| Rapp Rp III | |
|---|---|
 | |
| Rapp Rp III aircraft engine, intake side | |
| Type | Inline piston engine |
| National origin | Germany |
| Manufacturer | Rapp Motorenwerke |
| First run | c.1914 |
| Major applications | Lohner L |
| Developed from | Rapp 100 hp |
The Rapp Rp III was a six-cylinder, SOHC valvetrain water-cooled inline aircraft engine built by Rapp Motorenwerke. Its design had been based on the previous Rapp 100 hp four-cylinder engine.
When the Rapp Motorenwerke were founded on 27 October 1913 Karl Rapp immediately concentrated on designing new aircraft engines. Besides the Rapp 100 hp four-cylinder, an improved version of FD 1416 engine he had designed previously at Flugwerk Deutschland, he also worked on an 125 hp (93 kW) six-cylinder aircraft engine for the second Kaiserpreis contest for aviation engines. [1] This 125 hp engine however was not completed on time for the Kaiserpreis and further development led to the 150 hp Rapp six-cylinder engine in 1914. [1] The early 150 hp version of this engine was said to have developed roughly around 150 hp (112 kW) [2] [3] up to 160 hp (119 kW) [4] at 1,300–1,400 rpm and weighing about 260–265 kg (573–584 lb), [2] [3] [4] while the later versions were said to have developed about 170-175 hp [5] [6] and weighing around 290 kg. [5] [6]
The engine had its cylinders arranged in pairs, with two separate steel cylinder liners screwed into the pairwise cast cylinder heads. The cylinder heads had integral cooling jackets and were cast from steel in pairs and then machined. [7] [8] The valve seats, with the exhaust valve seats being water-cooled, were separately built parts which were screwed into the cylinder heads and could be easily removed for maintenance work. Both inlet valves of the cylinder pair, and likewise so both exhaust valves on the other side, were pressed into their seat by a single pivoted leaf spring each. The exhaust and inlet valves were actuated successively from a single cam on the overhead camshaft via roller tappets and rocker arms. [8]
The camshaft was driven via a vertical timing shaft and bevel gears between the last two cylinder pairs. Two magnetos provided sparks for the two spark plugs per cylinder and likewise were located between the last two cylinder pairs, also driven from the vertical timing shaft. This arrangement had already been used on Karl Rapp's earlier four-cylinder engine, but contrary to the four-cylinder design, on the six-cylinder engine the additional spacing between the last two cylinder pairs led to an asymmetry in the crankshaft and cylinder arrangement. This asymmetry is believed to have been the major contributor to the severe vibration and longevity problems that the engine had been plagued with.
It appears that this position of the vertical timing shaft had been chosen deliberately in order to keep the pairwise cylinder design while at the same time positioning the magnetos away from the rear end of the engine, complying army administration considerations for avoiding interference on the compass. [9] [8] [7]
The engine case was cast from aluminum in two pieces, parted at the center line in an upper and a lower part. The crankshaft was supported after every two cylinders by the four main journals in the upper part of the crankcase. [10] Lubrication was done by a gear pump which was mounted on the lowest point of the engine. The gear pump fed the oil from a heat permeable cylindrical brass oil reservoir below the engine crankcase to the main journals of the crankshaft, from where it passed on to the rod journals and gudgeon pins through drilled ducts. [9] The proper oil level in the oil reservoir was maintained by an eccentric pump through augmentation of fresh oil and an additional eccentric pump removed excessive oil from the crankcase in case of an inclined engine position. [9] [8] [10] A gear water pump for circulating the engine coolant was also located below the crankcase. [10]
The first engines had two Zenith-type [10] carburettors located at the rear end of the cylinder row, from where they fed the cylinders via two separate pipes, which were conjoined approximately at cylinder three. On later models this arrangement had been given up and the two Zenith carburettors were the relocated to the more conventional position on the left side of the cylinder block, with each of them feeding three cylinders. An in-flight adjustable amount of pre-heated air could be provided to the carburettors via admission pipes routed through the exhaust.
While the Prussian Army Administration rejected the first delivery of these engines as unsuitable, the Bavarian Army Administration and the German Imperial Navy administration continued to order Rapp engines in limited amounts. [1] Also the Austro-Hungarian Armed Forces and especially the Austro-Hungarian Navy administration, being in dire need for engines for their flying boats, ordered Rapp engines. [1] Engine troubles however prevented a greater success of the engine, with the most severe problems being engine roughness and vibrations, frequently damaged bearings and problems with the carburetion. [1]
In response to a commission for 40 Rapp Rp III engines from the German military authorities, for which the military authorities demanded a power output of at least 175 hp at the acceptance test, [1] Karl Rapp increased the output of his engine accordingly, with further strengthening of the engine resulting in additional weight and increasing vibration problems. It appears that some authors refer to this engine as 175 hp (130 kW) Rapp Rp IIIa, [11] while others still refer to it as Rapp Rp III. [6] [12]
The acceptance test in January 1916 turned out to be a failure, with the engines crankshaft breaking after several test runs with a total duration of 32 hours. [1] As a result, also the Bavarian Army Administration a well as the Austrian Army Administration withdrew from ordering further Rapp engines, with the Austro-Hungarian Navy administration remaining the only customer. [1]
Data fromHuth [6]
Related development
Related lists
The Gotha G.I was a heavy bomber used by the Luftstreitkräfte during World War I.
The Albatros C.I,, was the first of the successful C-series of two-seat general-purpose biplanes built by Albatros Flugzeugwerke during World War I. Based on the unarmed Albatros B.II, the C.I reversed the pilot and observer seating so that the observer occupied the rear cockpit which was fitted with a ring-mounted 7.92 mm (0.312 in) Parabellum MG14 machine gun.
The Mercedes D.III, or F1466 as it was known internally, was a six-cylinder SOHC valvetrain liquid-cooled inline aircraft engine built by Daimler and used on a wide variety of German aircraft during World War I. The initial versions were introduced in 1914 at 160 hp, but a series of changes improved this to 170 hp in 1917, and 180 by mid-1918. These later models were used on almost all late-war German fighters, and its only real competition, the BMW III, was available only in very limited numbers. Compared to the Allied engines it faced, the D.III was generally outdated.
The Mercedes D.II was a six-cylinder, SOHC valvetrain liquid-cooled inline aircraft engine built by Daimler during the early stages of World War I. Producing about 110 to 120 hp, it was at the low-end of the power range of contemporary engines, and was generally outperformed by rotaries whose power-to-weight ratio tended to be much better. It also had stiff competition from the Ferdinand Porsche-designed 120 hp Austro-Daimler 6. The D.II was produced only briefly as a result, but its design formed the basis for the later Mercedes D.III which saw widespread use throughout the war.
The Benz Bz.IV was a German six-cylinder, water-cooled, inline engine developed for aircraft use. Deliveries began in 1916, and some 6,400 were produced.
The Benz Bz.III was a six-cylinder, water-cooled, inline engine developed in Germany for use in aircraft in 1914. Developing 112 kW (150 hp) at 1,400 rpm from 14.3 L, it powered many German military aircraft during World War I. It was replaced in production by the unrelated Benz Bz.IIIa. and eventually the V-8 Benz Bz.IIIb. The Benz Bz.III was built under licence in Sweden by AB Thulinverken, known as the Thulin E.
The Austro-Daimler 6 was a series of Austrian six-cylinder water-cooled inline SOHC aero engines first produced in 1910 by the Austro-Daimler company.
Rapp Motorenwerke GmbH was a German aircraft engine manufacturer based in Munich, Bavaria. Founded in 1913, the firm changed its name in 1917 to Bayerische Motoren Werke GmbH (BMW). The company later became known as Süddeutsche Bremsen-AG after its engine-production assets and the BMW name were transferred in 1922 to Bayerische Flugzeugwerke, which was then renamed to Bayerische Motoren Werke AG and subsequently evolved into the automotive manufacturer known today as BMW.
The 1913 20-cylinder Anzani air-cooled radial engine was the first four row radial and one of the most powerful engines of its period, though few were used.
The Argus As I was a four-cylinder, water-cooled, aircraft engine produced in Germany by Argus Motoren from 1911 until about 1913.
The Argus As II was a six-cylinder, in-line, water-cooled, aircraft engine produced in Germany by Argus Motoren in 1914. The Argus As II produced 120 hp (89 kW) at 1,350 rpm.
The Conrad C.III was a six-cylinder, water-cooled inline aircraft engine designed by Robert Conrad. It was used on some German training aircraft during World War I. The engine was mainly produced under license by the German Nationale Automobil Gesellschaft.
The Argus As III was a six-cylinder, in-line, water-cooled, aircraft engine produced in Germany by Argus Motoren during World War I. The Argus As III produced 180 hp (130 kW) at 1,400 rpm.
The Renault 100 hp aircraft engine from 1912 was a twelve-cylinder, air cooled 60° vee engine built by the French Renault company.
The Argus 140/150 hp 6-cylinder aircraft engine from 1913 was a six-cylinder, water cooled inline engine built by the German Argus Motoren company from 1913 to 1914.
The Argus 140/150 hp aircraft engine from 1911, also known as Argus Type IV, was a four-cylinder, water cooled inline engine built by the German Argus Motoren company.
The Argus 70 hp aircraft engine, aka Argus Type I from 1911 was a four-cylinder, water cooled inline engine built by the German Argus Motoren company. The engine also was license produced in France by Automobiles Rossel and sold in France under the brand names 'Aviatik' and 'Aviatic-Rossel' by Louis Clément, the local sales representative of the Automobil und Aviatik AG.
The Rapp 100 hp was a four-cylinder, SOHC valvetrain liquid-cooled inline aircraft engine built by Rapp Motorenwerke. The engine originated from Karl Rapp's earlier 90 hp four-cylinder that he had designed at the Flugwerk Deutschland GmbH for the 1912/13 Kaiserpreis aircraft engine contest.
The Rapp 125/145 hp, also referred to as Rapp Rp II, was a water-cooled 90° V-8 aircraft engine built by Rapp Motorenwerke in 1915.
The Rapp 200 hp was a water-cooled 90° V-8 aircraft engine built by Rapp Motorenwerke.
