Radlock Trainer

Last updated

Radlock Trainer
RoleSingle seat primary glider
National origin UK
Manufacturermembers of the Hull Experimental Gliding Club
DesignerJ. E. Raddings and W. E. Locke
First flight1932
Number built1

The Radlock Trainer was a single seat primary glider designed and built by members of the Hull Experimental Gliding Club as a basic trainer for their own use in the early 1930s. It was a simple, single exposed seat, wooden glider with a parasol wing.

Contents

Design and development

In 1931 two members of the Hedon-based Hull Experimental Gliding Club designed a single-seat primary glider, known as the Radlock glider from a conjunction of their names, Raddings and Locke. [1] The designers worked for Blackburn Aeroplane and Motor Co., Ltd., based at Brough near Hull. [2] The club had a workshop at Hessle and the glider was built there by members during 1931-1932. [1]

The Radlock glider had a wing of rectangular plan built around two spars. It carried ailerons but no flaps or airbrakes. The wing was attached high above the fuselage by a pair of lift struts, one from the upper fuselage to the forward spar and the other reaching forwards from the lower fuselage member, behind the wing trailing edge, to the aft spar. Both lift struts joined the wing at about mid-span. The centre section was braced with a single N-form set of struts and these also provided a base for a triangular kingpost above the wing, from which a pair of landing wires on each side ran to the spars at mid-span. [1]

The fuselage was simple, very narrow and shallow, being formed from two members, one above the other and joined by short X-shaped webs. [1] [2] The pilot sat below the leading edge of the wing, his seat and controls on a short platform attached to the upper fuselage member. [3] [4] There was a short, square fin with the triangular tailplane on top of it. The rudder was almost twice the height of the fin and reached down to the lower fuselage, moving in a cut-out between the elevators. The rear of the fuselage was laterally braced by a pair of wires from the rear spar at the tops of the lift strut to the rear end of the lower fuselage member. [1] [5]

Originally the Radlock landed on the skid-shaped lower fuselage member, though later a simple pair of wheels was added for auto-towed launches. [1] A photograph taken before September 1932 may show the wheels in place before the tail covering was complete. [2] There was a tail bumper. [1]

Operational history

The first flight was made in 1932. No BGA Certificate of Airworthiness number was recorded. [1] The Radlock seems to have been in regular use with the Hull G.C. at Hedon in 1933, [3] with auto-launches for free flights and auto-towing for training. It is not known how long it remained in service.

Specifications

Data from British Gliders and Sailplanes 1922-1970 [1]

General characteristics


Related Research Articles

Schneider Grunau 9

The ESG Grunau 9, later known as the ESG 29 and post-1933 as the DFS 108-10, was one of the first primary gliders, built in Germany from the late 1920s. It was widely sold.

Abbott-Baynes Scud 1

The Abbott-Baynes Scud 1 was a parasol-winged single seat glider intended to introduce pilots to soaring flight. It was built in the United Kingdom and first flew in 1931.

Abbott-Baynes Scud 2

The Abbott-Baynes Scud 2 was a 1930s high-performance sailplane, built in the UK. It was a development of the intermediate-level Scud 1 with a new, high aspect ratio wing.

The Addyman Zephyr was a one-off, single-seat sailplane designed and built by Erik Addyman in the UK for his own use in the 1930s.

The Czerwiński Sparrow, sometimes known as the de Havilland Canada glider, was a single seat glider, designed and built by a group of de Haviiland engineers in Canada in 1942. It was intended to popularise gliding and be suitable for both basic training and thermal soaring.

The Cramlington Cramcraft was a simple, single-seat, primary training glider, designed in the United Kingdom in 1930. About three were built.

The Payne I.C.1 was a primary glider built by members of a University gliding club in 1930. It was finished and prepared for flight but was damaged by wind and repairs were never completed.

The Penrose Pegasus was a 1930s high-wing, single-seat, wooden glider from the UK. Designed, built and flown by Harald Penrose until the start of World War II, only one was built at the time though a reproduction was constructed in the 1990s.

The Reynard R.4 Primary was an open seat primary glider with an open girder fuselage and a high, wire braced wing. It was designed and built in the UK in 1930 and a few served Gliding Clubs in England and Ireland.

The Czerwiński-Shenstone Harbinger, aka the Shenstone-Czerwiński Harbinger or the Shenstone Harbinger was a Canadian high performance tandem seat sailplane designed in Canada. Only two were built, one in the UK and one in Canada. The latter did not fly until 1975, being under construction for 26 years; the former remained active until at least 1994.

The Stedman TS-1 City of Leeds was a parasol wing wooden sailplane, seating two in tandem open cockpits. Only one was built, by its designer in 1934; it remained active until the outbreak of World War II.

The Bonomi BS.11 Milano and BS.12 Roma were primary gliders designed and built in Italy in the 1930s. Only about six were produced.

The Bonomi BS.16 Allievo Bonomi was a single seat primary glider, designed and built in Italy in 1930 and widely used by flying clubs.

The Bonomi BS.24 Biposto Rome was an Italian dual control trainer designed for club use. Six were built in the mid-1930s.

The CAT 15 was a single-seat primary glider built in Italy just before the Second World War. Only one was constructed.

RRG Prüfling

The 1926 German RRG Prüfling of 1926 was a secondary training glider designed for club use. Plans were sold and it was built in Germany and across the world.

Grüne Post

The Grüne Post was a secondary trainer glider designed by Alexander Lippisch at the request of a German newspaper, the Grüne Post, who distributed plans. Many were built by amateur groups.

Jacobs Hols der Teufel

The Jacobs Hols der Teufel was a single seat trainer glider produced in complete and plan forms in Germany from 1928. It was built and used worldwide.

Schleicher Poppenhausen

The Schleicher Poppenhausen named after the town of Poppenhausen was a two-seat glider, available as a dual control advanced trainer, produced in Germany from 1928.

WS Czajka Polish secondary training glider

The Czajka or Kocjan Czajka after its designer was a Polish secondary training glider which was in continuous production from 1931 to the start of World War II. More than 160 were completed in Warsztaty Szybowcowe in Warsaw.

References

  1. 1 2 3 4 5 6 7 8 9 Ellison, Norman (1971). British Gliders and Sailplanes. London: A & C Black Ltd. p. 155. ISBN   978-0-7136-1189-2.
  2. 1 2 3 "News from the Clubs" (PDF). The Sailplane & Glider. 3 (16): 192. 9 September 1932.
  3. 1 2 "News from the Clubs" (PDF). The Sailplane & Glider. 4 (3): 35. 17 February 1933.
  4. ↑ "News from the Clubs" (PDF). The Sailplane & Glider. 4 (8): 94. 28 April 1933. Archived from the original (PDF) on 30 September 2011.
  5. ↑ "News from the Clubs" (PDF). The Sailplane & Glider. 3 (20): 239. 11 November 1932.
This page is based on this Wikipedia article
Text is available under the CC BY-SA 4.0 license; additional terms may apply.
Images, videos and audio are available under their respective licenses.