United States Air Force Stability and Control Digital DATCOM

Last updated

The United States Air Force Stability and Control Digital DATCOM is a computer program that implements the methods contained in the USAF Stability and Control DATCOM to calculate the static stability, control and dynamic derivative characteristics of fixed-wing aircraft. Digital DATCOM requires an input file containing a geometric description of an aircraft, and outputs its corresponding dimensionless stability derivatives according to the specified flight conditions. The values obtained can be used to calculate meaningful aspects of flight dynamics.

Contents

History

In February 1976, work commenced to automate the methods contained in the USAF Stability and Control DATCOM, specifically those contained in sections 4, 5, 6 and 7. The work was performed by the McDonnell Douglas Corporation under contract with the United States Air Force in conjunction with engineers at the Air Force Flight Dynamics Laboratory in Wright-Patterson Air Force Base. Implementation of the Digital DATCOM concluded in November 1978.

The program is written in FORTRAN IV and has since been updated; however, the core of the program remains the same.

A report was published, separated into three volumes, which explains the use of Digital DATCOM. The report consists of

Inputs

Section 3 of the USAF Digital DATCOM Manual Volume I defines the inputs available for modeling an aircraft. The inputs are categorized by namelists to facilitate reading the file into FORTRAN.

Flight conditions and options

The FLTCON Namelist describes the flight conditions for the case. A maximum of 400 Mach-altitude combinations can be run at once, with up to 20 angles of attack for each combination. The user can specify whether the Mach number and altitude varies together, the Mach number varies at a constant altitude, or the altitude varies at a constant Mach number. Both subsonic and supersonic analysis can be run in Digital DATCOM.

The OPTINS Namelist defines the reference parameters for the aircraft. The theoretical wing area, mean aerodynamic chord, and wing span are input along with a parameter defining the surface roughness of the aircraft.

Synthesis parameters

The SYNTHS Namelist allows the user to define the positions of the center of gravity and apexes of the wings. The X- and Z- coordinates are needed for the wing, horizontal tail, and vertical tail in order for the aircraft to be synthesized correctly. DATCOM does not require that the origin for the aircraft has to be the nose of the aircraft; any arbitrary point will do, but all of the dimensions need to be referenced from that point. Incidence angles can also be added to the wing and horizontal tail.

Body parameters

The BODY Namelist defines the shape of the body. Digital DATCOM assumes an axisymmetrical shape for the body. Up to 20 stations can be specified with the fuselage half-width, upper coordinate and lower coordinate being defined at each station. For supersonic analysis, additional parameters can be input.

Wing, Horizontal and Vertical Tail parameters

The WGPLNF, HTPLNF and VTPLNF Namelists define the wing, horizontal tail and vertical tail, respectively. The basic parameters such as root chord, tip chord, half-span, twist, dihedral and sweep are input. Digital DATCOM also accepts wing planforms which change geometry along the span such as the F4 Phantom II which had 15 degrees of outboard dihedral.

Canards can also be analyzed in Digital DATCOM. The canard must be specified as the forward lifting surface (i.e. wing) and the wing as the aft lift surface.

For airfoil designations, most traditional NACA 4-, 5-, and 6- airfoils can be specified in Digital DATCOM. Additionally, custom airfoils can be input using the appropriate namelists. Also, twin vertical tails can be designated in Digital DATCOM, but not twin booms.

High Lift and Control Devices

Using the SYMFLP and ASYFLP Namelists, flaps, elevators, and ailerons can be defined. Digital DATCOM allows a multitude of flap types including plain, single-slotted, and fowler flaps. Up to 9 flap deflections can be analyzed at each Mach-altitude combination. Unfortunately, the rudder is not implemented in Digital DATCOM.

Digital DATCOM also offers an automated aircraft TRIM function which calculates elevator deflections needed to trim the aircraft.

Other Inputs

Other Digital DATCOM inputs include power effects (propeller and jet), ground effects, trim tabs, and experimental data. The EXPRXX Namelist allows a user to use experimental data (such as coefficient of lift, coefficient of drag, etc.) in lieu of the data Digital DATCOM produces in the intermediate steps of its component build-up.

All dimensions are taken in feet and degrees unless specified otherwise. Digital DATCOM provides commands for outputting the dynamic derivatives (DAMP) as well as the stability coefficients of each components (BUILD).

Output

Digital DATCOM produces a copious amount of data for the relatively small amount of inputs it requires. By default, only the data for the aircraft is output, but additional configurations can be output:

For each configuration, stability coefficients and derivatives are output at each angle of attack specified. The details of this output are defined in Section 6 of the USAF Digital DATCOM Manual Volume I. The basic output includes:

For complete aircraft configurations, downwash data is also included.

When compared with modern methods of computational fluid dynamics, Digital DATCOM may seem antiquated. However, in its day, the program was an advanced estimation tool, and certainly much faster than plowing through pages and pages of engineering texts. Digital DATCOM is no longer supported by the USAF and is now public domain software.

Limitations

Inlets, external stores, and other protuberances cannot be input because Digital DATCOM analyzes the fuselage as a body of revolution. The simplification affects the coefficient of drag for the aircraft.

Dynamic derivatives are not output for aircraft that have wings that are not straight-tapered or have leading edge extensions. This problem can be overcome by using experimental data for the wing-body (using non-straight tapered wing).

There is no method to input twin vertical tails mounted on the fuselage, although there is a method for H-Tails. This problem can be addressed by approximating the twin vertical tails as a single equivalent vertical tail mounted to the fuselage.

Digital DATCOM cannot provide outputs for the control derivatives with regard to the rudder control surface. According to the manual, there is no any input parameters which define the geometry of rudder.

Digital DATCOM cannot analyze three lifting surfaces at once, such as a canard-wing-horizontal tail configuration. This problem can be addressed by superposition of lifting surfaces through the experimental input option.

Current Development

There are intentions among those that use this package to improve the overall package, through an easier user interface, as well as more comprehensive output data.

Citation in AC3D Citation ac.jpg
Citation in AC3D

DATCOM+

While the original DIGDAT program has been left relatively untouched, there has been a new front-end created that will allow the user to name the input file with something more significant than FOR005.DAT. The new input file format allows the user to place comments in the input file. There have also been hooks placed in the DIGDAT that allow for alternate outputs in addition to the original output format, which is 132 columns wide and not easily imported into another application. There is a graphical representation of the aircraft output in AC3D, as well as data table output in XML for the JSBSim and FlightGear projects, as well as a free-format LFI (Linear Function Interpolation) data table file.

Along with the DIGDAT program, there are viewers for the AC3D, XML, and LFI format output files. Data tables can easily be output to the screen or to PNG files for inclusion into reports.

Navion in MATLAB Navion in Datcom3d.jpg
Navion in MATLAB

Mathworks Aerospace Toolbox

Aerospace Toolbox includes a function for importing output files from Digital DATCOM into MATLAB. This function lets you collect aerodynamic coefficients from static and dynamic analyses and transfer them into MATLAB as a cell array of structures, with each structure containing information about a Digital DATCOM output file.

OpenDatcom

OpenDatcom is an open-source GUI for the Digital DATCOM created and hosted by the OpenAE community. OpenDatcom incorporates all the basic (non-experimental) functionality supported by the Digital DATCOM while providing real-time input error and bounds checking. An alpha version of the program was released November 1, 2009 to the general public. The OpenAE.org web site is no longer active.

Predicting Aerodynamics of Structurally Damaged Aircraft

There has been some research in using Digital DATCOM in conjunction with wind tunnel studies to predict aerodynamics of structurally impaired aircraft. Dr. Bilal Siddiqui at DHA Suffa University presented an approach [1] to predict the nonlinear aerodynamics of a structurally damaged aircraft model based on the engineering level aerodynamic prediction methods, DATCOM. Raw results from the code provide good correlation with wind tunnel data at very low angles of attack, but accuracy deteriorates rapidly as the angle of attack increases. A new methodology is then proposed which combines the experimental results of healthy aircraft with the predicted aerodynamics of the damaged cases, to yield better correlation between experimental and predicted aerodynamic coefficients for damaged aircraft. Three damage-configurations are studied at supersonic speeds. The methodology can be used to quickly generate aerodynamic model for damaged aircraft for simulation and reconfigurable control.

See also

Related Research Articles

<span class="mw-page-title-main">Stall (fluid dynamics)</span> Abrupt reduction in lift due to flow separation

In fluid dynamics, a stall is a reduction in the lift coefficient generated by a foil as angle of attack increases. This occurs when the critical angle of attack of the foil is exceeded. The critical angle of attack is typically about 15°, but it may vary significantly depending on the fluid, foil, and Reynolds number.

In fluid mechanics, the center of pressure is the point where the total sum of a pressure field acts on a body, causing a force to act through that point. The total force vector acting at the center of pressure is the surface integral of the pressure vector field across the surface of the body. The resultant force and center of pressure location produce an equivalent force and moment on the body as the original pressure field.

<span class="mw-page-title-main">Aircraft flight dynamics</span> Science of air vehicle orientation and control in three dimensions

Flight dynamics is the science of air vehicle orientation and control in three dimensions. The three critical flight dynamics parameters are the angles of rotation in three dimensions about the vehicle's center of gravity (cg), known as pitch, roll and yaw. These are collectively known as aircraft attitude, often principally relative to the atmospheric frame in normal flight, but also relative to terrain during takeoff or landing, or when operating at low elevation. The concept of attitude is not specific to fixed-wing aircraft, but also extends to rotary aircraft such as helicopters, and dirigibles, where the flight dynamics involved in establishing and controlling attitude are entirely different.

<span class="mw-page-title-main">Angle of attack</span> Angle between the chord of a wing and the undisturbed airflow

In fluid dynamics, angle of attack is the angle between a reference line on a body and the vector representing the relative motion between the body and the fluid through which it is moving. Angle of attack is the angle between the body's reference line and the oncoming flow. This article focuses on the most common application, the angle of attack of a wing or airfoil moving through air.

<span class="mw-page-title-main">Flight control surfaces</span> Surface that allows a pilot to adjust and control an aircrafts flight attitude

Aircraft flight control surfaces are aerodynamic devices allowing a pilot to adjust and control the aircraft's flight attitude.

<span class="mw-page-title-main">Dihedral (aeronautics)</span> Angle between each wing or tail surface within a pair

In aeronautics, dihedral is the angle between the left and right wings of an aircraft. "Dihedral" is also used to describe the effect of sideslip on the rolling of the aircraft.

<span class="mw-page-title-main">Stabilator</span>

A stabilator is a fully movable aircraft horizontal stabilizer. It serves the usual functions of longitudinal stability, control and stick force requirements otherwise performed by the separate parts of a conventional horizontal stabilizer and elevator. Apart from reduced drag, particularly at high Mach numbers, it is a useful device for changing the aircraft balance within wide limits, and for reducing stick forces.

<span class="mw-page-title-main">Empennage</span> Tail section of an aircraft containing stabilizers

The empennage, also known as the tail or tail assembly, is a structure at the rear of an aircraft that provides stability during flight, in a way similar to the feathers on an arrow. The term derives from the French language verb empenner which means "to feather an arrow". Most aircraft feature an empennage incorporating vertical and horizontal stabilising surfaces which stabilise the flight dynamics of yaw and pitch, as well as housing control surfaces.

Aircraft flight mechanics are relevant to fixed wing and rotary wing (helicopters) aircraft. An aeroplane, is defined in ICAO Document 9110 as, "a power-driven heavier than air aircraft, deriving its lift chiefly from aerodynamic reactions on surface which remain fixed under given conditions of flight".

<span class="mw-page-title-main">Vertical stabilizer</span> Aircraft component

A vertical stabilizer or tail fin is the static part of the vertical tail of an aircraft. The term is commonly applied to the assembly of both this fixed surface and one or more movable rudders hinged to it. Their role is to provide control, stability and trim in yaw. It is part of the aircraft empennage, specifically of its stabilizers.

<span class="mw-page-title-main">Stabilizer (aeronautics)</span> Aircraft component

An aircraft stabilizer is an aerodynamic surface, typically including one or more movable control surfaces, that provides longitudinal (pitch) and/or directional (yaw) stability and control. A stabilizer can feature a fixed or adjustable structure on which any movable control surfaces are hinged, or it can itself be a fully movable surface such as a stabilator. Depending on the context, "stabilizer" may sometimes describe only the front part of the overall surface.

In aeronautics, inertia coupling, also referred to as inertial coupling and inertial roll coupling, is a potentially catastrophic phenomenon of high-speed flight which caused the loss of aircraft and pilots before the design features to counter it were understood. It occurs when the inertia of a heavy fuselage exceeds the ability of the aerodynamic forces and moments generated by the wing and empennage to stabilize the aircraft. The problem became apparent as jet fighter aircraft and research aircraft were developed with narrow wingspans, that had relatively low roll inertia, caused by a long slender high-density fuselage, compared to the pitch and yaw inertias.

<span class="mw-page-title-main">Canard (aeronautics)</span> Aircraft configuration in which a small wing is placed in front of the main wing

In aeronautics, a canard is a wing configuration in which a small forewing or foreplane is placed forward of the main wing of a fixed-wing aircraft or a weapon. The term "canard" may be used to describe the aircraft itself, the wing configuration, or the foreplane. Canard wings are also extensively used in guided missiles and smart bombs.

<span class="mw-page-title-main">Tailless aircraft</span> Aircraft whose only horizontal aerodynamic surface is its main wing

In aeronautics, a tailless aircraft is an aircraft with no other horizontal aerodynamic surface besides its main wing. It may still have a fuselage, vertical tail fin, and/or vertical rudder.

In flight dynamics, longitudinal stability is the stability of an aircraft in the longitudinal, or pitching, plane. This characteristic is important in determining whether an aircraft pilot will be able to control the aircraft in the pitching plane without requiring excessive attention or excessive strength.

The United States Air Force Stability and Control DATCOM is a collection, correlation, codification, and recording of best knowledge, opinion, and judgment in the area of aerodynamic stability and control prediction methods. It presents substantiated techniques for use (1) early in the design or concept study phase, (2) to evaluate changes resulting from proposed engineering fixes, and (3) as a training on crosstraining aid. It bridges the gap between theory and practice by including a combination of pertinent discussion and proven practical methods. For any given configuration and flight condition, a complete set of stability and control derivatives can be determined without resort to outside information.

<span class="mw-page-title-main">Wing configuration</span> Describes the general shape and layout of an aircraft wing

The wing configuration of a fixed-wing aircraft is its arrangement of lifting and related surfaces.

Flight dynamics in aviation and spacecraft, is the study of the performance, stability, and control of vehicles flying through the air or in outer space. It is concerned with how forces acting on the vehicle determine its velocity and attitude with respect to time.

<span class="mw-page-title-main">Three-surface aircraft</span> Fixed-wing aircraft with a main central wing plus fore and aft surfaces

A three-surface aircraft or sometimes three-lifting-surface aircraft has a foreplane, a central wing and a tailplane. The central wing surface always provides lift and is usually the largest, while the functions of the fore and aft planes may vary between types and may include lift, control and/or stability.

This glossary of aerospace engineering terms pertains specifically to aerospace engineering, its sub-disciplines, and related fields including aviation and aeronautics. For a broad overview of engineering, see glossary of engineering.

References