Thermal degradation of polymers

Last updated

In polymers, such as plastics, thermal degradation refers to a type of polymer degradation where damaging chemical changes take place at elevated temperatures, without the simultaneous involvement of other compounds such as oxygen. [1] [2] Simply put, even in the absence of air, polymers will begin to degrade if heated high enough. It is distinct from thermal-oxidation, which can usually take place at less elevated temperatures. [3]

Contents

The onset of thermal degradation dictates the maximum temperature at which a polymer can be used. It is an important limitation in how the polymer is manufactured and processed. For instance, polymers become less viscous at higher temperatures which makes injection moulding easier and faster, but thermal degradation places a ceiling temperature on this. Polymer devolatilization is similarly effected. At high temperatures, the components of the long chain backbone of the polymer can break (chain scission) and react with one another (cross-link) to change the properties of the polymer. These reactions result in changes to the molecular weight (and molecular weight distribution) of the polymer and can affect its properties by causing reduced ductility and increased embrittlement, chalking, scorch, colour changes, cracking and general reduction in most other desirable physical properties. [4]

Reaction pathways

Depolymerisation

Under thermal effect, the end of polymer chain departs, and forms low free radical which has low activity. Then according to the chain reaction mechanism, the polymer loses the monomer one by one. However, the molecular chain doesn't change a lot in a short time. The reaction is shown below. [5] This process is common for polymethymethacrylate (perspex).

CH2-C(CH3)COOCH3-CH2-C*(CH3)COOCH3→CH2-C*(CH3)COOCH3 + CH2=C(CH3)COOCH3

Side-group elimination

Groups that are attached to the side of the backbone are held by bonds which are weaker than the bonds connecting the chain. When the polymer is heated, the side groups are stripped off from the chain before it is broken into smaller pieces. For example, the PVC eliminates HCl, under 100–120 °C.

CH2(Cl)CHCH2CH(Cl)→CH=CH-CH=CH+2HCl

Side group elimination can also proceed in a radical manner. For instance, methyl groups in polypropylene are susceptible to homolysis at high temperatures, leaving radicals on the polymer backbone. [6]

Random chain scission

Radicals formed on the polymer backbone by either hydrogen abstraction side-group elimination can cause the chain to break by beta scission. As a result the molecular weight decreases rapidly. As new free radicals with high reactivity are formed, monomers cannot be a product of this reaction, also intermolecular chain transfer and disproportion termination reactions can occur.

CH2-CH2-CH2-CH2-CH2-CH2-CH2’→ CH2-CH2-CH=CH2 + CH3-CH2-CH2’ or CH2’+CH2=CH-CH2-CH2-CH2-CH3

As polymers approach their ceiling temperature scission starts to take place randomly on the backbone.

Oxidation of the polymer

Although thermal degradation is defined as an oxygen free process it is difficult in practise to completely exclude oxygen. Where this is the case thermal oxidation is to be expected, leading to the formation of free radicals by way of hydroperoxides. These may then participate in thermal degradation reactions, accelerating the rate of breakdown.

Analytical Methods

TGA

(Thermogravimetric analysis) (TGA) refers to the techniques where a sample is heated in a controlled atmosphere at a defined heating rate whilst the sample's mass is measured. When a polymer sample degrades, its mass decreases due to the production of gaseous products like carbon monoxide, water vapour and carbon dioxide.

DTA and DSC

(Differential thermal analysis) (DTA) and (differential scanning calorimetry) (DSC): Analyzing the heating effect of polymer during the physical changes in terms of glass transition, melting, and so on. [7] These techniques measure the heat flow associated with oxidation.

See also

Related Research Articles

<span class="mw-page-title-main">Polymer</span> Substance composed of macromolecules with repeating structural units

A polymer (;) is a substance or material consisting of very large molecules called macromolecules, composed of many repeating subunits. Due to their broad spectrum of properties, both synthetic and natural polymers play essential and ubiquitous roles in everyday life. Polymers range from familiar synthetic plastics such as polystyrene to natural biopolymers such as DNA and proteins that are fundamental to biological structure and function. Polymers, both natural and synthetic, are created via polymerization of many small molecules, known as monomers. Their consequently large molecular mass, relative to small molecule compounds, produces unique physical properties including toughness, high elasticity, viscoelasticity, and a tendency to form amorphous and semicrystalline structures rather than crystals.

<span class="mw-page-title-main">Polymerization</span> Chemical reaction to form polymer chains

In polymer chemistry, polymerization, or polymerisation, is a process of reacting monomer molecules together in a chemical reaction to form polymer chains or three-dimensional networks. There are many forms of polymerization and different systems exist to categorize them.

<span class="mw-page-title-main">Polyethylene</span> Most common thermoplastic polymer

Polyethylene or polythene (abbreviated PE; IUPAC name polyethene or poly(methylene)) is the most commonly produced plastic. It is a polymer, primarily used for packaging (plastic bags, plastic films, geomembranes and containers including bottles, etc.). As of 2017, over 100 million tonnes of polyethylene resins are being produced annually, accounting for 34% of the total plastics market.

<span class="mw-page-title-main">Differential scanning calorimetry</span> Thermoanalytical technique

Differential scanning calorimetry (DSC) is a thermoanalytical technique in which the difference in the amount of heat required to increase the temperature of a sample and reference is measured as a function of temperature. Both the sample and reference are maintained at nearly the same temperature throughout the experiment. Generally, the temperature program for a DSC analysis is designed such that the sample holder temperature increases linearly as a function of time. The reference sample should have a well-defined heat capacity over the range of temperatures to be scanned. Additionally, the reference sample must be stable, of high purity, and must not experience much change across the temperature scan. Typically, reference standards have been metals such as indium, tin, bismuth, and lead, but other standards such as polyethylene and fatty acids have been proposed to study polymers and organic compounds, respectively.

<span class="mw-page-title-main">Thermoplastic</span> Plastic that softens with heat and hardens on cooling

A thermoplastic, or thermosoftening plastic, is any plastic polymer material that becomes pliable or moldable at a certain elevated temperature and solidifies upon cooling.

<span class="mw-page-title-main">Polypropylene</span> Thermoplastic polymer

Polypropylene (PP), also known as polypropene, is a thermoplastic polymer used in a wide variety of applications. It is produced via chain-growth polymerization from the monomer propylene.

In polymer chemistry, an addition polymer is a polymer that forms by simple linking of monomers without the co-generation of other products. Addition polymerization differs from condensation polymerization, which does co-generate a product, usually water. Addition polymers can be formed by chain polymerization, when the polymer is formed by the sequential addition of monomer units to an active site in a chain reaction, or by polyaddition, when the polymer is formed by addition reactions between species of all degrees of polymerization. Addition polymers are formed by the addition of some simple monomer units repeatedly. Generally polymers are unsaturated compounds like alkenes, alkalines etc. The addition polymerization mainly takes place in free radical mechanism. The free radical mechanism of addition polymerization completed by three steps i.e. Initiation of free radical, Chain propagation, Termination of chain.

<span class="mw-page-title-main">Polymer degradation</span> Alteration in the polymer properties under the influence of environmental factors

Polymer degradation is the reduction in the physical properties of a polymer, such as strength, caused by changes in its chemical composition. Polymers and particularly plastics are subject to degradation at all stages of their product life cycle, including during their initial processing, use, disposal into the environment and recycling. The rate of this degradation varies significantly; biodegradation can take decades, whereas some industrial processes can completely decompose a polymer in hours.

<span class="mw-page-title-main">Copolymer</span> Polymer derived from more than one species of monomer

In polymer chemistry, a copolymer is a polymer derived from more than one species of monomer. The polymerization of monomers into copolymers is called copolymerization. Copolymers obtained from the copolymerization of two monomer species are sometimes called bipolymers. Those obtained from three and four monomers are called terpolymers and quaterpolymers, respectively. Copolymers can be characterized by a variety of techniques such as NMR spectroscopy and size-exclusion chromatography to determine the molecular size, weight, properties, and composition of the material.

<span class="mw-page-title-main">Thermogravimetric analysis</span> Thermal method of analysis

Thermogravimetric analysis or thermal gravimetric analysis (TGA) is a method of thermal analysis in which the mass of a sample is measured over time as the temperature changes. This measurement provides information about physical phenomena, such as phase transitions, absorption, adsorption and desorption; as well as chemical phenomena including chemisorptions, thermal decomposition, and solid-gas reactions.

<span class="mw-page-title-main">Chain-growth polymerization</span> Polymerization technique

Chain-growth polymerization (AE) or chain-growth polymerisation (BE) is a polymerization technique where unsaturated monomer molecules add onto the active site on a growing polymer chain one at a time. There are a limited number of these active sites at any moment during the polymerization which gives this method its key characteristics.

<span class="mw-page-title-main">Methyl methacrylate</span> Chemical compound

Methyl methacrylate (MMA) is an organic compound with the formula CH2=C(CH3)COOCH3. This colorless liquid, the methyl ester of methacrylic acid (MAA), is a monomer produced on a large scale for the production of poly(methyl methacrylate) (PMMA).

In polymer chemistry, vinyl polymers are a group of polymers derived from substituted vinyl monomers. Their backbone is an extended alkane chain [−CH2−CHR−]. In popular usage, "vinyl" refers only to polyvinyl chloride (PVC).

Autoxidation refers to oxidations brought about by reactions with oxygen at normal temperatures, without the intervention of flame or electric spark. The term is usually used to describe the gradual degradation of organic compounds in air at ambient temperatures. Many common phenomena can be attributed to autoxidation, such as food going rancid, the 'drying' of varnishes and paints, and the perishing of rubber. It is also an important concept in both industrial chemistry and biology. Autoxidation is therefore a fairly broad term and can encompass examples of photooxygenation and catalytic oxidation.

In polymer chemistry, a repeat unit or repeating unit is a part of a polymer whose repetition would produce the complete polymer chain by linking the repeat units together successively along the chain, like the beads of a necklace.

Polymer stabilizers are chemical additives which may be added to polymeric materials, such as plastics and rubbers, to inhibit or retard their degradation. Common polymer degradation processes include oxidation, UV-damage, thermal degradation, ozonolysis, combinations thereof such as photo-oxidation, as well as reactions with catalyst residues, dyes, or impurities. All of these degrade the polymer at a chemical level, via chain scission, uncontrolled recombination and cross-linking, which adversely affects many key properties such as strength, malleability, appearance and colour.

Accelerated photo-ageing of polymers in SEPAP units is the controlled polymer degradation and polymer coating degradation under lab or natural conditions.

<span class="mw-page-title-main">Photo-oxidation of polymers</span>

In polymer chemistry photo-oxidation is the degradation of a polymer surface due to the combined action of light and oxygen. It is the most significant factor in the weathering of plastics. Photo-oxidation causes the polymer chains to break, resulting in the material becoming increasingly brittle. This leads to mechanical failure and, at an advanced stage, the formation of microplastics. In textiles the process is called phototendering.

<span class="mw-page-title-main">Polymer characterization</span>

Polymer characterization is the analytical branch of polymer science.

Chain scission is a term used in polymer chemistry describing the degradation of a polymer main chain. It is often caused by thermal stress (heat) or ionizing radiation, often involving oxygen. During chain cleavage, the polymer chain is broken at a random point in the backbone to form two - mostly still highly molecular - fragments.

References

  1. ↑ Pielichowski, Krzysztof (2005). Thermal degradation of polymeric materials. Shawbury: Rapra Technology. ISBN   9781859574980.
  2. ↑ Guaita, M.; Chiantore, O.; Costa, L. (1985). "Changes in degree of polymerization in the thermal degradation of polystyrene". Polymer Degradation and Stability. 12 (4): 315–332. doi:10.1016/0141-3910(85)90123-5.
  3. ↑ Peterson, Jeffery D.; Vyazovkin, Sergey; Wight, Charles A. (2001). "Kinetics of the Thermal and Thermo-Oxidative Degradation of Polystyrene, Polyethylene and Poly(propylene)". Macromolecular Chemistry and Physics. 202 (6): 775–784. doi:10.1002/1521-3935(20010301)202:6<775::AID-MACP775>3.0.CO;2-G.
  4. ↑ Thermal Degradation of Polymers – The Zeus Polymer Minute
  5. ↑ Liden, David R. (2018). "Thermal and Oxidative Degradation of Polymers". A Century of excellence in measurements, standards, and technology (PDF). Boca Raton, FL: CRC Press. p. 344. ISBN   9781351069397.
  6. ↑ Nguyen, Thu Anh; Ichise, Shota; Kinashi, Kenji; Sakai, Wataru; Tsutsumi, Naoto; Okubayashi, Satoko (February 2022). "Spin Trapping Analysis of the Thermal Degradation of Polypropylene". Polymer Degradation and Stability. 197: 109871. doi:10.1016/j.polymdegradstab.2022.109871. S2CID   246886283.
  7. ↑ M. A. Villetti, J. S. Crespo,M. S. Soldi, A. T. N. Pires, R. Borsali and V. Soldi. Thermal degradation of natural polymers. Journal of Thermal Analysis and Calorimetry, Vol. 67 (2002) 295~303
This page is based on this Wikipedia article
Text is available under the CC BY-SA 4.0 license; additional terms may apply.
Images, videos and audio are available under their respective licenses.