Reynard R.4 Primary

Last updated

R.4 Primary
Role Primary glider
National origin United Kingdom
ManufacturerReynard Gliders, Leicester
First flight1930
Number builtat least 5
Unit cost
£45 in 1931

The Reynard R.4 Primary was an open seat primary glider with an open girder fuselage and a high, wire braced wing. It was designed and built in the UK in 1930 and a few served Gliding Clubs in England and Ireland.

Contents

Design and development

Like other primary gliders, the Reynard R.4 Primary was a simple, wooden, robust design, not intended for high performance.

The wing was rectangular in plan, with ailerons at the tips but no flaps or airbrakes. N-form struts from the wing supported a girder about 8.5 ft (2.6 m) long and curved on the underside to form a landing skid. The pilot's seat and controls were placed, exposed, on its upper surface just ahead of the wing. Lift wires ran from this girder to the underside of the wing beyond mid-span and a pair of landing wires on each side were fixed to the apex of a two strut, triangular central cabane or kingpost above the wing. [1]

Behind the wing trailing edge and the end of the lower girder the rear fuselage was a tapering, vertically orientated, two bay Warren truss, ending at a vertical cross member which supported the rudder. The triangular tailplane and fin were mounted on the horizontal upper fuselage beam and the straight edged rudder extended down through a cut-out between the elevators to the lower beam. [1]

Some Reynards were built with a hinged nacelle to give the pilot better protection from the weather, though still in an open cockpit. To compensate for the extra side area the rear two bays of the fuselage were fabric covered. [1] [2]

It has been suggested [1] that at least two R.4s were built with steel tubed rather than wooden rear fuselages, under the name Reynolds R.4 after the contemporary bicycle tube frame manufacturer.

Operational history

The Reynard could be bought complete for £45 or built from plans costing 21/- (1 guinea or £1.05) and was regularly advertised in 1930-1. [3] Several were built and active in the early 1930s with UK gliding clubs. One was demonstrated to the Leeds club in October 1930 [4] and they received the first of two the following month. [5] The Bradford, [6] Halifax, Leicester [7] and Ulster [8] Gliding Clubs also had Reynards. The two Reynards that received BGA certificates of airworthiness, BGA 166 and 167 had serial number R.4/5 and R.4/6 respectively [1] BGA 166 was used by the Leeds and later Bradford Gliding Clubs. BGA 167 was used by the Ulster Gliding Club from 1931, they fitted a nacelle when they rebuilt it aircraft in 1933. [9] This glider went to the Dublin Gliding Club in 1934 and was still active the following year. [10]

Specifications

Data from British Gliders and Sailplanes 1920-1972 [1]

General characteristics


Related Research Articles

Abbott-Baynes Scud 1

The Abbott-Baynes Scud 1 was a parasol-winged single seat glider intended to introduce pilots to soaring flight. It was built in the United Kingdom and first flew in 1931.

Abbott-Baynes Scud 2

The Abbott-Baynes Scud 2 was a 1930s high-performance sailplane, built in the UK. It was a development of the intermediate-level Scud 1 with a new, high aspect ratio wing.

The Addyman STG was a single seat primary glider, amateur designed and built in the United Kingdom in the mid-1930s.

The Addyman Zephyr was a one-off, single-seat sailplane designed and built by Erik Addyman in the UK for his own use in the 1930s.

The Cloudcraft Dickson Primary was a single-seat primary glider designed in the United Kingdom in 1930 to be constructed from plans. Many glider clubs in the UK and the British Empire flew them in the 1930s.

The Cramlington Cramcraft was a simple, single-seat, primary training glider, designed in the United Kingdom in 1930. About three were built.

The Manuel VI Primary was a wire-braced monoplane primary glider designed and built by W L. (Bill) Manuel whilst serving in the RAF in 1930. It flew successfully but only one was built.

Manuel Wren

The Manuel Crested and Willow Wrens formed a series of wooden, single-seat gliders designed in the UK by W. L. Manuel in the early 1930s, intended for slope soaring. Some were built by the designer, others from plans he supplied. The Dunstable Kestrel was a further development.

The Payne I.C.1 was a primary glider built by members of a University gliding club in 1930. It was finished and prepared for flight but was damaged by wind and repairs were never completed.

The Penrose Pegasus was a 1930s high-wing, single-seat, wooden glider from the UK. Designed, built and flown by Harald Penrose until the start of World War II, only one was built at the time though a reproduction was constructed in the 1990s.

The Radlock Trainer was a single seat primary glider designed and built by members of the Hull Experimental Gliding Club as a basic trainer for their own use in the early 1930s. It was a simple, single exposed seat, wooden glider with a parasol wing.

Scott Viking 1

The Scott Viking 1 was a single seat, high-performance glider designed and built in the UK just before the Second World War. Only four were constructed, one setting records in Argentina and another remaining active into the 1980s.

The Bonomi BS.24 Biposto Rome was an Italian dual control trainer designed for club use. Six were built in the mid-1930s.

The CAT 15 was a single-seat primary glider built in Italy just before the Second World War. Only one was constructed.

The Teichfuss Allievo Pavullo was an Italian single seat open frame primary glider, designed by Luigi Teichfuss of Pavullo and first flown in 1940. It was sold in two versions, strut and cable braced. A single two seat variant was also built.

RRG Prüfling

The 1926 German RRG Prüfling of 1926 was a secondary training glider designed for club use. Plans were sold and it was built in Germany and across the world.

Jacobs Hols der Teufel

The Jacobs Hols der Teufel was a single seat trainer glider produced in complete and plan forms in Germany from 1928. It was built and used worldwide.

Schleicher Poppenhausen

The Schleicher Poppenhausen named after the town of Poppenhausen was a two-seat glider, available as a dual control advanced trainer, produced in Germany from 1928.

WS Czajka Polish secondary training glider

The Czajka or Kocjan Czajka after its designer was a Polish secondary training glider which was in continuous production from 1931 to the start of World War II. More than 160 were completed in Warsztaty Szybowcowe in Warsaw.

Leonard LPT

The Leonard glider was an open frame primary glider, available in the standard single seat form or, unusually, as a two-seater. It was marketed in the U.S. in the early 1930s.

References

  1. 1 2 3 4 5 6 Ellison, Norman (1971). British Gliders and Sailplanes. London: A & C Black Ltd. pp. 161–2. ISBN   978-0-7136-1189-2.
  2. ↑ "From the Clubs" (PDF). The Sailplane & Glider. 3 (9): 108. 2 May 1932.
  3. ↑ "What is a Glider?" (PDF). Gliding Yearbook: 1. 1931.
  4. ↑ "From the Clubs" (PDF). The Sailplane & Glider. 1 (8): 65. 24 October 1930.
  5. ↑ "Gliding". Flight . Vol. XXII no. 48. 28 November 1930. p. 1380.
  6. ↑ "From the Clubs" (PDF). The Sailplane & Glider. 4 (6): 70. 31 March 1933.
  7. ↑ "What is a Glider?" (PDF). Gliding Yearbook: 77–8. 1931.
  8. 1 2 "What is a Glider?" (PDF). Gliding Yearbook: 54. 1931.
  9. ↑ "Giding in Ireland". Wavelength - Journal of the Ulster Gliding Club (60). July 2005.
  10. ↑ "News from the Clubs – Irish gliding" (PDF). The Sailplane & Glider. 21 (5): 20. 5 May 1953.


This page is based on this Wikipedia article
Text is available under the CC BY-SA 4.0 license; additional terms may apply.
Images, videos and audio are available under their respective licenses.