Vegetation and slope stability

Last updated

Vegetation and slope stability are interrelated by the ability of the plant life growing on slopes to both promote and hinder the stability of the slope. The relationship is a complex combination of the type of soil, the rainfall regime, the plant species present, the slope aspect, and the steepness of the slope. Knowledge of the underlying slope stability as a function of the soil type, its age, horizon development, compaction, and other impacts is a major underlying aspect of understanding how vegetation can alter the stability of the slope. [1] There are four major ways in which vegetation influences slope stability: wind throwing, the removal of water, mass of vegetation (surcharge), and mechanical reinforcement of roots.

Contents

Wind throwing

Wind throw is the toppling of a tree due to the force of the wind, this exposes the root plate and adjacent soil beneath the tree and influences slope stability. Wind throw is a factor when considering one tree on a slope; however, it is of lesser importance when considering general slope stability for a body of trees as the wind forces involved represent a smaller percentage of the potential disturbing forces and the trees which are in the centre of the group will be sheltered by those on the outside. [2]

Water transpiration Surface water cycle.svg
Water transpiration

Removal of water

Vegetation influences slope stability by removing water through transpiration. Transpiration is the vaporisation of liquid water contained in plant tissue and the vapour removal to the air. [3] Water is drawn up from the roots and transported through the plant up to the leaves.

The major effect of transpiration is the reduction of soil pore water pressures which counteracts the loss of strength which occurs through wetting, this is most readily seen as a loss of moisture around trees. However it is not easy to rely on tree and shrub roots to remove water from slopes and consequently help ensure slope stability. The ability to transpire in wet conditions is severely reduced and therefore any increase in soil strength previously gained in evaporation and transpiration will be lost or significantly reduced, consequently the effects of transpiration cannot be taken into account at these times. However it can be assumed that the chance of slope failure following saturation by storm events or periods of extended rainfall will be lessened as a result of transpiration. Moreover, although changes in moisture content will affect the undrained shear strength, the effective shear stress parameters as commonly used in routine slope stability analysis are not directly influenced by changing moisture content, although the water pressures (suctions) used in the analysis will change. [2] [3]

It is important to note that desiccation cracks can potentially be extended by vegetation in dry weather promoting the deeper penetration of water to a potential slip plane and increased water pressure into the soil during the wet periods. Nevertheless, these cracks will be filled by roots growing deeper into the soil as they follow the path of least resistance. [2]

Studies in Malaysia [4] have shown that there is a significant relationship between root length density, soil water content and ultimately slope stability. Slopes that had high root density (due to dense vegetation on the surface) were less likely to undergo slope failure. This is because a high root length density results in low soil water content which in turn results in an increase in shear strength and a decrease in soil permeability. It is suggested that root length density and soil water level could be used as indicators of slope stability and possibly could be used to predict future slope failure. [4]

Transpiration is accentuated when the vegetation has an extensive root system and rapid transpiration continues throughout winter. [5]

The removal of water is also affected by the shading provided by vegetation. Shading helps prevent the desiccation of the soils which results in shrinkage and cracking allowing the deep penetration of rain water. Plants need to have a high leaf to root ratio and have the ability to persist through hot summer months in order to provide effective shading of the soils. [5]

The mass of vegetation

The mass of vegetation is only likely to have an influence on slope stability when larger trees are growing on the slope. A tree of 30–50m height is likely to have a loading of approximately 100–150 kN/m2. The larger trees should be planted at the toe of the slope with a potential rotational failure as this could increase the factor of safety by 10%. However, if the tree is planted at the top of the slope this could reduce the factor of safety by 10%. [2] [5]

Each slope stability situation should be considered independently for the vegetation involved. Transpiration will reduce the weight of the slope as moisture is lost. This can be significant on slopes of marginal stability. [2]

If larger trees are removed from the toe area of a slope there will be both a reduction in soil strength due to the loss of evapotranspiration effects and a reduction in applied loading which may result in temporary suctions in clay soils which could lead to softening as the available water is drawn in to compensate for the suction forces. This is similar to the recognised softening of overconsolidated clays due to the relaxation of overburden pressures when placed in the top layers of an embankment from deep cutting. [2]

Mechanical reinforcement of roots

Roots reinforce the soil by growing across failure planes, root columns acting as piles, and by limiting surface erosion. [5] [6] [7]

Root growth across failure planes

When roots grow across the plane of potential failure there is an increase in shear strength by binding particles. The roots anchor the unstable surficial soil into the deeper stable layers or bedrock. [1] This most readily occurs when there is rapid deep growth (1.5m deep) of roots which last for more than two years. However, the strength exerted by roots generally only extends down to 1 m (3.3 ft) while most failures occur between 1.2–1.5 m (3.9–4.9 ft) soil depth. [5]

Root reinforcement model

The root Reinforced Earth root model is the result of the root elongation across a potential slip plane which produces a tensile root force which is transferred to the soil by cohesive and frictional contacts between the root and the soil. [8]

Tensile root strength contribution and pull out resistance

The pull out resistance of a root is the measured resistance of root structure to be pulled out of the ground and is likely to be only a little less than the measured tensile strength of the root which is the roots resistance to breaking as measured in the laboratory. In the cases where there is no pull out data available the tensile strength data maybe used as a rough guide to the maximum pull out resistance available. [2]

The tensile root strength of a range of diameters over a range of species has been tested in the laboratory and has been found to be approximately 5–60 MN/m2. In order for the root to actually enhance slope stability the root must have sufficient embedment and adhesion with the soil. The way that roots interact with the soil is intricate but for engineering purposes the available force contributions may be measured with in situ pull out tests. [2]

Root morphology and modes of failure

The root length and the type of root branching effects the way that root failure occurs [2] [9] Three different modes of failure have been identified in hawthorn roots which relate to the root soil relationship which is shown in the shape of the roots and the shape of the failure curve. Roots which have no branches tend to fail in tension and pull straight out of the ground with minimal resistance. Roots which have multiple branches generally fail in stages as each branch breaks inside the soil. These roots can then separated into two different groups: 1) those that initially reach their maximum peak force and then maintain a high force that progressively decreases as the root branches fail after significant strain and 2) those that break with increasingly applied force. In a number of tests considerable adhesion between a segment of the root and the soil can be measured prior to the root eventually slipping out of the soil mass. [2]

Type A failure

Roots that do not have branches generally fail in tension and pull straight out of the ground with only minimal resistance. The root reaches its maximum pullout resistance then rapidly fails at a weak point. The root easily slips out of the soil due to the gradual tapering (progressive decrease in root diameter along its length) which means that as the root is pulled out it is moving through a space that is larger than its diameter which consequently has no further bonds or interaction with the surrounding soil. [9]

Type B failure

Type B failure occurs when branched roots initially reach their maximum peak resistance then sustain a high resistance which slowly reduces as the branches of the roots fail after significant strain. In some tests considerable adhesion between a section of the root and the soil mass can be measured before the root eventually slips out. Forked roots require a greater force to be pulled out as the cavity above the fork is thinner than the root which is trying to move through the cavity, this can then result in deformation of the soil as the root moves through the soil. [9]

Type C failure

Roots that have multiple branches or forked branches also can undergo tensile failure but predominantly fail in stages as each branch breaks within the soil. These roots break with increasingly applied force in stages in the form of stepped peaks corresponding to the progressive breaking of roots of greater diameters. The root progressively releases its bonds with the soil until final tensile failure. [9]

In some cases when the root has a sinusoidal shape with many small rootlets along its length the root reaches its maximum pull out resistance on straightening and then breaks at the weakest point; however, at this point the root is not pulled out of the soil as it adheres and interacts with the soil producing a residual strength. If pulling was stopped at this point, the root would give increased strength to the soil. However, if the root is completely pulled out of the ground then there is no further interaction with soil and therefore no increase in soil strength is provided. [9]

Factors which affect root pull out resistance

Studies have shown [9] that the pull out resistance of hawthorn and oak roots are affected by intra species differences, inter-species variations and root size (diameter) in a similar as way as root tensile strength varies (as measured in the laboratory). In the pull out test the applied force acting on the root acts across a larger root area, which involves multiple branches, longer lengths) than the short (approximately 150mm) length of root used in tensile strength tests. In a pull out test the root is likely to fail at weak points such as branching points, nodes or damaged areas.

The studies also showed [9] that there is a positive correlation between maximum root pull out resistance and root diameter for hawthorn and oat root. Smaller diameter roots had a lower pull out resistance or breaking force than the larger diameter roots.

Root columns acting as piles

Trees and root columns can prevent shallow mass movement by acting as piles when there is buttressing and soil arching through a woody deep root system which has multiple sinker roots with embedded stems and laterals. [5]

Limitation of surface erosion

Vegetation can also be used to control water erosion by limiting surface processes such as sheet wash and overland flow. [6] [7] Vegetation can provide a considerable contribution to the stability of slope through enhancing soil cohesion. This cohesion is dependent upon the morphological characteristics of root systems and the tensile strength of single roots. [1]

There is considerable evidence of fine roots resisting surface erosion. The role of fine roots in general slope stability is not fully understood. It is thought that the fine roots help keep the surface soil together and prevent surface erosion. The fine root network may have an apparent enhanced cohesion which is comparable to geosynthetic mesh elements. The limitation of surface erosion processes is particularly apparent in areas of shrub and grass where the fine root distribution is consistent and clearly defined; however, cohesion is generally limited to the top 1 m (3.3 ft) of soil. [2]

See also

Related Research Articles

<span class="mw-page-title-main">Xylem</span> Water transport tissue in vascular plants

Xylem is one of the two types of transport tissue in vascular plants, the other being phloem; both of these are part of the vascular bundle. The basic function of the xylem is to transport water upward from the roots to parts of the plants such as stems and leaves, but also transports nutrients. The word xylem is derived from the Ancient Greek word ξύλον (xylon), meaning "wood"; the best-known xylem tissue is wood, though it is found throughout a plant. The term was introduced by Carl Nägeli in 1858.

<span class="mw-page-title-main">Root</span> Basal organ of a vascular plant

In vascular plants, the roots are the organs of a plant that are modified to provide anchorage for the plant and take in water and nutrients into the plant body, which allows plants to grow taller and faster. They are most often below the surface of the soil, but roots can also be aerial or aerating, that is, growing up above the ground or especially above water.

<span class="mw-page-title-main">Evapotranspiration</span> Natural processes of water movement within the water cycle

Evapotranspiration (ET) refers to the combined processes which move water from the Earth's surface into the atmosphere. It covers both water evaporation and transpiration. Evapotranspiration is an important part of the local water cycle and climate, and measurement of it plays a key role in agricultural irrigation and water resource management.

<span class="mw-page-title-main">Root pressure</span> Transverse osmotic pressure within the cells of a root system

Root pressure is the transverse osmotic pressure within the cells of a root system that causes sap to rise through a plant stem to the leaves.

<span class="mw-page-title-main">Arboriculture</span> Management and study of trees and other woody plants

Arboriculture is the cultivation, management, and study of individual trees, shrubs, vines, and other perennial woody plants. The science of arboriculture studies how these plants grow and respond to cultural practices and to their environment. The practice of arboriculture includes cultural techniques such as selection, planting, training, fertilization, pest and pathogen control, pruning, shaping, and removal.

<span class="mw-page-title-main">Slope stability</span> Stability of soil or rock slopes

Slope stability refers to the condition of inclined soil or rock slopes to withstand or undergo movement; the opposite condition is called slope instability or slope failure. The stability condition of slopes is a subject of study and research in soil mechanics, geotechnical engineering, and engineering geology. Analyses are generally aimed at understanding the causes of an occurred slope failure, or the factors that can potentially trigger a slope movement, resulting in a landslide, as well as at preventing the initiation of such movement, slowing it down or arresting it through mitigation countermeasures.

Tilth is a physical condition of soil, especially in relation to its suitability for planting or growing a crop. Factors that determine tilth include the formation and stability of aggregated soil particles, moisture content, degree of aeration, soil biota, rate of water infiltration and drainage. Tilth can change rapidly, depending on environmental factors such as changes in moisture, tillage and soil amendments. The objective of tillage is to improve tilth, thereby increasing crop production; in the long term, however, conventional tillage, especially plowing, often has the opposite effect, causing the soil carbon sponge to oxidize, break down and become compacted.

<span class="mw-page-title-main">Soil moisture</span> Water content of the soil

Soil moisture is the water content of the soil. It can be expressed in terms of volume or weight. Soil moisture measurement can be based on in situ probes or remote sensing methods.

Regarding the civil engineering of shorelines, soft engineering is a shoreline management practice that uses sustainable ecological principles to restore shoreline stabilization and protect riparian habitats. Soft Shoreline Engineering (SSE) uses the strategic placement of organic materials such as vegetation, stones, sand, debris, and other structural materials to reduce erosion, enhance shoreline aesthetic, soften the land-water interface, and lower costs of ecological restoration.

Landslide mitigation refers to several human-made activities on slopes with the goal of lessening the effect of landslides. Landslides can be triggered by many, sometimes concomitant causes. In addition to shallow erosion or reduction of shear strength caused by seasonal rainfall, landslides may be triggered by anthropic activities, such as adding excessive weight above the slope, digging at mid-slope or at the foot of the slope. Often, individual phenomena join to generate instability over time, which often does not allow a reconstruction of the evolution of a particular landslide. Therefore, landslide hazard mitigation measures are not generally classified according to the phenomenon that might cause a landslide. Instead, they are classified by the sort of slope stabilization method used:

<span class="mw-page-title-main">Buffer strip</span>

A buffer strip is an area of land maintained in permanent vegetation that helps to control air quality, soil quality, and water quality, along with other environmental problems, dealing primarily on land that is used in agriculture. Buffer strips trap sediment, and enhance filtration of nutrients and pesticides by slowing down surface runoff that could enter the local surface waters. The root systems of the planted vegetation in these buffers hold soil particles together which alleviate the soil of wind erosion and stabilize stream banks providing protection against substantial erosion and landslides. Farmers can also use buffer strips to square up existing crop fields to provide safety for equipment while also farming more efficiently.

<span class="mw-page-title-main">Cushion plant</span> Plant life-form

A cushion plant is a compact, low-growing, mat-forming plant that is found in alpine, subalpine, arctic, or subarctic environments around the world. The term "cushion" is usually applied to woody plants that grow as spreading mats, are limited in height above the ground, have relatively large and deep tap roots, and have life histories adapted to slow growth in a nutrient-poor environment with delayed reproductivity and reproductive cycle adaptations. The plant form is an example of parallel or convergent evolution with species from many different plant families on different continents converging on the same evolutionary adaptations to endure the harsh environmental conditions.

<span class="mw-page-title-main">Transpiration</span> Process of water moving through a plant parts

Transpiration is the process of water movement through a plant and its evaporation from aerial parts, such as leaves, stems and flowers. It is a passive process that requires no energy expense by the plant. Transpiration also cools plants, changes osmotic pressure of cells, and enables mass flow of mineral nutrients. When water uptake by the roots is less than the water lost to the atmosphere by evaporation, plants close small pores called stomata to decrease water loss, which slows down nutrient uptake and decreases CO2 absorption from the atmosphere limiting metabolic processes, photosynthesis, and growth.

Hydraulic redistribution is a passive mechanism where water is transported from moist to dry soils via subterranean networks. It occurs in vascular plants that commonly have roots in both wet and dry soils, especially plants with both taproots that grow vertically down to the water table, and lateral roots that sit close to the surface. In the late 1980s, there was a movement to understand the full extent of these subterranean networks. Since then it was found that vascular plants are assisted by fungal networks which grow on the root system to promote water redistribution.

<span class="mw-page-title-main">Bank erosion</span> Marginal wear of a watercourse

Bank erosion is the wearing away of the banks of a stream or river. This is distinguished from erosion of the bed of the watercourse, which is referred to as scour.

<span class="mw-page-title-main">Absorption of water</span> Life process in plants

In higher plants water and minerals are absorbed through root hairs which are in contact with soil water and from the root hairs zone a little the root tips.

<span class="mw-page-title-main">River bank failure</span> Natural phenomenon

River bank failure can be caused when the gravitational forces acting on a bank exceed the forces which hold the sediment together. Failure depends on sediment type, layering, and moisture content.

Soil sloughing is soil falling off banks and slopes due to a loss in cohesion. Soil sloughs off for the same reasons as landslides in general, with very wet soil being among the leading factors. Sloughing is a relatively shallow phenomenon involving the uppermost layers of the soil. Bare soils are more likely to slough than soils with plant cover in part because the roots help hold the surface against gravity. Unabated soil sloughing can end in massive bank or slope failure.

<span class="mw-page-title-main">Soil compaction (agriculture)</span> Decrease in porosity of soil due to agriculture

Soil compaction, also known as soil structure degradation, is the increase of bulk density or decrease in porosity of soil due to externally or internally applied loads. Compaction can adversely affect nearly all physical, chemical and biological properties and functions of soil. Together with soil erosion, it is regarded as the "costliest and most serious environmental problem caused by conventional agriculture."

A fine root is most commonly defined as a plant root that is two millimeters or less in diameter. Fine roots may function in acquisition of soil resources and/or resource transport, making them functionally most analogous to the leaves and twigs in a plant's shoot system. Fine-root traits are variable between species and responsive to environmental conditions. Consequently, fine roots are studied to characterize the resource acquisition strategies and competitive ability of plant species. Categories of fine roots have been developed based on root diameter, position in a root system's branching hierarchy, and primary function. Fine roots are often associated with symbiotic fungi and play a role in many ecosystem processes like nutrient cycles and soil reinforcement.

References

  1. 1 2 3 Mattia, C.; Bishetti, G. & Gentile, F. 2005, ‘Biotechnical characteristics of root systems of typical Mediterranean species’, Plant and Soil, vol. 278, no.1, pp. 23–32
  2. 1 2 3 4 5 6 7 8 9 10 11 Greenwood, J.; Norris, J. & Wint, J. 2004, ‘Assessing the contribution of vegetation to slope stability’, Proceedings of the Institution of Civil Engineers, vol. 157, no. 4, pp. 199–207.
  3. 1 2 Food and Agriculture Organisation of the United Nations 2007, Introduction to evapotranspiration, viewed 10 June 2007, http://www.fao.org/docrep/X0490E/x0490e04.htm
  4. 1 2 Osman, N. & Barakabah, S. 2006, ‘Parameters to predict slope stability – Soil water and root profiles’, Ecological Engineering, vol. 28, no. 1, pp. 90–95
  5. 1 2 3 4 5 6 Perry, J., Pedley, M., & Reid, M. 2003, Infrastructure embankments condition appraisal and remedial treatment, MWL Digital, Pontypool, South Wales.
  6. 1 2 Cammeraat, C.; van Beek, R. & Kooijman, A. 2005, ‘Vegetation succession and its consequences for slope stability in SE Spain’, Plant and Soil, vol. 278, no.1, pp. 135–147.
  7. 1 2 Morgan, R. 2007, ‘Vegetative-based technologies for erosion control’, in Stokes, A. (eds), Eco- and Ground Bioengineering: The use of vegetation to Improve Slope Stability, Dordrecht, London, pp. 265–272.
  8. van Beek, L.; Wint, J.; Cammeraat, L. & Edwards, J. 2005, ‘Observation and stimulation of root reinforcement on abandoned Mediterranean slopes’, Plant & Soil, vol. 278, no.1, pp. 55–74.
  9. 1 2 3 4 5 6 7 Norris, J. 2005, ‘Root reinforcement by hawthorn and oak roots on a highway cut-slope in Southern England’, Plant and Soil, vol. 278, no. 1, pp. 43–53.

Sources