Rubik R-16 Lepke

Last updated
R-16 Lepke
Airport, airplane, sailplane, Hungarian brand Fortepan 59725.jpg
RoleSingle seat basic training glider
National origin Hungary
ManufacturerSportárutermelő Vállalat, Esztergom
Designer Ernő Rubik
First flightSummer1949
Retiredmid-1960s
Number built66

The Rubik R-16 Lepke (Butterfly) was a single seat Hungarian training glider designed to follow the very similar but two seat Rubik R-15 Koma in a winch-launch training programme. The Lepke provided solo experience of the techniques learned with an instructor in an aircraft with similar handling characteristics. That done, the Lepke could be used as a standard trainer to take its pilot to C-certificate level. The pair were widely used by Hungarian glider clubs post-war, with sixty-five of each produced.

Contents

Design and development

In 1940 Ernő Rubik began to consider a glider flight training programme based on a pair of aircraft with similar flight characteristics and sharing many components but differing in their seating. Students would begin on the R-15 Koma, with side-by-side seating and the reassurance and guidance of a tutor watching, then go solo on the R-16 Lepke. During the war, the Hungarian National Aviation Association (Országos Magyar Repülö Egyesület or OMRE) chose to use his R-11 Cimbora and the Koma and Lepke designs were shelved until, in 1948, OMRE announced a competition for single seat and two seat trainers. By the end of the year Rubik's two designs had been chosen. The prototype Koma first flew in the spring of 1949, followed by the Lepke in the summer. [1]

The Lapke was a pod-and-boom glider with a high wing mounted over the front end of the boom and braced with inverted-V struts from the lower fuselage to the spar. The wing was rectangular in plan out to rounded tips and had 3° of dihedral. It was built around a single, wooden spar with wooden ribs; ply covering ahead of the spar formed a torsion-resistant D-box. The rest of the wing was fabric-covered. Diagonal drag struts near the root were made from steel tubes. Constant chord Handley Page slotted ailerons filled the outer half-spans, as on the Koma, but the high-wing Lepka did not need the Koma's flaps. Its wingspan was 4 m (13 ft 1 in) less than that of the heavier Koma. As on the Koma, the wings could be folded back alongside the fuselage once the horizontal tail had been folded upwards. [1] [2]

The forward pod was built around a box-section beam which projected forward to the nose, together with a frame and longerons . The beam carried the single seat in an open cockpit, locally ply-covered and with a removable ply cover fitted with a windshield, around the pilot. Elsewhere the pod was fabric-covered. From the aft of the beam a metal tube strut reached upwards and rearwards to support the boom that formed the rear fuselage. This tube, which was more steeply angled than on the 13% longer Koma, gave the pod a more abrupt rear end. The end of the fuselage beam also mounted an exposed monowheel, assisted by a short, rubber sprung landing skid ahead of it. The tailboom was a horizontal, rectangular section, wooden, ply-covered structure mounted under the centre of the wing spar and braced with wires from mid-span to the tail as well as the steel tube. The Lepke had a conventional tail with a narrow, vertically edged fin. Compared with the Koma, fin area was reduced but the roughly triangular rudder was similar. Its strut-braced horizontal tail was rectangular with rounded tips and of higher aspect ratio than the Koma. The fixed surfaces were wooden but control surfaces were light-metal structures with fabric covering. [1] [2]

The prototype R-16 Lepke first flew at Esztergom in the summer of 1949. A series of sixty-five slightly modified R-16bs followed over 1952-3 and these became the standard Hungarian single-seat trainer; once launching was mastered, pilots continued in the Lepke to their C certificates. The Lepkes were retired in the 1960s, after ten years of use. [1] [2]

Aircraft on display

Lepke HA 1039 Petofi Csarnok, Repulestorteneti kiallitas, Rubik R-16b Lepke.jpg
Lepke HA 1039

Specifications (R-16b Lepke)

Data from Gabor, F [1]

General characteristics

Performance

Related Research Articles

Janka-Rotter Vándor

The Vándor (Wanderer) was a 1930s Hungarian single seat glider intended to ready students who had qualified on primary gliders for contemporary soaring and aerobatic aircraft. Only one was built.

Gyöngyös 33 Hungarian glider

The Gyöngyös 33 was the first sailplane designed in Hungary, making its first flight in June 1933. It set several national records, using ridge lift rather than thermal soaring.

The MSrE M-20 was an Hungarian primary glider with a better performance than the first generation of such aircraft. One of its designers was Ernő Rubik and the MSrE M-20 was his first major contribution. Only one was built.

Rubik R-03 Szittya I

The Rubik R-03 Szittya I was a Hungarian single-seat sailplane flown in the late 1930s. The design was developed through three improving variants. though only one of each was built.

The Jancsó-Szokolay M22 was a Hungarian single-seat sailplane first flown in 1937. Twenty were built and the type set several national records. Some remained in service up to about 1953.

Rubik R-07 Vöcsök

The Rubik R-07a Tücsök {Cicada) and R-07b Vöcsök (Grebe) were two versions of a Hungarian primary trainer, differing most obviously in the pilot's seating. First flown in the late 1930s, about 530 were built, some remaining in service into the 1960s.

Rubik R-08 Pilis

The Rubik R-08 Pilis was a Hungarian single-seat, advanced training glider first flown in 1939. It was very successful; 269 were built in batches, the first starting in 1939 and the last in 1956.

Rubik R-11b Cimbora

The Rubik R-11b Cimbora (Pal) was a Hungarian two seat glider, first flown in 1940 and intended to introduce B-certificated pilots to aero-towing techniques. It proved popular and was also used to train pilots in ridge lift flying and set several national duration records.

The Lampisch LS-16 was a Hungarian training glider of mixed construction. It was flown but not granted a Certificate of Airworthiness.

Rubik R-12 Kevély

The Rubik R-12 Kevély (Proud) was a Hungarian advanced training glider. It was designed to provide safe cloud-flying experience and also raised the Hungarian height gained record several times. About fifty were built and operated between 1941 and 1951.

Rubik R-15 Koma

The Rubik R-15 Koma (Godfather) was a side-by-side seat Hungarian training glider designed to introduce pilots to winch-launching techniques. A second, very similar but single seat design, the Rubik R-16 Lepke, provided follow-up solo experience of the same techniques. Pairs were widely used by Hungarian glider clubs post-war, with 65 of each produced.

The Rubik R-17 Móka (Joy) was a Hungarian aerobatic glider designed in the late 1930s. One prototype was built and first flown in 1944 but was destroyed near the end of World War II. Two more, with modified ailerons and a new fuselage, were built in 1950 but were abandoned after a fatal accident.

Rubik R-22 Futár

The 1943 Hungarian Rubik R-22 Futár (Courier) family of single seat, high performance sailplanes was developed between 1943 and 1958, though production did not begin until 1948. Four variants were serially produced, with the R-22S Június 18 the most numerous. There were several improvements within the types and there were three one-offs. Overall, 104 were built. They set numerous national records and one finished runner-up for distance at the 1958 VIIth World Gliding Championships, coming 11th overall.

Kemény K-02

The Kemény K-02 Szellő was a Hungarian training glider from the late 1940s. It was originally designed for a national contest to build a primary trainer but when this was won by the Rubik R-16 Lepke it was resigned to have more advanced soaring capability which could take pilots to their Silver C badge. Ninety were produced.

MSrE M-30 Fergeteg

The MSrE M-30 Fergeteg (Storm) was a Hungarian two seat advanced training glider. Originally designed in the early 1940s, its first flight was not made until 1950. Though five variants were developed, only six M-30s were built.

The MSRz Bene was a Hungarian two seat primary glider, first flown in 1952. By this time its competitor had been awarded a serial production order, so only one Bene was completed.

Rubik R-23 Gébics

The Rubik R-23 Gébics (Shrike) was a Hungarian advanced training glider, the first of a series of metal-framed gliders designed by Ernő Rubik, though only one Gébics was built.

PGE E-31 Esztergom Glider

The E-31 Esztergom was the standard single-seat training glider used in Hungary from about 1967 into the 1980s. Fifty were produced.

The Rubik R-27 Kópé (Imp), a single-seat trainer, was one of three similar, metal-framed Hungarian gliders. Two prototypes were flown in the early 1960s but the type did not reach production.

Rubik R-31 Dupla

The Rubik R-31 Dupla (Double) was a Hungarian side-by-side seat training glider first flown in 1983. Disappointing performance and vibration problems prevented it going into production.

References

  1. 1 2 3 4 5 Fekes Gabor. "R-16b Lepke, Hungarian gliders 1933-2000" . Retrieved 8 March 2019.
  2. 1 2 3 Gabor, Jareb (1988). Magyar vitorlázó repülögépek (in Hungarian). Budapest: Müszaki Könuvkiadó. pp. 119–121.
  3. ↑ Ogden, Bob (2009). Aviation Museums and Collections of Mainland Europe. Air Britain (Historians) Ltd. p. 295. ISBN   978 0 85130 418 2.Cite has empty unknown parameter: |coauthors= (help)
This page is based on this Wikipedia article
Text is available under the CC BY-SA 4.0 license; additional terms may apply.
Images, videos and audio are available under their respective licenses.