 | This article includes a list of general references, but it lacks sufficient corresponding inline citations .(May 2011) |
The Simpson planetary gearset is a compound planetary gear train consisting of two planetary gearsets sharing a common sun gear. A Simpson gearset delivers three forward gears and one reverse, plus neutral, and is commonly employed in three and four ratio automatic transmissions. [1] It is one of the several designs invented by American engineer Howard Simpson.
The two planetaries are interdependent via two permanent connections, that commonly but not necessarily have the same gears and gear ratios, both gearsets share a common sun gear. The planet carrier of the first gearset ("first" means closer to the input shaft) is in synchrony with the second gearset's ring. Owing to these linkages, only two bands and two clutches are needed to command the gearsets. [2]
| First Gearset | Second Gearset | |||||
|---|---|---|---|---|---|---|
| Sun | Carrier | Ring | Sun | Carrier | Ring | |
| Low | -receive | output | input | -send | braked | |
| Reduced | braked | output | input | |||
| Direct | input | output | input | |||
| Reverse | input | braked | output | |||
In the first gear, the first gearset actuates on the second gearset and output shaft; the second gearset reacts and makes the sun turn in reverse, causing the first gearset to increase the reduction ratio. In first gear, the input is locked to the first ring. The first carrier is locked to the output and second ring. The second carrier is locked so its ring motion causes the common sun to spin retrograde. The retrograde spin reduces the first carriers reaction to its ring motion thereby doubling the reduction of the first set and output. [3]
Command of second gear is simpler, the second carrier is released and the sun drive is braked. Thus input is locked to the first ring, and output is locked to the first carrier.
The third gear is always direct drive (1:1), by feeding input to both the sun drive and the first ring, both carriers are effectively locked, so input directly drives the output.
One problem of changing from first to second gear is that two bands must actuate in synchrony: the planet carrier of the second gearset must release at the same time as the sun band is actuated. Sprag clutches mitigate roughness when a shift requires a combination of bands to be released or actuated.
GM's Turbo Hydra-Matic 350 and 400 transmissions utilized overrunning clutches in both the low and intermediate gears, allowing for fully progressive shifting with no "overlap". Gear changing patterns in some Simpson gearboxes, including modern 4-speed units, avoid first gear as much as they can, going up to 2nd as soon as possible, and avoiding reducing to 1st unless absolutely necessary (very slow speed plus floored throttle).
In the 1990s and 2000s, the Simpson gearset went out of fashion and was replaced by more complex transmissions. A Ravigneaux planetary gearset was combined with a simple planetary gearset to form a Lepelletier gearset, that offers six useful forward gears.
Even the latest 4-speed transmissions are not Simpson; they have only two planetary sets, while a Simpson transmission needs three planetary sets to get four speeds, the third planetary being an integrated overdrive.
Nevertheless, it is still possible to find new automatic transmissions based on the Simpson gearset. Such transmissions are three- or four-speed, and are often electronically controlled versions of older projects. They are kept in production because they are cheap, reliable, well-known and good enough for the target application.
A clutch is a mechanical device that engages and disengages power transmission, especially from a drive shaft to a driven shaft. In the simplest application, clutches connect and disconnect two rotating shafts. In these devices, one shaft is typically attached to an engine or other power unit, while the other shaft provides output power for work. Typically the motions involved are rotary, but linear clutches also exist.
A differential is a gear train with three drive shafts that has the property that the rotational speed of one shaft is the average of the speeds of the others, or a fixed multiple of that average.
An automatic transmission is a multi-speed transmission used in internal combustion engine-based motor vehicles that does not require any input from the driver to change forward gears under normal driving conditions. It typically includes a transmission, axle, and differential in one integrated assembly, thus technically becoming a transaxle.
An epicyclic gear train consists of two gears mounted so that the center of one gear revolves around the center of the other. A carrier connects the centers of the two gears and rotates the planet and sun gears mesh so that their pitch circles roll without slip. A point on the pitch circle of the planet gear traces an epicycloid curve. In this simplified case, the sun gear is fixed and the planetary gear(s) roll around the sun gear.
Overdrive is the operation of an automobile cruising at sustained speed with reduced engine revolutions per minute (RPM), leading to better fuel consumption, lower noise, and lower wear. The term is ambiguous. The most fundamental meaning is that of an overall gear ratio between engine and wheels, such that the car is over-geared, and cannot reach its potential top speed, i.e. the car could travel faster if it were in a lower gear, with the engine turning at higher RPM.
Propulsion transmission is the mode of transmitting and controlling propulsion power of a machine. The term transmission properly refers to the whole drivetrain, including clutch, gearbox, prop shaft, differential, and final drive shafts. In the United States the term is sometimes used in casual speech to refer more specifically to the gearbox alone, and detailed usage differs. The transmission reduces the higher engine speed to the slower wheel speed, increasing torque in the process. Transmissions are also used on pedal bicycles, fixed machines, and where different rotational speeds and torques are adapted.
A continuously variable transmission (CVT) is an automatic transmission that can change seamlessly through a continuous range of gear ratios. This contrasts with other transmissions that provide a limited number of gear ratios in fixed steps. The flexibility of a CVT with suitable control may allow the engine to operate at a constant RPM while the vehicle moves at varying speeds.
A manual transmission (MT), also known as manual gearbox, standard transmission, or stick shift, is a multi-speed motor vehicle transmission system, where gear changes require the driver to manually select the gears by operating a gear stick and clutch.
Global Hybrid Cooperation, formerly Advanced Hybrid System 2 (AHS2), is a set of hybrid vehicle technologies jointly developed by General Motors, Daimler, and Chrysler LLC, with BMW joining in 2005. It uses 2 or 3 planetary gearsets in an automatic transmission: one on the internal combustion engine (ICE) side paired with a second, forming the compound split, and possibly one third additional planetary gearset to multiply the number of fixed gear ratios. General Motors has stopped using the "AHS2" name as of 2006, preferring to call it simply a two-mode hybrid system.
Hydramatic is an automatic transmission developed by both General Motors' Cadillac and Oldsmobile divisions. Introduced in 1939 for the 1940 model year vehicles, the Hydramatic was the first mass-produced fully-automatic transmission developed for passenger automobile use.
TorqueFlite is the trademarked name of Chrysler Corporation's automatic transmissions, starting with the three-speed unit introduced late in the 1956 model year as a successor to Chrysler's two-speed PowerFlite. In the 1990s, the TorqueFlite name was dropped in favor of alphanumeric designations, although the latest Chrysler eight-speed automatic transmission has revived the name.
A sprag clutch is a one-way freewheel clutch. It resembles a roller bearing but, instead of cylindrical rollers, non-revolving asymmetric figure-eight shaped sprags, or other elements allowing single direction rotation, are used. When the unit rotates in one direction the rollers slip or free-wheel, but when a torque is applied in the opposite direction, the sprags tilt slightly, producing a wedging action and binding because of friction.
7G-Tronic is Mercedes-Benz's trademark name for its seven-speed automatic transmission, starting off with the W7A 700 and W7A 400 as core models.
The Rohloff Speedhub is an epicyclic internal hub gear for bicycles, developed and patented by Rohloff AG. It has been manufactured and marketed by that company since 1998. The Speedhub 500/14 has 14 equally spaced, sequential, non-overlapping gear ratios operated by a single twistgrip. The overall gear range is 526%, meaning the highest gear is 5.26 times as high as the lowest gear. Individual gear shifts when shifting up give an increase of about 13.6%.
A torque limiter is an automatic device that protects mechanical equipment, or its work, from damage by mechanical overload. A torque limiter may limit the torque by slipping, or uncouple the load entirely. The action of a torque limiter is especially useful to limit any damage due to crash stops and jams.
A transmission control unit (TCU), also known as a transmission control module (TCM), or a gearbox control unit (GCU), is a type of automotive ECU that is used to control electronic automatic transmissions. Similar systems are used in conjunction with various semi-automatic transmissions, purely for clutch automation and actuation. A TCU in a modern automatic transmission generally uses sensors from the vehicle, as well as data provided by the engine control unit (ECU), to calculate how and when to change gears in the vehicle for optimum performance, fuel economy and shift quality.
The Ravigneaux gearset is a double planetary gear set, invented by Pol Ravigneaux, who filed a patent application on July 28, 1949, in Neuilly-sur-Seine France. This planetary gear set, commonly used in automatic transmissions, is constructed from two gear pairs, ring–planet and planet–planet.
The GM MR6/F40 six-speed manual transaxle was first developed for GM Europe by Saab Powertrain, for use in Saab and Opel applications. Originally a design developed by GM Powertrain Sweden Södertälje - Europe six-speed manual transaxle was originally built by Saab in its transmission plant in Gothenburg, Sweden (2002-2003) but production was moved to Opel in Rüsselsheim am Main, Germany since 2004. Its first use in Europe was the new Saab 9-3 2003-2011, while first use in North America was the same, in the Aero model. It is also used in 9-5 2010-2012 models.
9HP is ZF Friedrichshafen AG's trademark name for its nine-speed automatic transmission models for transverse engine applications, designed by ZF's subsidiary in Saarbrücken and built in Gray Court, South Carolina. It is used in front-wheel drive and all-wheel drive vehicles.
9G-Tronic is Mercedes-Benz's trademark name for its nine-speed automatic transmission, starting off with the W9A 700 as core model.