Telescoping bolt

Last updated
Two 9x19mm submachine guns with 250 mm (10 inch) barrels, an Uzi (with a telescoping bolt) and MP40 (without), showing the compactness a telescoping mechanism allows TelescopingBolt-Externals-1.png
Two 9×19mm submachine guns with 250 mm (10 inch) barrels, an Uzi (with a telescoping bolt) and MP40 (without), showing the compactness a telescoping mechanism allows
Internal mechanisms of the above submachine guns. Barrels are blue, bolts are green. TelescopingBolt-Internals-3.png
Internal mechanisms of the above submachine guns. Barrels are blue, bolts are green.

A telescoping bolt (also known as an overhung bolt) is a firearm bolt which telescopes over, that is, wraps around and past, the breech end of the barrel. This feature reduces the required length of a weapon such as a submachine gun significantly, and it allows compact designs to be balanced around the pistol grip in a way that gives "pointability" more like a pistol's.

Contents

While it would be simpler and easier to shorten the bolt to fit completely behind the breech, the bolt must have a certain amount of mass in order to operate reliably with a given caliber. The telescoping bolt moves some of that mass forward of the bolt face, resulting in a bolt which may be longer overall, but is shorter behind the bolt face.

Though technically a different, distinct concept, nearly all telescoping bolt submachine guns use a magazine located in the pistol grip used to hold and fire the weapon. However, there are blowback firearms with the magazine located in the grip that do not use a telescoping bolt, such as Kel-Tec SUB-2000.

History

The telescoping bolt concept first appeared on semi-automatic handguns around the turn of the 20th century. These pistols, starting with the FN M1900 and to continuing to the present, often feature a slide, which acts as both a barrel shroud and the bolt. Moreover, a Belgian pocket pistol patented in 1909 [1] featured a cylindrical bolt wrapped around the barrel instead of a now-conventional slide, which is sometimes claimed to be the first true telescoping bolt design. [2]

One of the earliest submachine gun known to use the telescoping bolt concept was the Italian Armaguerra OG-43, followed by the OG-44, designed by Giovanni Oliani during the later stages of the Second World War. The bolt was "L" shaped and ran in a tube above the chamber and barrel. Both designs did not reach mass production due to wartime events. [3]

The first production model submachine gun using a telescoping bolt was the Czechoslovak Cz 23 aka Sa.23 or vz.48b series, first produced in 1948. These submachine guns use a cylindrical telescoping bolt with centered barrel. While widely exported in the third world, the Cz 23 series was not well known in the west. [4]

The first popularly well-known example was the Uzi submachine gun, designed in Israel by Uziel Gal, a designer inspired by the Cz 23 series. It uses a rectangular bolt, with a barrel which is offset toward the bottom of the bolt. This configuration places the axis of recoil lower, increasing the controllability of the weapon in full-automatic fire. The Uzi was designed in 1948 after the first models of the Cz 23 were seen, and entered service in 1954 (after official adoption in 1951).

The telescoping bolt has subsequently been used in a wide variety of submachine gun designs.

Comparisons

As the image diagrams demonstrate, the basic concept of a telescoping bolt with the magazine well in the handgrip produces significantly more compact weapons. These diagrams show the 1938 design (1939 service) MP-40 submachine gun, which is 630 mm (25 inch) long with the stock folded, weighing four kilograms (8.8 pounds) and having a 251 mm (9.9 inch) barrel, and the (similar materials and production technology) Uzi, a 1948 design (1951 adoption with 1954 service), which is 470 mm (19 inch) long with the stock folded, weighing 3.5 kilograms (7.7 pounds) and having a 260 mm (10.2 inch) barrel.

Utilizing nothing more than a configuration change, and the same materials and fabrication technologies, the Uzi is thus 500 grams (1.1 lb) lighter and 160 mm (6 inches) shorter overall, despite having a longer barrel by 9 mm (0.3 inch).

Examples

Related Research Articles

<span class="mw-page-title-main">Firearm</span> Gun for an individual

A firearm is any type of gun that uses an explosive charge and is designed to be readily carried and used by an individual. The term is legally defined further in different countries.

<span class="mw-page-title-main">Machine pistol</span> Fully automatic handgun

A machine pistol is a handgun that is capable of fully automatic fire, including stockless handgun-style submachine guns.

<span class="mw-page-title-main">Submachine gun</span> Type of automatic firearm

A submachine gun (SMG) is a magazine-fed automatic carbine designed to fire handgun cartridges. The term "submachine gun" was coined by John T. Thompson, the inventor of the Thompson submachine gun, to describe its design concept as an automatic firearm with notably less firepower than a machine gun. As a machine gun must fire rifle cartridges to be classified as such, submachine guns are not considered machine guns.

<span class="mw-page-title-main">Uzi</span> Family of Israeli submachine guns

The Uzi is a family of Israeli open-bolt, blowback-operated submachine guns and machine pistols first designed by Major Uziel "Uzi" Gal in the late 1940s, shortly after the establishment of the State of Israel. It is one of the first weapons to incorporate a telescoping bolt design, which allows the magazine to be housed in the pistol grip for a shorter weapon.

<span class="mw-page-title-main">Action (firearms)</span> Functional mechanism of breech-loading

In firearms terminology, an action is the functional mechanism of a breech-loading firearm that handles the ammunition cartridges, or the method by which that mechanism works. Actions are technically not present on muzzleloaders, as all those are single-shot firearms with a closed off breech with the powder and projectile manually loaded from the muzzle. Instead, the muzzleloader ignition mechanism is referred to as the lock.

<span class="mw-page-title-main">Sten</span> Family of submachine guns

The STEN is a British submachine gun chambered in 9×19mm which was used extensively by British and Commonwealth forces throughout World War II and during the Korean War. The Sten paired a simple design with a low production cost, facilitating mass production to meet the demand for submachine guns.

<span class="mw-page-title-main">MAC-10</span> American machine pistol

The Military Armament Corporation Model 10, officially abbreviated as "M10" or "M-10", and more commonly known as the MAC-10, is a compact, blowback operated machine pistol/submachine gun that was developed by Gordon Ingram in 1964. It is chambered in either .45 ACP or 9mm. A two-stage suppressor by Sionics was designed for the MAC-10, which not only abates the noise created but makes it easier to control on full automatic.

<span class="mw-page-title-main">Semi-automatic pistol</span> Type of pistol

A semi-automatic pistol is a handgun that automatically ejects and loads cartridges in its chamber after every shot fired. Only one round of ammunition is fired each time the trigger is pulled, as the pistol's fire control group disconnects the trigger mechanism from the firing pin/striker until the trigger has been released and reset.

<span class="mw-page-title-main">Open bolt</span> System in firearms

A firearm is said to fire from an open bolt or open breech if, when ready to fire, the bolt and working parts are held to the rear of the receiver, with no round in the chamber. When the trigger is actuated, the bolt travels forward, feeds a cartridge from the magazine or belt into the chamber, and fires that cartridge in the same movement. Like any other self-loading design, the action is cycled by the energy released from the propellant, which sends the bolt back to the rear, compressing the mainspring in readiness for firing the next round. In an open-bolt gun firing semi-automatically, the bolt is caught and held at this point by the sear after each shot; and in automatic open-bolt fire, it's caught and held in this manner whenever the trigger is released. In contrast to this, in closed-bolt guns, the trigger and sear do not affect the movement of the bolt directly.

Blowback is a system of operation for self-loading firearms that obtains energy from the motion of the cartridge case as it is pushed to the rear by expanding gas created by the ignition of the propellant charge.

<span class="mw-page-title-main">Breechblock</span> Part of the firearm action

A breechblock is the part of the firearm action that closes the breech of a breech loading weapon before or at the moment of firing. It seals the breech and contains the pressure generated by the ignited propellant. Retracting the breechblock allows the chamber to be loaded with a cartridge.

<span class="mw-page-title-main">FB PM-63</span> Polish submachine gun

The PM-63 RAK is a Polish 9×18mm submachine gun, designed by Piotr Wilniewczyc in cooperation with Tadeusz Bednarski, Grzegorz Czubak and Marian Wakalski. The RAK combines the characteristics of a self-loading pistol and a fully automatic submachine gun.

<span class="mw-page-title-main">Sa 23</span> Czechoslovakian submachine gun

The CZ Model 23/25 was a series of Czechoslovak designed submachine guns introduced in 1948. There were four generally very similar submachine guns in this series: the Sa 23, Sa 24, Sa 25, and Sa 26. The primary designer was Jaroslav Holeček, chief engineer of the Česká zbrojovka Uherský Brod arms factory.

<span class="mw-page-title-main">Steyr MPi 69</span> Submachine gun

The Steyr MPi 69 is a 9×19mm submachine gun of the late 20th century made by the Austrian firm Steyr.

The MCEM-2 was a prototype submachine gun, which never saw widespread production, but was one of the first submachine guns to combine a wrap-around bolt and the magazine in pistol grip, features later copied in the Czechoslovak Sa vz. 23, Israeli Uzi, among others. The MCEM-2 was the second prototype in a line of experimental submachine guns designed in Britain in 1944. It was envisaged as a possible replacement for the STEN submachine gun then in service. Jerzy Podsedkowski, a Polish constructor who worked on the Vis and Mors and who fled from occupied Poland to Britain, developed the MCEM-2. It is believed that prototypes of MCEM-2 were made before the end of WW2, and its derivatives MCEM-4 and MCEM-6 were tested soon after the war. The latter modifications differed mostly in adoption of the rate-reducing mechanism, incorporated into the trigger unit; the rate of fire therefore was decreased from 1000 to 600 rounds per minute. Nevertheless, neither the prototype was found suitable for adoption, and several years later the British army adopted a more conventional submachine gun, the Sterling-Patchett.

<span class="mw-page-title-main">FMK-3 submachine gun</span> Submachine gun

The FMK-3 is a selective fire blowback-operated submachine gun of Argentinian origin designed by Fabricaciones Militares in 1974. Around 30,000 were produced for the Argentinian military by 1991.

Recoil operation is an operating mechanism used to implement locked-breech autoloading firearms. Recoil operated firearms use the energy of recoil to cycle the action, as opposed to gas operation or blowback operation using the pressure of the propellant gas.

The Parinco mod. 3R is a submachine gun of Spanish origin that was designed in 1959. It is a selective-fire weapon for short-range street and brush fighting. It remains reasonably accurate up to 100 m using sighted semi-automatic fire. For close range combat, 2- or 3-shot bursts are recommended.

<span class="mw-page-title-main">SIG MPX</span> Submachine gun

The SIG MPX is a gas-operated submachine gun designed and manufactured by SIG Sauer, and is primarily chambered in 9×19mm Parabellum. It is a gas-operated firearm featuring a closed, rotating bolt. These design features, rare in submachine guns, were chosen to enhance the safety of the user and to have a more reliable firearm. It was designed in 2013 and was released to the general public in 2015. It features the SIG Sauer short stroke push-rod gas system to reduce the recoil and improve the reliability of the weapon.

The Armaguerra OG-43 and its subsequent version, OG-44, were submachine guns manufactured in small numbers in the Republic of Salo.

References

  1. GB 190920277
  2. https://littlegun.be/arme%20belge/artisans%20identifies%20e%20f/a%20fab%20armes%20reunies%20gb.htm
  3. "Armaguerra OG-43 OG-44". 17 June 2011.
  4. Back to the Roots Archived 2006-11-28 at the Wayback Machine , Monty Mendenhall, at , accessed Jan 10, 2007