Sex bolt

Last updated
Sleeve nuts, one with mating bolt Sleeve nuts.jpg
Sleeve nuts, one with mating bolt

A sex bolt is a type of fastener comprising a mated pair of screw and post, which are a machine screw and a nut that is barrel-shaped. The nut has a flange and a protruding boss that is internally threaded. The bolt (mated pair, screw and post) sits within the components being fastened, and the flange provides the bearing surface.

A sex bolt is normally chosen because of the low profile of its nut compared with that of other nuts. The sex bolt often has a built-in feature, such as a slot, to aid in tightening the fastener. Some sex bolts, more commonly known as "architectural bolts", have knurled barrels to allow one-sided assembly.

The sex bolt consists of a female (internally) threaded barrel (nut) and a male (externally) threaded screw. Both the barrel and screw have heads designed to clamp (bind) material between the head of the barrel and the head of the screw, or to bridge the gap between two parts.

Other names for sex bolts, or (in some cases) for the female half specifically, include:

Applications vary widely from book binding to installing bathroom partitions. This group of fasteners are used to assemble fitness apparatus, solar panels, playground equipment, railing systems, furniture, athletic helmets, knives, store fixtures, signs, panic bars, and many other products.

Technical guide to mating fasteners:[ citation needed ]

Barrel diameter
mating fasteners often are going through pre-drilled holes. The barrel diameter should be slightly less than the installation hole.
Barrel length
the barrel length is measured from underneath the head to the end of the barrel. Normally the length of the barrel is shorter than the thickness of the material being clamped. Another common term is "grip length", which is the thickness of the material that a mating bolt can effectively fasten or clamp.
Thread size
length and thread class fit for both barrel and screw. The more thread depth, the more difficult these parts are to manufacture, and the more expensive.
Head style
the most common head style for a mating fastener is a "truss" head. Other head styles are button, flat, grommet, hex head, large truss, low profile, oval, rivet and T-head.
Drive systems
mating fasteners are available in a variety of drives such as slotted, socket, Phillips, combination Phillips/slotted, as well as tamper-resistant drives: one way, 6-lobe with pin and drilled spanner.
Material and finish
mating fasteners are available in aluminium, steel, brass, copper, stainless steel and plastic materials. Barrels and screws are available anodized, zinc-plated, brass-plated, chrome-plated, bronze-plated, nickel-plated and black-oxide finish.

Related Research Articles

<span class="mw-page-title-main">Fastener</span> Hardware device that mechanically joins or affixes two or more objects together

A fastener or fastening is a hardware device that mechanically joins or affixes two or more objects together. In general, fasteners are used to create non-permanent joints; that is, joints that can be removed or dismantled without damaging the joining components. Steel fasteners are usually made of stainless steel, carbon steel, or alloy steel.

<span class="mw-page-title-main">Bolted joint</span> Mechanical joint secured by a threaded fastener

A bolted joint is one of the most common elements in construction and machine design. It consists of a male threaded fastener that captures and joins other parts, secured with a matching female screw thread. There are two main types of bolted joint designs: tension joints and shear joints.

<span class="mw-page-title-main">Lathe faceplate</span> Workholding accessory

A lathe faceplate is a basic workholding accessory for a wood or metal turning lathe. It is a circular metal plate which fixes to the end of the lathe spindle. The workpiece is then clamped to the faceplate, typically using t-slot nuts in slots in the faceplate, or less commonly threaded holes in the faceplate itself.

The ISO metric screw thread is the most commonly used type of general-purpose screw thread worldwide. They were one of the first international standards agreed when the International Organization for Standardization (ISO) was set up in 1947.

<span class="mw-page-title-main">Piping and plumbing fitting</span> Connecting pieces in pipe systems

A fitting or adapter is used in pipe systems to connect sections of pipe or tube, adapt to different sizes or shapes, and for other purposes such as regulating fluid flow. These fittings are used in plumbing to manipulate the conveyance of fluids such as water for potatory, irrigational, sanitary, and refrigerative purposes, gas, petroleum, liquid waste, or any other liquid or gaseous substances required in domestic or commercial environments, within a system of pipes or tubes, connected by various methods, as dictated by the material of which these are made, the material being conveyed, and the particular environmental context in which they will be used, such as soldering, mortaring, caulking, Plastic welding, welding, friction fittings, threaded fittings, and compression fittings.

<span class="mw-page-title-main">Locknut</span> Threaded fastener

A locknut, also known as a lock nut, locking nut, self-locking nut, prevailing torque nut, stiff nut or elastic stop nut, is a nut that resists loosening under vibrations and torque. Prevailing torque nuts have some portion of the nut that deforms elastically to provide a locking action. Free-spinning locknuts exist which carry the advantage of not requiring extra torque until seated.

<span class="mw-page-title-main">Anchor bolt</span> Connection elements that transfer loads and shear forces to concrete.

Anchor bolts are used to connect structural and non-structural elements to concrete. The connection can be made by a variety of different components: anchor bolts, steel plates, or stiffeners. Anchor bolts transfer different types of load: tension forces and shear forces.

<span class="mw-page-title-main">T-nut</span>

A T-nut, T nut, or tee nut is a type of nut used to fasten a wood, particle or composite materials workpiece, leaving a flush surface.

<span class="mw-page-title-main">Well nut</span>

A well nut is a blind rivet-like type of fastener used to blindly fasten a piece and to seal the bolt hole.

<span class="mw-page-title-main">Wingnut (hardware)</span>

A wingnut, wing nut or butterfly nut is a type of nut with two large metal "wings", one on each side, so it can be easily tightened and loosened by hand without tools.

Multi-jackbolt tensioners (MJT) are an alternative to traditional bolted joints. Rather than needing to tighten one large bolt, MJTs use several smaller jackbolts to significantly reduce the torque required to attain a certain preload. MJTs range in thread sizes from 3⁄4 in (19 mm) to 32 in (810 mm) and can achieve 20 million pounds-force or more. MJTs only require hand-held tools, such as torque wrenches or air/electric impacts, for loading and unloading bolted joints.

<span class="mw-page-title-main">Barrel nut</span>

A barrel nut is a specialized forged nut, and is commonly used in aerospace and ready-to-assemble furniture applications.

<span class="mw-page-title-main">Screw</span> Type of fastener characterized by a thread wrapped around a cylinder core

A screw is an externally helical threaded fastener capable of being tightened or released by a twisting force (torque) to the head. The most common uses of screws are to hold objects together and there are many forms for a variety of materials. Screws might be inserted into holes in assembled parts or a screw may form its own thread.

<span class="mw-page-title-main">Nut (hardware)</span> Type of fastener with a threaded hole

A nut is a type of fastener with a threaded hole. Nuts are almost always used in conjunction with a mating bolt to fasten multiple parts together. The two partners are kept together by a combination of their threads' friction, a slight stretching of the bolt, and compression of the parts to be held together.

<span class="mw-page-title-main">Differential screw</span>

A differential screw is a mechanism used for making small, precise adjustments to the spacing between two objects. A differential screw uses a spindle with two screw threads of differing leads, and possibly opposite handedness, on which two nuts move. As the spindle rotates, the space between the nuts changes based on the difference between the threads. These mechanisms allow extremely small adjustments using commonly available screws. A differential screw mechanism using two nuts incurs higher friction and therefore requires more torque to turn than a simple, single lead screw with an equivalent pitch.

ISO 898 is an international standard that defines mechanical and physical properties for metric fasteners. This standard is the origin for other standards that define properties for similar metric fasteners, such as SAE J1199 and ASTM F568M. It is divided into five (nonconsecutive) parts:

<span class="mw-page-title-main">Bolt (fastener)</span> Threaded fastener with an external male thread requiring a matching female thread

A bolt is an externally helical threaded fastener capable of being tightened or released by a twisting force (torque) to a matching nut. The bolt has an external male thread requiring a matching nut with a pre-formed female thread.

<span class="mw-page-title-main">Wrench size</span>

Width across flats is the distance between two parallel surfaces on the head of a screw or bolt, or a nut, mostly for torque transmission by positive locking.

<span class="mw-page-title-main">Furniture screws</span> Screws used on furniture, including specialty screws used on ready-to-assemble furniture

A furniture screw can refer to any type of screw used on furniture. Different types of screws have different uses in furniture.

References

  1. ↑ "Architectural Sex Bolts". Fastenright Ltd. Retrieved 2023-06-06.
  2. 1 2 3 "Barrel Nuts". Accu Limited. Retrieved 6 June 2023.
  3. ↑ "Binding Barrels and Screws". Catalog. McMaster-Carr. Retrieved 29 April 2020.
  4. ↑ "Book Screws - Female | Components Direct". www.components-direct.com. Retrieved 2023-06-06.
  5. ↑ "Metal Binding Screws | Binding Screws | Book Screw | Binder Screws | Brass Binding Screws | Essentra Components UK". www.essentracomponents.com. Retrieved 2023-06-06.
  6. ↑ "Brass Chicago Binding Screws | Made in the USA". USBind.com. Retrieved 2023-06-06.
  7. ↑ Sex bolts & mating fasteners, 2014, retrieved 2014-10-06
  8. ↑ "catalog page (Sex Bolts)". Bolt Depot. Retrieved 2013-03-21. Typical catalogue page.
  9. ↑ "Brass Screw & Post - 13mm". Shepherds London. Retrieved 2023-06-06.
  10. ↑ "Socket Countersunk Sleeve Nuts". www.pts-uk.com. Retrieved 2023-06-06.
This page is based on this Wikipedia article
Text is available under the CC BY-SA 4.0 license; additional terms may apply.
Images, videos and audio are available under their respective licenses.