Rubik R-15 Koma

Last updated
R-15b Koma
Felszall egy Rubik R-15 Koma vitorlazo repulogep, hatterben a Csucshegy. Fortepan 29729.jpg
Koma winch-launch.
RoleSide-by-side seat training glider
National origin Hungary
ManufacturerSportárutermelő Vállalat, Esztergom.
Designer Ernő Rubik
First flightApril 1949
Number built68

The Rubik R-15 Koma (Godfather) was a side-by-side seat Hungarian training glider designed to introduce pilots to winch-launching techniques. A second, very similar but single seat design, the Rubik R-16 Lepke, provided follow-up solo experience of the same techniques. Pairs were widely used by Hungarian glider clubs post-war, with 65 of each produced.

Contents

Design and development

In 1940 Ernő Rubik began to consider a glider flight training programme based on a pair of aircraft with similar flight characteristics and sharing many components but differing in their seating. Students would begin on the R-15 Koma, with side-by-side seating and the reassurance and guidance of a tutor watching, then go solo on the R-16 Lepke. During the war, the Hungarian National Aviation Association (Országos Magyar Repülö Egyesület or OMRE) chose to use his R-11 Cimbora and the Koma and Lepke designs were shelved until, in 1948, OMRE announced a competition for single seat and two seat trainers. By the end of the year Rubik's two designs had been chosen. The prototype Koma first flew in April 1949, followed by the Lepke in the summer. [1]

The Koma was a pod-and-boom glider with a cantilever, mid-mounted wing which was rectangular in plan out to rounded tips and had 3° of dihedral. The wing was built around a single, wooden spar with wooden ribs; ply covering ahead of the spar formed a torsion-resistant D-box. The rest of the wing was fabric-covered. Diagonal drag struts near the root were made from steel tubes. Constant chord flaps and Handley Page slotted ailerons together filled the whole trailing edge, mounted on a light-metal tube false spar and fabric-covered. Flap settings were 5° for launching and 60° for landing. The wings could be folded back alongside the fuselage for transport. [1] [2]

The forward pod was built around two plywood, semi-circular, transverse frames mounted parallel to each other under the wing on a box-section beam which projected forward to the nose. This carried the two side-by-side seats, provided with dual controls, in an enclosed cockpit under a generously glazed, centrally hinged two-part canopy. It also mounted, on its underside, a semi-recessed monowheel, placed under the trailing edge on production aircraft (it was further forward on the prototype) with a short, rubber sprung landing skid ahead of it. From the aft of the beam a metal tube strut reached upwards and rearwards to support the boom that formed the rear fuselage. This tube was enclosed within the pod, which had ply-covered lower surfaces but was fabric-covered above. The upward sloping tailboom was a rectangular section, wooden, ply-covered structure mounted on the centre of the rear semi-circular frame, braced with wires from the inner wings as well as the metal tube from the lower fuselage. All Komas had a conventional tail and the production R-15b had a large, blunted triangular fin and rounded under-fin incorporating a small tailskid and carrying a roughly triangular, deep rudder. Its strut-braced tailplane was rectangular in plan with rounded tips and carried rounded elevators, centrally cut-away for rudder movement. [1] [2]

The prototype R-15 Koma first flew in April 1949. Flight trials revealed lateral instability when towed and so the single R-15a had a lengthened fuselage with a fin with its area increased by sweeping its previously upright leading edge forward, introducing the underfin and lowering the tailplane to the top of the fuselage. Its trials showed average students needed landing speeds reduced and so flaps were added to the R-15b Koma, first flown in June 1950, which went into series production. Sixty-five were built between 1950-1, becoming the standard Hungarian, dual control, winch-launch trainer. It remained in operation well into the 1960s. [1]

In 1957 Sportárutermelő Vállalat designers József Mihály, Lajos Bánvölgyi, Lajos Bende and Ferenc Major developed a light metal version of the Koma, the R-15F Fém-Koma (Metal-Koma), which flew in June 1958. The R-15F was very similar to the R-15b externally but there were some differences. The latter's rounded tips had been squared off, reducing the span by 650 mm (25.6 in) and it was 1,000 mm (39 in) longer. The cockpit canopy opened forward on a transverse hinge. The horizontal tail was also squared off and the fin had a narrow, rectangular profile. The R-15F was also about 11% heavier. Performances were close though the metal version had a higher VNE and a slightly better glide ratio at a higher speed. [2] [3]

By June 1964 the sole Fém-Koma had made 6275 launches and flown for 520 hours. [1]

Variants

R-15 Koma
Prototype. One only
R-15a Koma
Larger rudder for aerotowing. One only.
R-15b Koma
Production model with landing flaps and further tail revisions.
R-15F Fém-Koma
All-metal variant. One only.

Aircraft on display

R-15b Koma in the Hungarian Technical and Transportation Museum Petofi Csarnok, Repulestorteneti kiallitas, Rubik R-15b Koma.JPG
R-15b Koma in the Hungarian Technical and Transportation Museum

Specifications (R-15b)

Data from Gabor,F [1]

General characteristics

Performance

Related Research Articles

The Corcoran 65-1 was a motor glider of very unusual configuration, a twin engine biplane. It was designed and built in the United States in the 1960s; only two were completed.

The MSrE M-20 was a Hungarian primary glider with a better performance than the first generation of such aircraft. One of its designers was Ernő Rubik and the MSrE M-20 was his first major contribution. Only one was built.

Rubik R-03 Szittya I

The Rubik R-03 Szittya I was a Hungarian single-seat sailplane flown in the late 1930s. The design was developed through three improving variants. though only one of each was built.

The Jancsó-Szokolay M22 was a Hungarian single-seat sailplane first flown in 1937. Twenty were built and the type set several national records. Some remained in service up to about 1953.

Rubik R-07 Vöcsök

The Rubik R-07a Tücsök (Cicada) and R-07b Vöcsök (Grebe) were two versions of a Hungarian primary trainer, differing most obviously in the pilot's seating. First flown in the late 1930s, about 530 were built, some remaining in service into the 1960s.

Rubik R-08 Pilis Glider

The Rubik R-08 Pilis was a Hungarian single-seat, advanced training glider first flown in 1939. It was very successful; 269 were built in batches, the first starting in 1939 and the last in 1956.

Rubik R-11b Cimbora

The Rubik R-11b Cimbora (Pal) was a Hungarian two seat glider, first flown in 1940 and intended to introduce B-certificated pilots to aero-towing techniques. It proved popular and was also used to train pilots in ridge lift flying and set several national duration records.

Rubik R-12 Kevély

The Rubik R-12 Kevély (Proud) was a Hungarian advanced training glider. It was designed to provide safe cloud-flying experience and also raised the Hungarian height gained record several times. About fifty were built and operated between 1941 and 1951.

Rubik R-16 Lepke

The Rubik R-16 Lepke (Butterfly) was a single seat Hungarian training glider designed to follow the very similar but two seat Rubik R-15 Koma in a winch-launch training programme. The Lepke provided solo experience of the techniques learned with an instructor in an aircraft with similar handling characteristics. That done, the Lepke could be used as a standard trainer to take its pilot to C-certificate level. The pair were widely used by Hungarian glider clubs post-war, with sixty-five of each produced.

The Rubik R-17 Móka (Joy) was a Hungarian aerobatic glider designed in the late 1930s. One prototype was built and first flown in 1944 but was destroyed near the end of World War II. Two more, with modified ailerons and a new fuselage, were built in 1950 but were abandoned after a fatal accident.

Rubik R-22 Futár

The 1943 Hungarian Rubik R-22 Futár (Courier) family of single seat, high performance sailplanes was developed between 1943 and 1958, though production did not begin until 1948. Four variants were serially produced, with the R-22S Június 18 the most numerous. There were several improvements within the types and there were three one-offs. Overall, 104 were built. They set numerous national records and one finished runner-up for distance at the 1958 VIIth World Gliding Championships, coming 11th overall.

Kemény K-02

The Kemény K-02 Szellő was a Hungarian training glider from the late 1940s. It was originally designed for a national contest to build a primary trainer but when this was won by the Rubik R-16 Lepke it was resigned to have more advanced soaring capability which could take pilots to their Silver C badge. Ninety were produced.

MSrE M-30 Fergeteg

The MSrE M-30 Fergeteg (Storm) was a Hungarian two seat advanced training glider. Originally designed in the early 1940s, its first flight was not made until 1950. Though five variants were developed, only six M-30s were built.

The MSRz Bene was a Hungarian two seat primary glider, first flown in 1952. By this time its competitor had been awarded a serial production order, so only one working Bene was ever completed.

MRSz Z-03 Ifjúság

The MRSz Z-03A Ifjúság (Youth) was a Hungarian advanced training glider built in the 1950s, capable of both aerobatic and, with the revised Z-03B, blind flying instruction. They were removed from service in 1960 after fatigue analysis revealed that the fuselage structure at the wing attachment point had only a short life.

Rubik R-23 Gébics

The Rubik R-23 Gébics (Shrike) was a Hungarian advanced training glider, the first of a series of metal-framed gliders designed by Ernő Rubik, though only one Gébics was built.

PGE E-31 Esztergom

The E-31 Esztergom was the standard single-seat training glider used in Hungary from about 1967 into the 1980s. Fifty were produced.

The Rubik R-27 Kópé (Imp), a single-seat trainer, was one of three similar, metal-framed Hungarian gliders. Two prototypes were flown in the early 1960s but the type did not reach production.

Rubik R-31 Dupla

The Rubik R-31 Dupla (Double) was a Hungarian side-by-side seat training glider first flown in 1983. Disappointing performance and vibration problems prevented it going into production.

The PGE EV.1K Fecske (Swallow) was a high performance Hungarian sailplane designed and flown in the late 1960s. The sole example was destroyed in a fatal crash in 1970.

References

  1. 1 2 3 4 5 6 Fekes Gabor. "R-15b Koma, Hungarian gliders 1933-2000" . Retrieved 8 March 2019.
  2. 1 2 3 Gabor, Jareb (1988). Magyar vitorlázó repülögépek (in Hungarian). Budapest: Müszaki Könuvkiadó. pp. 111–119.
  3. ↑ Fekes Gabor. "R-15F Fém-Koma, Hungarian gliders 1933-2000" . Retrieved 8 March 2019.
  4. 1 2 Ogden, Bob (2009). Aviation Museums and Collections of Mainland Europe. Air Britain (Historians) Ltd. p. 296. ISBN   978-0-85130-418-2.
This page is based on this Wikipedia article
Text is available under the CC BY-SA 4.0 license; additional terms may apply.
Images, videos and audio are available under their respective licenses.