In aviation, autoland describes a system that fully automates the landing procedure of an aircraft's flight, with the flight crew supervising the process. Such systems enable airliners to land in weather conditions that would otherwise be dangerous or impossible to operate in.
A few general aviation aircraft have begun to be fitted with "emergency autoland" systems that can be activated by passengers, or by automated crew monitoring systems. The emergency autoland systems are designed to complete an emergency landing at the nearest suitable airport, without any further human intervention, in the event that the flight crew is incapacitated.
Description
Autoland systems were designed to make landing possible in visibility too poor to permit any form of visual landing, although they can be used at any level of visibility. They are usually used when visibility is less than 600 meters runway visual range and/or in adverse weather conditions, although limitations do apply for most aircraft—for example, for a Boeing 747-400 the limitations are a maximum headwind of 25 kts, a maximum tailwind of 10 kts, a maximum crosswind component of 25 kts, and a maximum crosswind with one engine inoperative of five knots. They may also include automatic braking to a full stop once the aircraft is on the ground, in conjunction with the autobrake system, and sometimes auto deployment of spoilers and thrust reversers.
Autoland may be used for any suitably approved instrument landing system (ILS) or microwave landing system (MLS) approach, and is sometimes used to maintain currency of the aircraft and crew, as well as for its main purpose of assisting an aircraft landing in low visibility and/or bad weather.
Autoland requires the use of a radar altimeter to determine the aircraft's height above the ground very precisely so as to initiate the landing flare at the correct height (usually about 50 feet (15m)). The localizer signal of the ILS may be used for lateral control even after touchdown until the pilot disengages the autopilot. For safety reasons, once autoland is engaged and the ILS signals have been acquired by the autoland system, it will proceed to landing without further intervention.
It can be disengaged only by completely disconnecting the autopilot (this prevents accidental disengagement of the autoland system at a critical moment) or by initiating an automatic go-around. At least two and often three independent autopilot systems work in concert to carry out autoland, thus providing redundant protection against failures. Most autoland systems can operate with a single autopilot in an emergency, but they are only certified when multiple autopilots are available.
The autoland system's response rate to external stimuli work very well in conditions of reduced visibility and relatively calm or steady winds, but the purposefully limited response rate means they are not generally smooth in their responses to varying wind shear or gusting wind conditions – i.e., not able to compensate in all dimensions rapidly enough – to safely permit their use.
The first aircraft to be certified to CAT III standards, on 28 December 1968,[1] was the Sud Aviation Caravelle, followed by the Hawker-Siddeley HS.121 Trident in May 1972 (CAT IIIA) and to CAT IIIB during 1975. The Trident had been certified to CAT II on 7 February 1968. Besides providing automatic landing, automatic ground roll and extensive en route facilities, the Trident's AFCS (Automatic Flight Control System) also provided automatic overshoot (go-round) which was essential for Cat II operation, PVD (paravisual display) ground roll guidance for take-off in 100 metres runway visual range (RVR) and as back up to the ‘fail-soft’ automatic rudder control system during Cat. IIIB landings, and a Ground Run Monitor (GRM) for measuring ground speed and distance travelled as an aid for estimating runway turn-off points and taxying.[2]
Autoland capability has seen the most rapid adoption in areas and on aircraft that must frequently operate in very poor visibility. Airports troubled by fog on a regular basis are prime candidates for Category III approaches, and including autoland capability on jet airliners helps reduce the likelihood that they will be forced to divert by bad weather.[3]
Autoland is highly accurate. In his 1959 paper,[4] John Charnley, then Superintendent of the UK Royal Aircraft Establishment's (RAE) Blind Landing Experimental Unit (BLEU), concluded a discussion of statistical results by saying that "It is fair to claim, therefore, that not only will the automatic system land the aircraft when the weather prevents the human pilot, it also performs the operation much more precisely".
Previously, autoland systems have been so expensive that they were rarely used on small aircraft. However, as display technology has developed, the addition of a head up display (HUD) allows for a trained pilot to manually fly the aircraft using guidance cues from the flight guidance system. This significantly reduces the cost of operating in very low visibility, and allows aircraft that are not equipped for automatic landings to make a manual landing safely at lower levels of look ahead visibility or runway visual range (RVR). In 1989, Alaska Airlines was the first airline in the world to manually land a passenger-carrying jet (Boeing B727) in FAA Category III weather (dense fog) made possible with the head-up guidance system.[5][6]
Commercial aviation autoland was initially developed in the United Kingdom, as a result of the frequent occurrence of very low visibility conditions in winter in North-west Europe. These occur particularly when anticyclones are in place over central Europe in November/December/January when temperatures are low, and radiation fog easily forms in relatively stable air. The severity of this type of fog was exacerbated in the late 1940s and 1950s by the prevalence of carbon and other smoke particles in the air from coal burning heating and power generation.
Cities particularly affected included the main UK centers, and their airports such as London Heathrow, Gatwick, Manchester, Birmingham and Glasgow, as well as European cities such as Amsterdam, Brussels, Paris, Zurich and Milan. Visibility at these times could become as low as a few feet (hence the London fogs of movie fame) and when combined with the soot created lethal long-persistence smog. These conditions led to the passing of the UK's "Clean Air Act," which banned the burning of smoke-producing fuel.
During the immediate post-war period, British European Airways (BEA) suffered a number of accidents during approach and landing in poor visibility, which caused it to focus on the problems of how pilots could land safely in such conditions. A major breakthrough came with the recognition that in such low visibility the very limited visual information available (lights and so on) was extraordinarily easy to misinterpret, especially when the requirement to assess it was combined with a requirement to simultaneously fly the aircraft on instruments. This led to the development of what is now widely understood as the "monitored approach" procedure.
One pilot is assigned the task of accurate instrument flying while the other assesses the visual cues available at decision height, taking control to execute the landing once satisfied that the aircraft is in fact in the correct place and on a safe trajectory for a landing. The result was a major improvement in the safety of operations in low visibility, and as the concept clearly incorporates vast elements of what is now known as crew resource management (although predating this phrase by some three decades) it was expanded to encompass a far broader spectrum of operations than just low visibility.
However, associated with this "human factors" approach was a recognition that improved autopilots could play a major part in low-visibility landings. The components of all landings are the same, involving navigation from a point at altitude en route to a point where the wheels are on the desired runway. This navigation is accomplished using information from either external, physical, visual cues, or from synthetic cues such as flight instruments. At all times, there must be sufficient total information to ensure that the aircraft's position and trajectory (vertical and horizontal) are correct.
The problem with low visibility operations is that the visual cues may be reduced to effectively zero, and hence there is an increased reliance on "synthetic" information. The dilemma faced by BEA was to find a way to operate without cues, because this situation occurred on its network with far greater frequency than on that of any other airline. It was particularly prevalent at its home base, London Heathrow, which could effectively be closed for days at a time.
Development of autoland
The United Kingdom government's aviation research facilities including the Blind Landing Experimental Unit (BLEU) set up during 1945/46 at RAF Martlesham Heath and RAF Woodbridge to research all the relevant factors. BEA's flight technical personnel were heavily involved in BLEU's activities in the development of Autoland for its Trident fleet from the late 1950s. The work included analysis of fog structures, human perception, instrument design, and lighting cues amongst many others. After further accidents, this work also led to the development of aircraft operating minima in the form we know them today. In particular, it led to the requirement that a minimum visibility must be reported as available before the aircraft may commence an approach – a concept that had not existed previously. The basic concept of a "target level of safety" (10^-7) and of the analysis of "fault trees" to determine probability of failure events stemmed from about this period.
The basic concept of autoland flows from the fact that an autopilot could be set up to track an artificial signal such as an Instrument Landing System (ILS) beam more accurately than a human pilot could – not least because of the inadequacies of the electro-mechanical flight instruments of the time. If the ILS beam could be tracked to a lower height then clearly the aircraft would be nearer to the runway when it reached the limit of ILS usability, and nearer to the runway less visibility would be required to see sufficient cues to confirm the aircraft position and trajectory. With an angular signal system such as ILS, as altitude decreases all tolerances must be decreased – in both the aircraft system and the input signal – to maintain the required degree of safety.
This is because certain other factors – physical and physiological laws which govern for example the pilot's ability to make the aircraft respond – remain constant. For example, at 300 feet above the runway on a standard 3 degree approach the aircraft will be 6000 feet from the touchdown point, and at 100 feet it will be 2000 feet out. If a small course correction needs 10 seconds to be effected at 180kts it will take 3000ft. It will be possible if initiated at 300 feet of height, but not at 100 feet. Consequently, only a smaller course correction can be tolerated at the lower height, and the system needs to be more accurate.
This imposes a requirement for the ground-based, guidance element to conform to specific standards, as well as the airborne elements. Thus, while an aircraft may be equipped with an autoland system, it will be totally unusable without the appropriate ground environment. Similarly, it requires a crew trained in all aspects of the operation to recognize potential failures in both airborne and ground equipment, and to react appropriately, to be able to use the system in the circumstances from which it is intended. Consequently, the low visibility operations categories (Cat I, Cat II and Cat III) apply to all 3 elements in the landing – the aircraft equipment, the ground environment, and the crew. The result of all this is to create a spectrum of low visibility equipment, in which an aircraft's autoland autopilot is just one component.
The development of these systems proceeded by recognizing that although the ILS would be the source of the guidance, the ILS itself contains lateral and vertical elements that have rather different characteristics. In particular, the vertical element (glideslope) originates from the projected touchdown point of the approach, i.e. typically 1000ft from the beginning of the runway, while the lateral element (localizer) originates from beyond the far end. The transmitted glideslope therefore becomes irrelevant soon after the aircraft has reached the runway threshold, and in fact the aircraft has of course to enter its landing mode and reduce its vertical velocity quite a long time before it passes the glideslope transmitter. The inaccuracies in the basic ILS could be seen in that it was suitable for use down to 200ft. only (Cat I), and similarly no autopilot was suitable for or approved for use below this height.
The lateral guidance from the ILS localizer would however be usable right to the end of the landing roll, and hence is used to feed the rudder channel of the autopilot after touchdown. As aircraft approached the transmitter its speed is obviously reducing and rudder effectiveness diminishes, compensating to some extent for the increased sensitivity of the transmitted signal. More significantly however it means the safety of the aircraft is still dependent on the ILS during rollout. Furthermore, as it taxis off the runway and down any parallel taxiway, it itself acts a reflector and can interfere with the localizer signal. This means that it can affect the safety of any following aircraft still using the localizer. As a result, such aircraft cannot be allowed to rely on that signal until the first aircraft is well clear of the runway and the "Cat. 3 protected area".
The result is that when these low visibility operations are taking place, operations on the ground affect operations in the air much more than in good visibility, when pilots can see what is happening. At very busy airports, this results in restrictions in movement which can in turn severely impact the airport's capacity. In short, very low visibility operations such as autoland can only be conducted when aircraft, crews, ground equipment and air and ground traffic control all comply with more stringent requirements than normal.
The first "commercial development" automatic landings (as opposed to pure experimentation) were achieved through realizing that the vertical and lateral paths had different rules. Although the localizer signal would be present throughout the landing, the glide slope had to be disregarded before touchdown in any event. It was recognized that if the aircraft had arrived at decision height (200ft) on a correct, stable approach path – a prerequisite for a safe landing – it would have momentum along that path. Consequently, the autoland system could discard the glideslope information when it became unreliable (i.e. at 200ft), and use of pitch information derived from the last several seconds of flight would ensure to the required degree of reliability that the descent rate (and hence adherence to the correct profile) would remain constant. This "ballistic" phase would end at the height when it became necessary to increase pitch and reduce power to enter the landing flare. The pitch change occurs over the runway in the 1000 horizontal feet between the threshold and the glide slope antenna, and so can be accurately triggered by radio altimeter.
Autoland was first developed in BLEU and RAF aircraft such as the English Electric Canberra, Vickers Varsity and Avro Vulcan, and later for BEA's Trident fleet, which entered service in the early 1960s. The Trident was a 3-engined jet built by de Havilland with a similar configuration to the Boeing 727, and was extremely sophisticated for its time. BEA had specified a "zero-visibility" capability for it to deal with the problems of its fog-prone network. It had an autopilot designed to provide the necessary redundancy to tolerate failures during autoland, and it was this design which had triple redundancy.
This autopilot used three simultaneous processing channels each giving a physical output. The fail-safe element was provided by a "voting" procedure using torque switches, whereby it was accepted that in the event that one channel differed from the other two, the probability of two similar simultaneous failures could be discounted and the two channels in agreement would "out-vote" and disconnect the third channel. However, this triple-voting system is by no means the only way to achieve adequate redundancy and reliability, and in fact soon after BEA and de Havilland had decided to go down that route, a parallel trial was set up using a "dual-dual" concept, chosen by BOAC and Vickers for the VC10 4-engined long range aircraft. This concept was later used on the Concorde. Some BAC 1-11 aircraft used by BEA also had a similar system.
The earliest experimental autopilot-controlled landings in commercial service were not in fact full auto landings but were termed "auto-flare". In this mode, the pilot controlled the roll and yaw axes manually while the autopilot controlled the "flare" or pitch. These were often done in passenger service as part of the development program. The Trident's autopilot had separate engagement switches for the pitch and roll components, and although the normal autopilot disengagement was by means of a conventional control yoke thumb-button, it was also possible to disengage the roll channel while leaving the pitch channel engaged.
In these operations the pilot had acquired full visual reference, normally well above decision height, but instead of fully disengaging the autopilot with the thumb-button, called for the second officer to latch off the roll channel only. The second officer then controlled the lateral flight path manually while monitoring the autopilot's continued control of the vertical flight path – ready to completely disengage it at the first sign of any deviation. While this sounds as if it may add a risk element in practice it is of course no different in principle to a training pilot monitoring a trainee's handling during on-line training or qualification.
Having proven the reliability and accuracy of the autopilot's ability to safely flare the aircraft, the next elements were to add in similar control of the thrust. This was done by a radio altimeter signal which drove the autothrottleservos to a flight idle setting. As the accuracy and reliability of the ground based ILS localiser was increased on a step by step basis, it was permissible to leave the roll channel engaged longer and longer, until in fact the aircraft had ceased to be airborne, and a fully automatic landing had in fact been completed. The first such landing in a BEA Trident was achieved at RAE Bedford (by then home of BLEU) in March 1964. The first on a commercial flight with passengers aboard was achieved on flight BE 343 on 10 June 1965, with a Trident 1 G-ARPR, from Paris to Heathrow with Captains Eric Poole and Frank Ormonroyd.
The Lockheed L-1011 TriStar had its autoland functionality placed in key roles during its marketing.
Subsequently, autoland systems became available on a number of aircraft types but the primary customers were those mainly European airlines whose networks were severely affected by radiation fog. Early autoland systems needed a relatively stable air mass and could not operate in conditions of turbulence and in particular gusty crosswinds. In North America, it was generally the case that reduced but not zero visibility was often associated with these conditions, and if the visibility really became almost zero in, for example, blowing snow or other precipitation then operations would be impossible for other reasons.
As a result, neither airlines nor airports placed a high priority on operations in the lowest visibility. The provision of the necessary ground equipment (ILS) and associated systems for Category 3 operations was almost non existent and the major manufacturers did not regard it as a basic necessity for new aircraft. In general, during the 1970s and 1980s, it was available if a customer wanted it, but at such a high price (due to being a reduced production run item) that few airlines could see a cost justification for it.
This led to the absurd situation for British Airways that as the launch customer for the Boeing 757 to replace the Trident, the brand-new "advanced" aircraft had inferior all weather operations capability compared to the fleet being broken up for scrap. An indication of this philosophical divide is the comment from a senior Boeing vice president that he could not understand why British Airways were so concerned about the Category 3 certification, as there were only at that time two or three suitable runways in North America on which it could be fully used. It was pointed out that British Airways had 12 such runways on its domestic network alone, four of them at its main base at Heathrow.
In the 1980s and 1990s, there was increasing pressure globally from customer airlines for at least some improvements in low visibility operations; both for flight regularity and from safety considerations. At the same time, it became evident that the requirement for a true zero-visibility operation (as originally envisaged in the ICAO Category definitions) had diminished, as clean-air laws had reduced the adverse effect of smoke adding to radiation fog in the worst affected areas. Improved avionics meant that the technology became cheaper to implement, and manufacturers raised the standard of the "basic" autopilot accuracy and reliability. The result was that on the whole the larger new airliners were now able to absorb the costs of at least Category 2 autoland systems into their basic configuration.
Simultaneously, pilot organizations globally were advocating the use of Head Up Display systems primarily from a safety viewpoint. Many operators in non-sophisticated environments without many ILS equipped runways were also looking for improvements. The net effect was pressure within the industry to find alternative ways to achieve low visibility operations, such as a "hybrid" system which used a relatively low reliability autoland system monitored by the pilots via a HUD. Alaska Airlines was a leader in this approach and undertook a lot of development work with Flight Dynamics and Boeing in this respect.
A major problem with this approach was that European authorities were very reluctant to certificate such schemes as they undermined the well-proven concepts of "pure" autoland systems. This impasse was broken when British Airways became involved as a potential customer for Bombardier's Regional Jet, which could not accommodate a full Cat 3 autoland system, but would be required to operate in those conditions. By working with Alaska Airlines and Boeing, British Airways technical pilots were able to demonstrate that a hybrid concept was feasible, and although British Airways never eventually bought the regional jet, this was the breakthrough needed for international approval for such systems which meant that they could reach a global market.
The wheel turned full circle in December 2006 when London Heathrow was affected for a long period by dense fog. This airport was operating at maximum capacity in good conditions, and the imposition of low visibility procedures required to protect the localizer signal for autoland systems meant a major reduction in capacity from approximately 60 to 30 landings per hour. Since most airlines operating into Heathrow already had autoland-equipped aircraft, and thus expected to operate as normal, massive delays occurred. The worst affected airline was of course British Airways, as the largest operator at the airport.
Emergency autoland
Garmin Aviation started studying an emergency autoland feature in 2001 and launched the program in 2010 with more than 100 employees, investing around $20 million. Flight tests began in 2014 with 329 test landings completed in a Cessna 400 Corvalis and another 300 landings in other aircraft. The feature is activated by a guarded red button on Garmin G3000 avionics, evaluating winds, weather and fuel reserves to select a suitable diversion airport and taking over the aircraft controls to land, it advises ATC and displays instructions to occupants.[7]
A Piper M600 single-engine turboprop aircraft began flight tests in early 2018 and completed more than 170 landings to seek pending FAA certification, which it achieved in 2020. Providing access to more than 9,000 runways over 4,500ft (1,400m), it is offered from 2020 for $170,000 including extra equipment. It was also certified for the single-engine Cirrus Vision SF50 jet that same year, landing on runways over 5,836ft (1,779m), the SOCATA-Daher TBM 900, and will eventually be certified on other aircraft.[7]
In June 2021, the Garmin Autoland system won the 2020 Collier Trophy, for "the greatest achievement in aeronautics or astronautics in America" during the preceding year.[8]
A typical autoland system consists of an ILS (integrated glideslope receiver, localizer receiver, and perhaps GPS receiver as well) radio to receive the localizer and glideslope signals. The output of this radio will be a deviation from center which is provided to the flight control computer; this computer controls the aircraft control surfaces to maintain the aircraft centered on the localizer and glideslope. The flight control computer also controls the aircraft throttles to maintain the appropriate approach speed. At the appropriate height above the ground (as indicated by the radio altimeter) the flight control computer will retard the throttles and initiate a pitch-up maneuver. The purpose of this "flare" is to reduce the energy of the aircraft, reducing lift and allowing it to settle onto the runway.
For CAT IIIc, the flight control computer will continue to accept deviations from the localizer and use the rudder to maintain the aircraft on the localizer (which is aligned with the runway centerline.) On landing the spoilers will deploy (these are surfaces on the top of the wing towards the trailing edge) which causes airflow over the wing to become turbulent, destroying lift. At the same time the autobrake system will apply the brakes. The anti-skid system will modulate brake pressure to keep all wheels turning. As the speed decreases, the rudder will lose effectiveness and the pilot will need to control the direction of the airplane using nose wheel steering, a system which typically is not connected to the flight control computer.
From an avionics safety perspective, a CAT IIIc landing is the worst-case scenario for safety analysis because a failure of the automatic systems from flare through the roll-out could easily result in a "hard over" (where a control surface deflects fully in one direction.) This would happen so fast that the flight crew may not effectively respond. For this reason autoland systems are designed to incorporate a high degree of redundancy so that a single failure of any part of the system can be tolerated (fail active) and a second failure can be detected – at which point the autoland system will turn itself off (uncouple, fail passive).
One way of accomplishing this is to have "three of everything." Three ILS receivers, three radio altimeters, three flight control computers, and three ways of controlling the flight surfaces. The three flight control computers all work in parallel and are in constant cross communications, comparing their inputs (ILS receivers and radio altimeters) with those of the other two flight control computers. If there is a difference in inputs, then a computer can "vote out" the deviant input and will notify the other computers that (for instance) "RA1 is faulty." If the outputs don't match, a computer can declare itself as faulty and, if possible, take itself off line.
When the pilot arms the system (prior to capture of either the localizer or glideslope) the flight control computers perform an extensive series of built-in tests. For a CAT III landing, all the sensors and all the flight computers must be in good health before the pilot receives an "AUTOLAND ARM" indication (generic indications that will vary depending on equipment supplier and aircraft manufacturer). If part of the system is in error, then an indication such as "APPROACH ONLY" would be presented to inform the flight crew that a CAT III landing is not possible.
If the system is properly in the ARM mode, when the ILS receiver detects the localizer, then the autoland system mode will change to "LOCALIZER CAPTURE". The flight control computer will turn the aircraft into the localizer and fly along the localizer. A typical approach will have the aircraft come in "below the glideslope" (vertical guidance) so the airplane will fly along the localizer (aligned to the runway centerline) until the glideslope is detected. At this point the autoland mode will change to CAT III and the aircraft will be flown by the flight control computer along the localizer and glideslope beams.
The antennas for these systems are not at the runway touch down point, with the localizer being some distance beyond the runway. At a predefined distance above the ground the aircraft will initiate the flare maneuver, maintain the same heading, and settle onto the runway within the designated touch down zone.
If the autoland system loses redundancy prior to the decision height, then an "AUTOLAND FAULT" error message will be displayed to the flight crew at which point the crew can elect to continue as a CAT II approach or if this is not possible because of weather conditions, then the crew would need to initiate a go-around and proceed to an alternative airport.
If a single failure occurs below decision height, "AUTOLAND FAULT" will be displayed; at that point the aircraft is committed to landing and the autoland system will remain engaged, controlling the aircraft on only two systems until the pilot completes the rollout and brings the aircraft to a full stop on the runway or turns off the runway onto a taxiway. This is termed "fail-active." In this state the autoland system is "one fault away" from disengaging so the "AUTOLAND FAULT" indication should inform the flight crew to monitor the system behavior very carefully and be ready to take control immediately.
The system is still fail-active and is still performing all necessary cross-checks so that if one of the flight control computers decides that the right thing to do is order a full deflection of a control surface, the other computer will detect that there is a difference in the commands and this will take both computers off line (fail-passive) at which time the flight crew must immediately take control of the aircraft as the automatic systems have done the safe thing by taking themselves off line.
During system design, the predicted reliability numbers for the individual equipment which makes up the entire autoland system (sensors, computers, controls, and so forth) are combined and an overall probability of failure is calculated. As the threat exists primarily during the flare through roll-out, this exposure time is used and the overall failure probability must be less than one in a million.[9]
In aviation, instrument flight rules (IFR) is one of two sets of regulations governing all aspects of civil aviation aircraft operations; the other is visual flight rules (VFR).
In aviation, the instrument landing system (ILS) is a precision radio navigation system that provides short-range guidance to aircraft to allow them to approach a runway at night or in bad weather. In its original form, it allows an aircraft to approach until it is 200 feet (61 m) over the ground, within a 1⁄2 mile (800 m) of the runway. At that point the runway should be visible to the pilot; if it is not, they perform a missed approach. Bringing the aircraft this close to the runway dramatically increases the range of weather conditions in which a safe landing can be made. Other versions of the system, or "categories", have further reduced the minimum altitudes, runway visual ranges (RVRs), and transmitter and monitoring configurations designed depending on the normal expected weather patterns and airport safety requirements.
An autopilot is a system used to control the path of an aircraft, marine craft or spacecraft without requiring constant manual control by a human operator. Autopilots do not replace human operators. Instead, the autopilot assists the operator's control of the vehicle, allowing the operator to focus on broader aspects of operations.
Luxair Flight 9642 (LG9642/LGL9642) was a scheduled international passenger flight from Berlin Tempelhof Airport, Germany, to Luxembourg Findel Airport, Luxembourg, operated by Luxembourg national airline Luxair. On 6 November 2002, the aircraft operating the flight, a Fokker 50 registered as LX-LGB, lost control and crashed onto a field during an attempted landing at the airport. Out of 22 passengers and crew members on board, only two people survived. The crash is the deadliest aviation disaster to occur in Luxembourg.
A precision approach path indicator (PAPI) is a system of lights on the side of an airport runway threshold that provides visual descent guidance information during final approach. It is generally located on the left-hand side of the runway approximately 300 meters beyond the landing threshold of the runway.
In aviation, a critical area refers to a designated area of an airport that all aircraft, vehicles, persons or physical obstructions must remain clear of when one or more Instrument Landing Systems (ILS) are in use, to protect against signal interference or attenuation that may lead to navigation errors, or accident. Critical areas also protect the ILS system's internal monitoring.
In aviation, an instrument approach or instrument approach procedure (IAP) is a series of predetermined maneuvers for the orderly transfer of an aircraft operating under instrument flight rules from the beginning of the initial approach to a landing, or to a point from which a landing may be made visually. These approaches are approved in the European Union by EASA and the respective country authorities and in the United States by the FAA or the United States Department of Defense for the military. The ICAO defines an instrument approach as "a series of predetermined maneuvers by reference to flight instruments with specific protection from obstacles from the initial approach fix, or where applicable, from the beginning of a defined arrival route to a point from which a landing can be completed and thereafter, if landing is not completed, to a position at which holding or en route obstacle clearance criteria apply."
A takeoff/go-around switch is a switch on the autothrottle of modern large aircraft, with two modes: takeoff (TO) and go-around (GA). The mode is dependent on the phase of flight; usually, on approach to land, the autopilot will be set to approach mode, therefore if the TO/GA switch is pressed it will activate the go-around mode of the autothrottle (about 90–92% N1, if pressed again, go around thrust will increase to full ; conversely, when takeoff is set on the autopilot, the switch activates takeoff mode of the autothrottle. On Boeing aircraft TO/GA modes are selected by a separate button near the throttle levers, but on Airbus aircraft it is activated by advancing the thrust levers forward to the TO/GA detent.
Britannia Airways Flight 226A was an international passenger flight from Cardiff, Wales to Girona, Spain, operated by charter airliner Britannia Airways. On 14 September 1999, the Boeing 757-204 aircraft suffered a crash landing and broke apart during a thunderstorm in Girona-Costa Brava Airport. Of the 236 passengers and nine crew on board, two were seriously injured and 41 sustained minor injuries. One of the passengers who had apparently sustained only minor injuries died five days later of unsuspected internal injuries. The aircraft involved in the crash, Boeing 757-204 registration G-BYAG, was damaged beyond economical repair and scrapped.
Japan Air Lines Flight 2 was a scheduled passenger flight on November 22, 1968. The plane was a new Douglas DC-8-62 named Shiga (志賀), flying from Tokyo International Airport (Haneda) to San Francisco International Airport (SFO). Due to heavy fog and other factors, Captain Kohei Asoh mistakenly ditched the plane near Coyote Point in the shallow waters of San Francisco Bay, two and a half miles short of the runway. All 107 people on board survived the accident without any injuries.
Turkish Airlines Flight 634 was a scheduled domestic passenger flight from Turkish Airlines' hub at Istanbul Atatürk Airport to Diyarbakır Airport in southeastern Turkey. On 8 January 2003 at 20:19 EET, the aircraft operating the flight, a British Aerospace Avro RJ100, struck the ground on final approach approximately 900 metres (3,000 ft) short of the runway threshold during inclement weather conditions. In the following collision with a slope, a post-crash fire broke out, killing 75 of the 80 occupants, including the entire crew. This is the deadliest aviation accident to involve the BAe 146.
Aviastar-TU Flight 1906 was a Tupolev Tu-204 that crashed while attempting to land at Domodedovo International Airport, Moscow, Russia, in heavy fog on 22 March 2010. The aircraft was on a ferry flight from Hurghada International Airport, Egypt to Moscow, and had no passengers on board; all eight crew survived the accident, four with serious injuries requiring hospitalization and four with minor injuries. The accident was the first hull loss of a Tu-204 and the first hull loss for Aviastar-TU.
Henan Airlines Flight 8387 was a domestic flight operated by Henan Airlines from Harbin to Yichun, China. On the night of 24 August 2010, the Embraer E190 operating the route crashed on approach to Yichun Lindu Airport in fog. Forty-four of the ninety-six people on board were killed. It was the first hull loss and the first fatal accident involving the Embraer E190.
First Air Flight 6560 was a domestic charter flight that crashed on landing at Resolute, Nunavut, Canada, on 20 August 2011. Of the 15 people on board, 12 were killed and the remaining three were severely injured. The Boeing 737-200 of First Air was operating a service from Yellowknife, Northwest Territories, when it struck a hill in cloud near Resolute Bay Airport.
The Blind Landing Experimental Unit, abbreviated BLEU, was a unit of the British government tasked with creating an early autolanding system for military and civilian aircraft from the late 1940s until the mid-1960s.
Asiana Airlines Flight 162 was a regular short-haul international passenger flight from Incheon International Airport near Seoul, South Korea, to Hiroshima Airport in Hiroshima, Japan. On 14 April 2015, the Airbus A320-232 aircraft touched down short of the runway, struck the localizer array, skidded onto the runway on its tail, and spun 120 degrees before finally coming to a rest on the grass, opposite the terminal building. The aircraft suffered substantial damage to the left wing and engine. Of the 82 people aboard, 27 were injured, one seriously.
Delta Air Lines Flight 723 was a flight operated by a McDonnell Douglas DC-9 twin-engine jetliner, operating as a scheduled domestic passenger flight from Burlington, Vermont, to Logan International Airport in Boston, Massachusetts, with an intermediate stop in Manchester, New Hampshire. On July 31, 1973, at 11:08a.m., while on an instrument landing system (ILS) instrument approach into Logan in low clouds and fog, the aircraft descended below the glidepath, struck a seawall, and crashed. 88 of the 89 occupants aboard were killed.
Turkish Airlines Flight 6491 was a scheduled international cargo flight operated by ACT Airlines on behalf of Turkish Cargo, from Hong Kong to Istanbul via Bishkek, Kyrgyzstan. On 16 January 2017, the Boeing 747-400F flying the route crashed in a residential area while attempting to land in thick fog at Manas International Airport, Bishkek. A total of 39 people – all four crew members on board and 35 residents on the ground – were killed.
Brit Air Flight 5672 (AF5672) was a domestic passenger flight from Nantes Atlantique Airport to Brest-Guipavas Airport, France, which crashed on 22 June 2003. The flight was a Bombardier CRJ100ER operated by Brit Air, a regional airline which was a subsidiary of Air France. The aircraft crashed during its landing phase, striking multiple obstacles and then crashing onto a road and bursting into flames. The occupants were evacuated immediately. The captain was killed in the crash, while 23 survived. The crash was dubbed a miracle flight, as almost all of the occupants survived the crash. The media called the event the "Miracle in Brest".
CommutAir Flight 4933 was a domestic regional flight operating from Newark, New Jersey, to Presque Isle, Maine, in the United States. The flight was operated by CommutAir under the United Express brand. On March 4, 2019, the Embraer EMB-145XR operating the flight touched down in a snow-covered grassy area to the right of the runway at Presque Isle International Airport, injuring three aircraft occupants and substantially damaging the aircraft. The accident was attributed to confirmation bias which prompted the flight crew to continue descending even though they could not see the runway due to snow; poor decision-making by the captain, fatigue of the first officer, and problems with the airport's instrument landing system were identified as contributing factors.
This page is based on this Wikipedia article Text is available under the CC BY-SA 4.0 license; additional terms may apply. Images, videos and audio are available under their respective licenses.
