Synthesis of hexagonal boron nitride

Last updated

Two dimensional hexagonal boron nitride (2D h-BN) is a material of comparable structure to graphene with potential applications in e.g. photonics., [1] fuel cells [2] and as a substrate for two-dimensional heterostructures. [3] 2D h-BN is isostructural to graphene, but where graphene is conductive, 2D h-BN is a wide-gap insulator. [3]

Contents

The properties of 2D h-BN films depends greatly on the quality of the films. It has been challenging to synthesize high-quality 2D h-BN over large areas. [3] In particular, the small grain size of polycrystalline h-BN results in many grain boundaries, which create charge traps and higher surface roughness.

The production of 2D h-BN can be divided into top-down and bottom-up approaches. In bottom-up methods, a film is grown or deposited on a surface; in top-down methods, a larger structure is reduced until the desired state or structure is achieved.

Top-down methods

The general idea behind top-down approaches is to take bulk h-BN, break the Van der Waals forces between the hexagonal layers and separate the resulting two-dimensional sheets of h-BN. These techniques mainly consist of mechanical and chemical exfoliation methods. [3]

In mechanical exfoliation the atomic sheets of h-BN are physically pulled or separated from each other. For example using regular adhesive tape to peel off graphene sheets is one of the most famous mechanical exfoliation methods [4] and similar techniques can also be used to create h-BN sheets. [5] Generally speaking mechanical exfoliation methods can be considered as simple ways to fabricate h-BN nanosheets, but their yield can be small [6] and the size of the fabricated structures is usually limited. [3] On the other hand, the number of defects on the produced nanosheets has been found to be smaller compared to chemical methods. [7]

Chemical exfoliation is carried out in liquid solvents such as dichloroethane [8] and dimethylformamide. [9] Sonication is used to break Van der Waals forces in h-BN crystals which allows the solvent molecules to expand the atomic layers. [7] These methods are quite simple and can also provide a higher yield compared to mechanical exfoliation, although the samples are easily contaminated. [6]

Bottom-up methods

Chemical vapor deposition

Chemical vapor deposition (CVD) is a bottom-up chemical deposition method used to construct high-quality nanoscale films. In CVD, a substrate is exposed to precursors, which react on the wafer surface to produce the desired film. This reaction often also results in toxic byproducts. Historically, ultra-high vacuum CVD (UHVCVD) has been used for thin h-BN deposition on transition metals. [10] More recently, CVD of h-BN has also been successful on metallic surfaces at higher pressures. [11]

CVD is reliant on the use of reactive precursors. For h-BN, there are gaseous, liquid, and solid options to choose from, each with their respective advantages and drawbacks. Gaseous precursors, such as BF3/NH3, BCl3/NH3, and B2H6/NH3, are toxic and require careful ratios of gases to preserve a 1:1 B/N stoichiometry. [12] Liquid precursors, such as borazine, have equal amounts of boron and nitrogen, and do not produce highly toxic side products. However, they are sensitive to moisture, and hydrolyze readily. [13] This drawback can be counteracted by raising the temperature, but higher temperatures also result in increased rates of reaction. Finally, for solid precursors, borazane is stable and has a 1:1 B/N stoichiometry. Its drawback is its decomposition into the highly active BH2NH2, which polymerizes at room temperature. Pure borazane consequently does not work as a precursors, and should be mixed with BH2NH2 and borazine. [7]

CVD is classified by its operation conditions into atmospheric pressure CVD (APCVD), low-pressure CVD (LPCVD) and ultra-high vacuum CVD. Higher vacuums require more sophisticated equipment, and higher operation costs, while higher pressures yield faster growth. For h-BN, APCVD has been unable to precisely control the number of layers. At least LPCVD is currently required to produce large area monolayer h-BN. [14]

The choice of substrate in CVD is important, as the film under production must stick to the surface. In h-BN, as in graphene, transition metals such as Cu or Ni are popular choices for CVD substrate materials. Platinum has also been used as a wafer, [15] as has iron foil [16] and cobalt. [17] The drawback with catalytic transition metal wafer materials is the need to transfer the end result to a target substrate, such as silicon. This procedure often damages or contaminates the film. Some h-BN films have been grown on Si, [18] SiO2/Si, [18] and sapphire [19]

The orientation of domains on the h-BN film is affected by the choice of substrate material and its orientation. Typically, domains are triangular in LPCVD, and triangular, truncated triangular, or hexagonal in APCVD. Often, these domains are randomly oriented, but h-BN domains align strictly with copper (100) or (111) surface lattices. [20] With Cu (110), alignment is less strict, but still strong over millimeter distances. [21]

Physical vapor deposition

Sputtering

In sputtering, a solid target of the desired film material is bombarded with energetic particles, so that a thin film can be produced on a wafer facing the target. Ar ion beams have been used to sputter h-BN on Cu foils, resulting in high-quality, few-layer films, [22] and magnetron sputtering of B in N2/Ar has been used to grow high-quality h-BN on Ru. [23] This process results in films two atomic layers thick; thicker films can be grown by alternating room temperature deposition and annealing cycles.

Co-segregation

When a source of boron and nitrogen, such as amorphous BN, is sandwiched between a Co or Ni film and SiO2, it is possible to grow an atomically thin h-BN film on the metal surface by annealing the heterostructure in a vacuum. The B and N atoms dissolve in the metal bulk, diffuse through the film, and precipitate on the surface. [24] In this way, the use of unconventional or toxic precursors is avoided.

Other methods

In molecular beam epitaxy (MBE) heated gaseous elements are allowed to condense on the wafer. MBE has been used to grow h-BN films from elemental B and N on Ni foils. [25]

Molten boron oxide reacts with gaseous ammonia to form an ultrathin h-BN film at the reaction interface. [26] The film grows to 20-30 nm in thickness, after which the process self-terminates, the setup is cooled down, and the boron oxide can be dissolved in water.

Related Research Articles

Boron nitride Refractory compound with formula BN

Boron nitride is a thermally and chemically resistant refractory compound of boron and nitrogen with the chemical formula BN. It exists in various crystalline forms that are isoelectronic to a similarly structured carbon lattice. The hexagonal form corresponding to graphite is the most stable and soft among BN polymorphs, and is therefore used as a lubricant and an additive to cosmetic products. The cubic variety analogous to diamond is called c-BN; it is softer than diamond, but its thermal and chemical stability is superior. The rare wurtzite BN modification is similar to lonsdaleite but slightly softer than the cubic form.

Chemical vapor deposition Method used to make thin films for semiconductors

Chemical vapor deposition (CVD) is a vacuum deposition method used to produce high quality, and high-performance, solid materials. The process is often used in the semiconductor industry to produce thin films.

Molybdenum disulfide Chemical compound

Molybdenum disulfide is an inorganic compound composed of molybdenum and sulfur. Its chemical formula is MoS
2.

A bilayer is a double layer of closely packed atoms or molecules.

Epitaxy Crystal growth process relative to the substrate

Epitaxy refers to a type of crystal growth or material deposition in which new crystalline layers are formed with one or more well-defined orientations with respect to the crystalline seed layer. The deposited crystalline film is called an epitaxial film or epitaxial layer. The relative orientation(s) of the epitaxial layer to the seed layer is defined in terms of the orientation of the crystal lattice of each material. For most epitaxial growths, the new layer is usually crystalline and each crystallographic domain of the overlayer must have a well-defined orientation relative to the substrate crystal structure. Epitaxy can involve single-crystal structures, although grain-to-grain epitaxy has been observed in granular films. For most technological applications, single domain epitaxy, which is the growth of an overlayer crystal with one well-defined orientation with respect to the substrate crystal, is preferred. Epitaxy can also play an important role while growing superlattice structures.

Graphene Hexagonal lattice made of carbon atoms

Graphene is an allotrope of carbon consisting of a single layer of atoms arranged in a two-dimensional honeycomb lattice nanostructure. The name is derived from "graphite" and the suffix -ene, reflecting the fact that the graphite allotrope of carbon contains numerous double bonds.

Borazine Chemical compound

Borazine, also known as borazole, is a polar inorganic compound with the chemical formula B3H6N3. In this cyclic compound, the three BH units and three NH units alternate. The compound is isoelectronic and isostructural with benzene. For this reason borazine is sometimes referred to as “inorganic benzene”. Like benzene, borazine is a colourless liquid with an aromatic smell.

Tungsten disulfide Chemical compound

Tungsten disulfide is an inorganic chemical compound composed of tungsten and sulfur with the chemical formula WS2. This compound is part of the group of materials called the transition metal dichalcogenides. It occurs naturally as the rare mineral tungstenite. This material is a component of certain catalysts used for hydrodesulfurization and hydrodenitrification.

Nanomesh

The nanomesh is an inorganic nanostructured two-dimensional material, similar to graphene. It was discovered in 2003 at the University of Zurich, Switzerland.

Fluorographene Chemical compound

Fluorographene (or perfluorographane, graphene fluoride) is a fluorocarbon derivative of graphene. It is a two dimensional carbon sheet of sp3 hybridized carbons, with each carbon atom bound to one fluorine. The chemical formula is (CF)n. In comparison, Teflon (polytetrafluoroethylene), -(CF2)n-, consists of carbon "chains" with each carbon bound to two fluorines.

Bilayer graphene is a material consisting of two layers of graphene. One of the first reports of bilayer graphene was in the seminal 2004 Science paper by Geim and colleagues, in which they described devices "which contained just one, two, or three atomic layers"

A nanosheet is a two-dimensional nanostructure with thickness in a scale ranging from 1 to 100 nm.

Borophene

Borophene is a crystalline atomic monolayer of boron, i.e., it is a two-dimensional allotrope of boron and also known as boron sheet. First predicted by theory in the mid-1990s, different borophene structures were experimentally confirmed in 2015.

Potential graphene applications include lightweight, thin, and flexible electric/photonics circuits, solar cells, and various medical, chemical and industrial processes enhanced or enabled by the use of new graphene materials.

Transition metal dichalcogenide monolayers

Transition-metal dichalcogenide (TMD or TMDC) monolayers are atomically thin semiconductors of the type MX2, with M a transition-metal atom (Mo, W, etc.) and X a chalcogen atom (S, Se, or Te). One layer of M atoms is sandwiched between two layers of X atoms. They are part of the large family of so-called 2D materials, named so to emphasize their extraordinary thinness. For example, a MoS2 monolayer is only 6.5 Å thick. The key feature of these materials is the interaction of large atoms in the 2D structure as compared with first-row transition-metal dichalcogenides, e.g., WTe2 exhibits anomalous giant magnetoresistance and superconductivity.

In materials science, the term single-layer materials or 2D materials refers to crystalline solids consisting of a single layer of atoms. These materials are promising for some applications but remain the focus of research. Single-layer materials derived from single elements generally carry the -ene suffix in their names, e.g. graphene. Single-layer materials that are compounds of two or more elements have -ane or -ide suffixes. 2D materials can generally be categorized as either 2D allotropes of various elements or as compounds.

A two-dimensional semiconductor is a type of natural semiconductor with thicknesses on the atomic scale. Geim and Novoselov et al. initiated the field in 2004 when they reported a new semiconducting material graphene, a flat monolayer of carbon atoms arranged in a 2D honeycomb lattice. A 2D monolayer semiconductor is significant because it exhibits stronger piezoelectric coupling than traditionally employed bulk forms. This coupling could enable applications. One research focus is on designing nanoelectronic components by the use of graphene as electrical conductor, hexagonal boron nitride as electrical insulator, and a transition metal dichalcogenide as semiconductor.

A rapidly increasing list of graphene production techniques have been developed to enable graphene's use in commercial applications.

Boron nitride nanosheet

Boron nitride nanosheet is a two-dimensional crystalline form of the hexagonal boron nitride (h-BN), which has a thickness of one to few atomic layers. It is similar in geometry to its all-carbon analog graphene, but has very different chemical and electronic properties – contrary to the black and highly conducting graphene, BN nanosheets are electrical insulators with a band gap of ~5.9 eV, and therefore appear white in color.

A graphene morphology is any of the structures related to, and formed from, single sheets of graphene. 'Graphene' is typically used to refer to the crystalline monolayer of the naturally occurring material graphite. Due to quantum confinement of electrons within the material at these low dimensions, small differences in graphene morphology can greatly impact the physical and chemical properties of these materials. Commonly studied graphene morphologies include the monolayer sheets, bilayer sheets, graphene nanoribbons and other 3D structures formed from stacking of the monolayer sheets.

References

  1. ↑ Andres Castellanos-Gomez (2016). "Why all the fuss about 2D semiconductors?". Nature Photonics. 10 (4): 202–204. arXiv: 1604.06425 . Bibcode:2016NaPho..10..202C. doi:10.1038/nphoton.2016.53. S2CID   118543165.
  2. ↑ Hu, S.; et al. (2014). "Proton transport through one-atom-thick crystals". Nature. 516 (7530): 227–230. arXiv: 1410.8724 . Bibcode:2014Natur.516..227H. doi:10.1038/nature14015. PMID   25470058. S2CID   4455321.
  3. 1 2 3 4 5 Wang, H.; et al. (2017). "Recent progress in synthesis of two-dimensional hexagonal boron nitride". Journal of Semiconductors. 38 (3): 031003. Bibcode:2017JSemi..38c1003W. doi:10.1088/1674-4926/38/3/031003.
  4. ↑ Novoselov K. S.; et al. (2004). "Electric field effect in atomically thin carbon films". Science. 306 (5696): 666–669. arXiv: cond-mat/0410550 . Bibcode:2004Sci...306..666N. doi:10.1126/science.1102896. PMID   15499015. S2CID   5729649.
  5. ↑ Novoselov K. S.; et al. (2005). "Two-dimensional atomic crystals". Proc Natl Acad Sci USA. 102 (30): 10451–10453. arXiv: cond-mat/0503533 . Bibcode:2005PNAS..10210451N. doi: 10.1073/pnas.0502848102 . PMC   1180777 . PMID   16027370.
  6. 1 2 Xu M. S.; et al. (2013). "Graphene-like two-dimensional materials". Chem. Rev. 113 (5): 3766–3798. doi:10.1021/cr300263a. PMID   23286380.
  7. 1 2 3 Bao, Jie; et al. (2016). "Synthesis and applications of two-dimensional hexagonal boron nitride in electronics manufacturing". Electronic Materials Letters. 12 (1): 1–16. Bibcode:2016EML....12....1B. doi:10.1007/s13391-015-5308-2. S2CID   135897866.
  8. ↑ Warner J. H.; et al. (2010). "Atomic resolution imaging and topography of boron nitride sheets produced by chemical exfoliation". ACS Nano. 4 (3): 1299–1304. doi:10.1021/nn901648q. PMID   20148574.
  9. ↑ Zhi C.; et al. (2009). "Large-scale fabrication of few-atomic-layer boron nitride nanosheets and their utilization in polymeric composites with improved thermal and mechanical properties". Adv. Mater. 21 (28): 2889–2893. doi:10.1002/adma.200900323.
  10. ↑ Nagashima, A.; et al. (1995). "Electronic structure of monolayer hexagonal boron nitride physisorbed on metal surfaces". Physical Review Letters. 75 (21): 3918–3921. Bibcode:1995PhRvL..75.3918N. doi:10.1103/PhysRevLett.75.3918. PMID   10059764.
  11. ↑ Kim, G.; et al. (2013). "Growth of high-crystalline, single-layer hexagonal boron nitride on recyclable platinum foil". Nano Letters. 13 (4): 1834–1839. Bibcode:2013NanoL..13.1834K. doi:10.1021/nl400559s. PMID   23527543.
  12. ↑ Pierson, Hugh O. (1975). "Boron Nitride Composites By Chemical Vapor Deposition". Journal of Composite Materials. 9 (3): 228–240. Bibcode:1975JCoMa...9..228P. doi:10.1177/002199837500900302. OSTI   4146652. S2CID   136710862.
  13. ↑ Sun, Yongzhou; et al. (2015). "Behavior of decomposed ammonia borane at high pressure". Journal of Physics and Chemistry of Solids. 84: 75–79. Bibcode:2015JPCS...84...75S. doi: 10.1016/j.jpcs.2014.12.004 .
  14. ↑ Koepke, Justic C.; et al. (2016). "Role of Pressure in the Growth of Hexagonal Boron Nitride Thin Films from Ammonia-Borane". Chemistry of Materials. 28 (2): 4169–4179. arXiv: 1605.06861 . doi:10.1021/acs.chemmater.6b00396. S2CID   49522256.
  15. ↑ Gao, Yang; et al. (2013). "Repeated and Controlled Growth of Monolayer, Bilayer and Few-Layer Hexagonal Boron Nitride on Pt Foils". ACS Nano. 7 (6): 5199–5206. doi:10.1021/nn4009356. PMID   23663007.
  16. ↑ Kim SM; et al. (2015). "Synthesis of large-area multilayer hexagonal boron nitride for high material performance". Nature Communications. 6: 8662. Bibcode:2015NatCo...6.8662K. doi:10.1038/ncomms9662. PMC   4639899 . PMID   26507400.
  17. ↑ Orofeo, Carlo M.; et al. (2013). "Growth and low-energy electron microscopy characterization of monolayer hexagonal boron nitride on epitaxial cobalt". Nano Research. 6 (5): 335–347. doi:10.1007/s12274-013-0310-1. S2CID   136687731.
  18. 1 2 Yu, Jie; et al. (2010). "Vertically Aligned Boron Nitride Nanosheets: Chemical Vapor Synthesis, Ultraviolet Light Emission, and Superhydrophobicity". ACS Nano. 4 (1): 414–422. doi:10.1021/nn901204c. PMID   20047271.
  19. ↑ Jang, A-Rang; et al. (2016). "Wafer-Scale and Wrinkle-Free Epitaxial Growth of Single-Orientated Multilayer Hexagonal Boron Nitride on Sapphire". Nano Letters. 16 (5): 3360–3366. Bibcode:2016NanoL..16.3360J. doi:10.1021/acs.nanolett.6b01051. PMID   27120101.
  20. ↑ Liu, Lei; et al. (2014). "Unusual role of epilayer–substrate interactions in determining orientational relations in van der Waals epitaxy". Proc Natl Acad Sci USA. 111 (47): 16670–16675. Bibcode:2014PNAS..11116670L. doi: 10.1073/pnas.1405613111 . PMC   4250159 . PMID   25385622.
  21. ↑ Tay, Roland Yingjie; et al. (2016). "Synthesis of aligned symmetrical multifaceted monolayer hexagonal boron nitride single crystals on resolidified copper". Nanoscale. 8 (4): 2434–2444. Bibcode:2016Nanos...8.2434T. doi:10.1039/C5NR08036C. PMID   26753762.
  22. ↑ Wang, H.; et al. (2015). "Controlled Growth of Few‐Layer Hexagonal Boron Nitride on Copper Foils Using Ion Beam Sputtering Deposition". Small. 11 (13): 1542–1547. doi:10.1002/smll.201402468. PMID   25367702.
  23. ↑ Sutter, P.; et al. (2013). "Scalable Synthesis of Uniform Few-Layer Hexagonal Boron Nitride Dielectric Films". Nano Letters. 13 (1): 276–281. Bibcode:2013NanoL..13..276S. doi:10.1021/nl304080y. PMID   23244762.
  24. ↑ Suzuki, Satoru; et al. (2012). "Growth of atomically thin hexagonal boron nitride films by diffusion through a metal film and precipitation". J. Phys. D: Appl. Phys. 45 (38): 385304. Bibcode:2012JPhD...45L5304S. doi:10.1088/0022-3727/45/38/385304.
  25. ↑ Nakhaie, S.; et al. (2015). "Synthesis of atomically thin hexagonal boron nitride films on nickel foils by molecular beam epitaxy". Appl. Phys. Lett. 106 (21): 213108. arXiv: 1501.06606 . Bibcode:2015ApPhL.106u3108N. doi:10.1063/1.4921921. S2CID   32683376.
  26. ↑ Yang, X.; et al. (2013). "Facile synthesis of large-area ultrathin hexagonal BN films via self-limiting growth at the molten B2O3 surface". Small. 9 (8): 1353–8. doi:10.1002/smll.201203126. PMID   23494990.
This page is based on this Wikipedia article
Text is available under the CC BY-SA 4.0 license; additional terms may apply.
Images, videos and audio are available under their respective licenses.