (also known as photoluminescence piezospectroscopy) is an analytical technique that reveals internal stresses in alumina-containing materials(Al₂O₃, also known as aluminum oxide), particularly thermal barrier coatings (TBCs). A typical procedure involves illuminating the sample with laser light of a known wavelength, causing the material to release its own radiation in response(see fluorescence). By measuring the emitted radiation and comparing the location of the peaks to a stress-free sample, stresses in the material can be revealed without any destructive interaction.

References

↑ Allison, S. W. (2019). A brief history of phosphor thermometry. Measurement Science and Technology, 30(7), 072001.
↑ J.L. Kennedy and N. Djeu (2002), "Operation of Yb:YAG fiber optic temperature sensor up to 1,600°C", Sensors and Actuators A 100, 187-191.
↑ Commercialized by MicroMaterials, Inc. under US Patents 6,045,259 and 9,599,518 B2.
↑ J. P. Feist & A. L. Heyes (2000). "The characterization of Y2O2S:Sm powder as a thermographic phosphor for high temperature applications". Measurement Science and Technology. 11 (7): 942–947. Bibcode:2000MeScT..11..942F. doi:10.1088/0957-0233/11/7/310. S2CID 250917066.
↑ L. P. Goss, A. A. Smith and M. E. Post (1989). "Surface thermometry by laser-induced fluorescence". Review of Scientific Instruments. 60 (12): 3702–3706. Bibcode:1989RScI...60.3702G. doi:10.1063/1.1140478.
↑ J. P. Feist, A. L. Heyes and S. Seefeldt (2003). "Thermographic phosphor thermometry for film cooling studies in gas turbine combustors". Journal of Power and Energy. 217 (2): 193–200. Bibcode:2003PIMEA.217..193F. doi:10.1243/09576500360611227. S2CID 95454730.
↑ K. Amano, H. Takeda, T. Suzuki, M. Tamatani, M. Itoh and Y. Takahashi (1987), "Thermal barrier coating" U.S. Patent 4,774,150
1 2 K-L. Choy, A. L. Heyes and J. Feist (1998), "Thermal barrier coating with thermoluminescent indicator material embedded therein" U.S. Patent 6,974,641
↑ J. P. Feist & A. L. Heyes (2000). "Europium-doped yttria-stabilized zirconia for high-temperature phosphor thermometry". Proceedings of the Institution of Mechanical Engineers . 214, Part L: 7–11.
↑ K-L. Choy; J. P. Feist; A. L. Heyes; B. Su (1999). "Eu-doped Y2O3 phosphor films produced by electrostatic-assisted chemical vapor deposition". Journal of Materials Research. 14 (7): 3111–3114. Bibcode:1999JMatR..14.3111C. doi:10.1557/JMR.1999.0417. S2CID 98365100.
↑ J. P. Feist, A. L. Heyes and J. R. Nicholls (2001). "Phosphor thermometry in an electron beam physical vapour deposition produced thermal barrier coating doped with dysprosium". Proceedings of the Institution of Mechanical Engineers. 215 Part G (6): 333–340. doi:10.1243/0954410011533338. S2CID 137294920.
↑ X. Chen; Z. Mutasim; J. Price; J. P. Feist; A. L. Heyes; S. Seefeldt (2005). "Industrial sensor TBCs: Studies on temperature detection and durability". International Journal of Applied Ceramic Technology. 2 (5): 414–421. doi:10.1111/j.1744-7402.2005.02042.x.
↑ A. L. Heyes; S. Seefeldt; J. P Feist (2005). "Two-colour thermometry for surface temperature measurement". Optics and Laser Technology. 38 (4–6): 257–265. Bibcode:2006OptLT..38..257H. doi:10.1016/j.optlastec.2005.06.012.
↑ J. P. Feist, J. R. Nicholls, M. J. Fraser, A. L. Heyes (2006) "Luminescent material compositions and structures incorporating the same" Patent PCT/GB2006/003177
↑ R.J.L. Steenbakker; J.P. Feist; R.G. Wellmann; J.R. Nicholls (2008). Sensro TBCs: remote in-situ condition monitoring of EB-PVD coatings at elevated temperatures, GT2008-51192. Proceedings of ASME Turbo Expo 2008: Power for Land, Sea and Air, June 9–13, Berlin, Germany. doi:10.1115/GT2008-51192.
↑ A. M. Srivastava, A. A. Setlur, H. A. Comanzo, J. W. Devitt, J. A. Ruud and L. N. Brewer (2001)"Apparatus for determining past-service conditions and remaining life of thermal barrier coatings and components having such coatings" U.S. Patent 6730918B2
↑ J. P. Feist and A. L. Heyes (2003) "Coatings and an optical method for detecting corrosion process in coatings" GB. Patent 0318929.7