| RWD 4 | |
|---|---|
 | |
| Role | Sports plane |
| Manufacturer | Warsaw University of Technology workshops |
| Designer | RWD team |
| First flight | Spring 1930 |
| Introduction | 1930 |
| Retired | 1936 |
| Primary user | Poland |
| Produced | 1930 |
| Number built | 9 |
The RWD 4 was a Polish sports plane of 1930, constructed by the RWD team.
The RWD 4 was constructed by the RWD team of Stanisław Rogalski, Stanisław Wigura and Jerzy Drzewiecki in Warsaw. It was based upon their earlier RWD 2 design, but enlarged and fitted with more powerful inline engine. It retained the same fish-shaped fuselage without a direct view forward from the pilot's seat, though the view improved due to thin fuselage profile before the pilot. Also a silhouette became slimmer. The aircraft development was ordered by the Ministry of Communication especially for participation in the Challenge 1930 international air competition. At the same time, the RWD developed similar liaison aircraft project, the RWD 3, which shared many features with the RWD 4.
The first three aircraft (registration SP-ADK, -ADL and -ADM) were completed and flown by the designer Jerzy Drzewiecki in early 1930. In late 1930, a further six aircraft were built for the Polish Aero Club (registration SP-AEK, -AEL, AEY, -AEZ, -AFC, -AGP).
The first three aircraft took part in the Challenge 1930 competition in July. Only Jerzy Bajan completed the race on SP-ADM on the 32nd place (of 35 classified and 60 starting crews). Franciszek Żwirko (flying with Stanisław Wigura) withdrew due to engine failure, while the third pilot Tadeusz Karpiński withdrew due to illness.
RWD 4s were later used in Polish local air competitions, with some success (for example, F. Żwirko won the 3rd Polish Light Aircraft Contest in 1930, and other RWD 4s took the 2nd, 5th and 6th place). In 1931, in an international air meeting in Zagreb, Jerzy Bajan won 2nd place overall and the 1st place in aerobatics. RWD 4s were also used for training and glider towing in regional aero clubs. The first two were withdrawn in 1931, the last were scrapped in 1936, after quite short, but meritorious service in Polish sporting aviation.
Wooden construction sports plane, conventional in layout, high-wing cantilever monoplane. The fuselage rectangular in cross-section (narrower in upper part), plywood-covered. Trapezoid one-part wing, canvas and plywood covered. A crew of two, sitting in tandem in the fuselage, with dual controls. The cockpits were open to the sides, with individual doors on the right. Principally powered by a 4-cylinder air-cooled 115 hp Cirrus Hermes straight engine (105 hp nominal power, 115 hp take-off power), driving a two-blade wooden propeller, the aircraft was also known to be fitted with 85 hp Cirrus III and 105 hp de Havilland Gipsy II engines. Landing gear was conventional, fixed, with a rear skid. The fuel tank capacity was 110 litres held in-wing giving fuel consumption of 21 litres per hour.
Data fromPolish aircraft, 1893-1939 [1]
General characteristics
Performance
Related development
The RWD 6 was a Polish sports plane of 1932, constructed by the RWD team. It was a winner of the Challenge 1932 international tourist aircraft contest.
The RWD 5 was a Polish touring and sports plane of 1931, a two-seat high-wing monoplane, constructed by the RWD team. It was made famous by its transatlantic flight, being the smallest aircraft to cross the Atlantic.
The RWD 7 was a Polish sports plane of 1931, constructed by the RWD team.
The RWD 8 was a Polish parasol wing monoplane trainer aircraft produced by RWD. It was used from 1934 to 1939 by the Polish Air Force and civilian aviation.
The RWD-14 Czapla was a Polish army cooperation aircraft, designed in the mid-1930s by the RWD team, and produced in the LWS factory from 1938. A series of 65 aircraft were built and most were used by the Polish Air Force observation squadrons during World War II in 1939.
The LWS-2 was the Polish air ambulance aircraft prototype, designed in the late-1930s in the LWS factory.
The RWD 2 was a 1929 Polish single-engine high-wing monoplane sports plane constructed by the RWD team.
The RWD 3 was a 1930 Polish sports aircraft and liaison aircraft prototype, constructed by the RWD team, a single-engine high-wing monoplane.
The RWD 1 was a Polish sports plane of 1928, a single-engine high-wing monoplane constructed by the RWD design team.
The RWD-10 was a Polish aerobatics sports plane, single-seat parasol wing monoplane, used from 1933 to 1939 and constructed by the RWD team.
The RWD 9 was a Polish sports plane of 1934, constructed by the RWD team.
PZL.19 was a Polish sports aircraft built in 1932 in the PZL works. Ordered by the Ministry of Communications, it was specifically designed for the upcoming Challenge 1932 contest held that year in Germany.
The PWS-21 was a Polish passenger aircraft for 4 passengers, built in PWS factory in 1930, that remained a prototype.
The RWD 23 was a Polish low-wing trainer aircraft of 1938, constructed by the RWD team, that remained a prototype.
The JD-2 was a Polish sports plane of 1926. It was the first sports plane designed in Poland, that was built in a small series.
The RWD 16bis and RWD 21 were Polish two-seat low-wing touring and sports planes of the late 1930s, constructed by the RWD bureau, sharing the same construction, main difference of the RWD 21 being a stronger engine.
The RWD-19 was a Polish two-seat low-wing sports aircraft of 1938, constructed by the RWD bureau.
The PWS-11 was a Polish aerobatic and trainer aircraft, developed in 1928-1929 by PWS, which remained a prototype.
The Rogalski and Wigura R.W.1 was designed and built by a pair of students at Warsaw Technical University in 1927. The single example was a two-seat parasol-wing monoplane which entered two national competitions, served the Warsaw Academic Aeroclub and also towed an advertising banner.
The WT-1 was a 1931 high performance sports aircraft designed in Poland. It only made two flights.
