Carbon black

Last updated
Carbon black
Carbon black.jpg
Names
Other names
  • Acetylene black
  • Channel black
  • Furnace black
  • Lamp black
  • Thermal black
  • C.I. Pigment Black 6
Identifiers
3D model (JSmol)
ECHA InfoCard 100.014.191 OOjs UI icon edit-ltr-progressive.svg
EC Number
  • 215-609-9
E number E152 (colours)
UNII
  • C
Properties
C
Molar mass 12.011 g·mol−1
AppearanceBlack solid
Density 1.8–2.1 g/cm3 (20 °C) [1]
Practically insoluble [1]
Hazards
Lethal dose or concentration (LD, LC):
> 15400 mg/kg (oral rat) [1]
3000 mg/kg (dermal, rabbit) [1]
Except where otherwise noted, data are given for materials in their standard state (at 25 °C [77 °F], 100 kPa).
Worker at carbon black plant, 1942 Worker at carbon black plant2.jpg
Worker at carbon black plant, 1942

Carbon black (with subtypes acetylene black, channel black, furnace black, lamp black and thermal black) is a material produced by the incomplete combustion of coal tar, vegetable matter, or petroleum products, including fuel oil, fluid catalytic cracking tar, and ethylene cracking in a limited supply of air. Carbon black is a form of paracrystalline carbon that has a high surface-area-to-volume ratio, albeit lower than that of activated carbon. It is dissimilar to soot in its much higher surface-area-to-volume ratio and significantly lower (negligible and non-bioavailable) polycyclic aromatic hydrocarbon (PAH) content. However, carbon black can be used as a model compound for diesel soot to better understand how diesel soot behaves under various reaction conditions as carbon black and diesel soot have some similar properties such as particle sizes, densities, and copolymer adsorption abilities that contribute to them having similar behaviours under various reactions such as oxidation experiments. [2] [3] [ better source needed ] Carbon black is used as a colorant and reinforcing filler in tires and other rubber products; pigment and wear protection additive in plastics, paints, and ink pigment. [4] It is used in the EU as a food colorant when produced from vegetable matter (E153).

Contents

The current International Agency for Research on Cancer (IARC) evaluation is that, "Carbon black is possibly carcinogenic to humans (Group 2B)". [5] Short-term exposure to high concentrations of carbon black dust may produce discomfort to the upper respiratory tract through mechanical irritation.

Common uses

The most common use (70%) of carbon black is as a pigment and reinforcing phase in automobile tires. Carbon black also helps conduct heat away from the tread and belt area of the tire, reducing thermal damage and increasing tire life. Its low cost makes it a common addition to cathodes and anodes and is considered a safe replacement to lithium metal in lithium-ion batteries. [6] About 20% of world production goes into belts, hoses, and other non-tire rubber goods. The remaining 10% use of carbon black comes from pigment in inks, coatings, and plastics, as well as being used as a conductive additive in lithium-ion batteries. [7]

Carbon black is added to polypropylene because it absorbs ultraviolet radiation, which otherwise causes the material to degrade. Carbon black particles are also employed in some radar absorbent materials, in photocopier and laser printer toner, and in other inks and paints. The high tinting strength and stability of carbon black has also provided use in coloring of resins and films. [8] Carbon black has been used in various applications for electronics. A good conductor of electricity, carbon black is used as a filler mixed in plastics, elastomer, films, adhesives, and paints. [8] It is used as an antistatic additive agent in automobile fuel caps and pipes.

Carbon black from vegetable origin is used as a food coloring, known in Europe as additive E153. It is approved for use as additive 153 (Carbon blacks or Vegetable carbon) in Australia and New Zealand [9] but has been banned in the US. [10] The color pigment carbon black has been widely used for many years in food and beverage packaging. It is used in multi-layer UHT milk bottles in the US, parts of Europe and Asia, and South Africa, and in items like microwavable meal trays and meat trays in New Zealand.

The Canadian Government's extensive review of carbon black in 2011 concluded that carbon black could continue to be used in products – including food packaging for consumers – in Canada. This was because "in most consumer products carbon black is bound in a matrix and unavailable for exposure, for example as a pigment in plastics and rubbers" and "it is proposed that carbon black is not entering the environment in a quantity or concentrations or under conditions that constitute or may constitute a danger in Canada to human life or health." [11]

Within Australasia, the color pigment carbon black in packaging must comply with the requirements of either the EU or US packaging regulations. If any colorant is used, it must meet European partial agreement AP(89)1. [12]

Total production was around 8,100,000 metric tons (8,900,000 short tons) in 2006. [13] Global consumption of carbon black, estimated at 13.2 million metric tons, valued at US$13.7 billion, in 2015, is expected to reach 13.9 million metric tons, valued at US$14.4 billion in 2016.

Global consumption is forecast to maintain a CAGR (compound annual growth rate) of 5.6% between 2016 and 2022, reaching 19.2 million metric tons, valued at US$20.4 billion, by 2022. [14]

Reinforcing carbon blacks

The highest volume use of carbon black is as a reinforcing filler in rubber products, especially tires. While a pure gum vulcanization of styrene-butadiene has a tensile strength of no more than 2 MPa and negligible abrasion resistance, compounding it with 50% carbon black by weight improves its tensile strength and wear resistance as shown in the table below. It is used often in the aerospace industry in elastomers for aircraft vibration control components such as engine mounts.

Certain types of carbon black used in tires, plastics and paints
NameAbbrev.ASTM
desig.		Particle
Size
nm		Tensile
strength
MPa		Relative
laboratory
abrasion		Relative
roadwear
abrasion
Super Abrasion FurnaceSAFN11020–2525.21.351.25
Intermediate SAFISAFN22024–3323.11.251.15
High Abrasion FurnaceHAFN33028–3622.41.001.00
Easy Processing ChannelEPCN30030–3521.70.800.90
Fast Extruding FurnaceFEFN55039–5518.20.640.72
High Modulus FurnaceHMFN66049–7316.10.560.66
Semi-Reinforcing FurnaceSRFN77070–9614.70.480.60
Fine ThermalFTN880180–20012.60.22–
Medium ThermalMTN990250–3509.80.18–

Practically all rubber products where tensile and abrasion wear properties are important use carbon black, so they are black in color. Where physical properties are important but colors other than black are desired, such as white tennis shoes, precipitated or fumed silica has been substituted for carbon black. Silica-based fillers are also gaining market share in automotive tires because they provide better trade-off for fuel efficiency and wet handling due to a lower rolling loss. Traditionally silica fillers had worse abrasion wear properties, but the technology has gradually improved to a point where they can match carbon black abrasion performance.

Pigment

Carbon black (Color Index International, PBK-7) is the name of a common black pigment, traditionally produced from charring organic materials such as wood or bone. It appears black because it reflects very little light in the visible part of the spectrum, with an albedo near zero. The actual albedo varies depending on the source material and method of production. It is known by a variety of names, each of which reflects a traditional method for producing carbon black:

All of these types of carbon black were used extensively as paint pigments since prehistoric times. [15] Rembrandt, Vermeer, Van Dyck, and more recently, Cézanne, Picasso and Manet [16] employed carbon black pigments in their paintings. A typical example is Manet's "Music in the Tuileries", [17] where the black dresses and the men's hats are painted in ivory black. [18]

Newer methods of producing carbon black have largely superseded these traditional sources.[ citation needed ] For artisanal purposes, carbon black produced by any means remains common. [8]

Surface and surface chemistry

All carbon blacks have chemisorbed oxygen complexes (i.e., carboxylic, quinonic, lactonic, phenolic groups and others) on their surfaces to varying degrees depending on the conditions of manufacture. [19] These surface oxygen groups are collectively referred to as volatile content. It is also known to be a non-conductive material due to its volatile content.

The coatings and inks industries prefer grades of carbon black that are acid-oxidized. Acid is sprayed in high-temperature dryers during the manufacturing process to change the inherent surface chemistry of the black. The amount of chemically-bonded oxygen on the surface area of the black is increased to enhance performance characteristics.

Use in lithium-ion batteries

The generic structure of carbon black. Carbon Black Structure.png
The generic structure of carbon black.

Carbon black is a common conductive additive for lithium ion batteries as they have small particle sizes and large specific surface areas (SSA) which allow for the additive to be well distributed throughout the cathode or anode in addition to being cheap and long-lasting. [7] [20] Unlike graphite, which is one of the other common materials used in chargeable batteries, carbon black consists of crystal lattices that are further apart and promotes Li+ intercalation because it allows more pathways for lithium storage. [20]

Carbon black has a low density that allows for a large volume of it to be dispersed so that its conductive effects are applied evenly throughout the battery. [21] [22] Furthermore, its arrangement of randomly distributed graphite-like crystals improves battery stability because of the decrease in the potential barrier of lithium intercalation into graphite, which ultimately affects the performance of cathodes. [20]

While carbon black is lightweight and well dispersed throughout the battery and increases the conductive performance of batteries, it also contains oxygen containing hydrophilic functional groups that can cause side reactions to occur in the battery and lead to the decomposition of electrolyte. Graphitization (heating) of carbon black can thermally decompose the hydrophilic functional groups and thus increase the cycle life of the battery which maintains the conductive abilities of carbon black while mitigating the damage that can be caused to batteries by hydrophilic functional groups.

Half cells created with heavy graphitization, light graphitization, and no graphitization showed that the cell created with heavy graphitization had a stable cycle life of 320 cycles, the cell with light graphitization showed a stable cycle life of 200 cycles, and the cell with no graphitization showed a stable cycle life of 160 cycles. [7]

Safety

Carcinogenicity

Carbon black is considered possibly carcinogenic to humans and classified as a Group 2B carcinogen because there is sufficient evidence in experimental animals with inadequate evidence in human epidemiological studies. [5] The evidence of carcinogenicity in animal studies comes from two chronic inhalation studies and two intratracheal instillation studies in rats, which showed significantly elevated rates of lung cancer in exposed animals. [5] An inhalation study on mice did not show significantly elevated rates of lung cancer in exposed animals. [5] Epidemiologic data comes from three cohort studies of carbon black production workers. Two studies, from the United Kingdom and Germany, with over 1,000 workers in each study group showed elevated mortality from lung cancer. [5] A third study of over 5,000 carbon black workers in the United States did not show elevated mortality. [5] Newer findings of increased lung cancer mortality in an update from the UK study suggest that carbon black could be a late-stage carcinogen. [23] [24] However, a more recent and larger study from Germany did not confirm this hypothesis. [25]

Occupational safety

There are strict guidelines available and in place to ensure employees who manufacture carbon black are not at risk of inhaling unsafe doses of carbon black in its raw form. [26] Respiratory personal protective equipment is recommended to properly protect workers from inhalation of carbon black. The recommended type of respiratory protection varies depending on the concentration of carbon black used. [27]

People can be exposed to carbon black in the workplace by inhalation and contact with the skin or eyes. The Occupational Safety and Health Administration (OSHA) has set the legal limit (Permissible exposure limit) for carbon black exposure in the workplace at 3.5 mg/m3 over an 8-hour workday. The National Institute for Occupational Safety and Health (NIOSH) has set a Recommended exposure limit (REL) of 3.5 mg/m3 over an 8-hour workday. At levels of 1750 mg/m3, carbon black is immediately dangerous to life and health. [28]

See also

Related Research Articles

<span class="mw-page-title-main">Electrode</span> Electrical conductor used to make contact with nonmetallic parts of a circuit

An electrode is an electrical conductor used to make contact with a nonmetallic part of a circuit. Electrodes are essential parts of batteries that can consist of a variety of materials depending on the type of battery.

<span class="mw-page-title-main">Graphite</span> Allotrope of carbon, mineral, substance

Graphite is a crystalline form of the element carbon. It consists of stacked layers of graphene. Graphite occurs naturally and is the most stable form of carbon under standard conditions. Synthetic and natural graphite are consumed on a large scale for uses in pencils, lubricants, and electrodes. Under high pressures and temperatures it converts to diamond. It is a good conductor of both heat and electricity.

<span class="mw-page-title-main">Talc</span> Hydrated magnesium phyllosilicate mineral

Talc, or talcum, is a clay mineral composed of hydrated magnesium silicate, with the chemical formula Mg3Si4O10(OH)2. Talc in powdered form, often combined with corn starch, is used as baby powder. This mineral is used as a thickening agent and lubricant. It is an ingredient in ceramics, paints, and roofing material. It is a main ingredient in many cosmetics. It occurs as foliated to fibrous masses, and in an exceptionally rare crystal form. It has a perfect basal cleavage and an uneven flat fracture, and it is foliated with a two-dimensional platy form.

<span class="mw-page-title-main">Lithium-ion battery</span> Rechargeable battery type

A lithium-ion or Li-ion battery is a type of rechargeable battery that uses the reversible intercalation of Li+ ions into electronically conducting solids to store energy. In comparison with other commercial rechargeable batteries, Li-ion batteries are characterized by higher specific energy, higher energy density, higher energy efficiency, a longer cycle life, and a longer calendar life. Also noteworthy is a dramatic improvement in lithium-ion battery properties after their market introduction in 1991: within the next 30 years, their volumetric energy density increased threefold while their cost dropped tenfold.

<span class="mw-page-title-main">Diesel exhaust</span> Gaseous exhaust produced by a diesel engine

Diesel exhaust is the gaseous exhaust produced by a diesel type of internal combustion engine, plus any contained particulates. Its composition may vary with the fuel type or rate of consumption, or speed of engine operation, and whether the engine is in an on-road vehicle, farm vehicle, locomotive, marine vessel, or stationary generator or other application.

<span class="mw-page-title-main">Sawdust</span> Byproduct or waste product of woodworking operations (sawing, sanding, milling, etc.)

Sawdust is a by-product or waste product of woodworking operations such as sawing, sanding, milling and routing. It is composed of very small chips of wood. These operations can be performed by woodworking machinery, portable power tools or by use of hand tools. In some manufacturing industries it can be a significant fire hazard and source of occupational dust exposure.

<span class="mw-page-title-main">Intercalation (chemistry)</span> Reversible insertion of an ion into a material with layered structure

In chemistry, intercalation is the reversible inclusion or insertion of a molecule into layered materials with layered structures. Examples are found in graphite and transition metal dichalcogenides.

<span class="mw-page-title-main">Vanadium(V) oxide</span> Precursor to vanadium alloys and industrial catalyst

Vanadium(V) oxide (vanadia) is the inorganic compound with the formula V2O5. Commonly known as vanadium pentoxide, it is a brown/yellow solid, although when freshly precipitated from aqueous solution, its colour is deep orange. Because of its high oxidation state, it is both an amphoteric oxide and an oxidizing agent. From the industrial perspective, it is the most important compound of vanadium, being the principal precursor to alloys of vanadium and is a widely used industrial catalyst.

Occupational lung diseases comprise a broad group of diseases, including occupational asthma, industrial bronchitis, chronic obstructive pulmonary disease (COPD), bronchiolitis obliterans, inhalation injury, interstitial lung diseases, infections, lung cancer and mesothelioma. These can be caused directly or due to immunological response to an exposure to a variety of dusts, chemicals, proteins or organisms. Occupational cases of interstitial lung disease may be misdiagnosed as COPD, idiopathic pulmonary fibrosis, or a myriad of other diseases; leading to a delay in identification of the causative agent.

<span class="mw-page-title-main">Nickel(II) oxide</span> Chemical compound

Nickel(II) oxide is the chemical compound with the formula NiO. It is the principal oxide of nickel. It is classified as a basic metal oxide. Several million kilograms are produced annually of varying quality, mainly as an intermediate in the production of nickel alloys. The mineralogical form of NiO, bunsenite, is very rare. Other nickel oxides have been claimed, for example: Nickel(III) oxide(Ni
2O
3) and NiO
2, but they have yet to be proven by X-ray crystallography in bulk. Nickel(III) oxide nanoparticles have recently (2015) been characterized using powder X-ray diffraction and electron microscopy.

<span class="mw-page-title-main">Nanobatteries</span> Type of battery

Nanobatteries are fabricated batteries employing technology at the nanoscale, particles that measure less than 100 nanometers or 10−7 meters. These batteries may be nano in size or may use nanotechnology in a macro scale battery. Nanoscale batteries can be combined to function as a macrobattery such as within a nanopore battery.

<span class="mw-page-title-main">Lithium iron phosphate</span> Chemical compound

Lithium iron phosphate or lithium ferro-phosphate (LFP) is an inorganic compound with the formula LiFePO
4. It is a gray, red-grey, brown or black solid that is insoluble in water. The material has attracted attention as a component of lithium iron phosphate batteries, a type of Li-ion battery. This battery chemistry is targeted for use in power tools, electric vehicles, solar energy installations and more recently large grid-scale energy storage.

<span class="mw-page-title-main">Rachid Yazami</span> Moroccan scientist

Rachid Yazami is a Moroccan scientist, engineer, and inventor. He is best known for his critical role in the development of the graphite anode for lithium-ion batteries and his research on fluoride ion batteries.

A potassium-ion battery or K-ion battery is a type of battery and analogue to lithium-ion batteries, using potassium ions for charge transfer instead of lithium ions. It was invented by the Iranian/American chemist Ali Eftekhari in 2004.

Research in lithium-ion batteries has produced many proposed refinements of lithium-ion batteries. Areas of research interest have focused on improving energy density, safety, rate capability, cycle durability, flexibility, and cost.

<span class="mw-page-title-main">OCSiAl</span>

OCSiAl is a global nanotechnology company, the world's largest graphene nanotube manufacturer, conducting its operations worldwide. The OCSiAl headquarters are located in Luxembourg, with several offices in the United States, Europe and Asia.

A dual carbon battery is a type of battery that uses graphite as both its cathode and anode material. Compared to lithium-ion batteries, dual-ion batteries (DIBs) require less energy and emit less CO2 during production, have a reduced reliance on critical materials such as Ni or Co, and are more easily recyclable.

Conductive agents are used to ensure electrodes have good charge and discharge performance. Usually, a certain amount of conductive material is added during the production of the pole piece, and the micro current is collected between the active material and the current collector to reduce the micro current. The contact resistance of the electrode accelerates the rate of movement of electrons, and at the same time, can effectively increase the migration rate of lithium ions in the electrode material, thereby improving the charge and discharge efficiency of the electrode. The conductive agent carbon black is used for improving the conductivity of the electrodes and decreasing the resistance of interaction.

A solid-state silicon battery or silicon-anode all-solid-state battery is a type of rechargeable lithium-ion battery consisting of a solid electrolyte, solid cathode, and silicon-based solid anode.

<span class="mw-page-title-main">History of the lithium-ion battery</span> Overview of the events of the development of lithium-ion battery

This is a history of the lithium-ion battery.

References

  1. 1 2 3 4 Record in the GESTIS Substance Database of the Institute for Occupational Safety and Health
  2. ↑ Growney, David J.; Mykhaylyk, Oleksandr O.; Middlemiss, Laurence; Fielding, Lee A.; Derry, Matthew J.; Aragrag, Najib; Lamb, Gordon D.; Armes, Steven P. (2015-09-29). "Is Carbon Black a Suitable Model Colloidal Substrate for Diesel Soot?". Langmuir. 31 (38): 10358–10369. doi: 10.1021/acs.langmuir.5b02017 . ISSN   0743-7463. PMID   26344920. S2CID   206670654.
  3. ↑ "Experimental and kinetic study of the interaction of a commercial soot toward NO at high temperature" (PDF). Archived (PDF) from the original on 2013-02-15. Retrieved 2012-04-25.
  4. ↑ "Market Study: Carbon Black". Ceresana. Retrieved 2013-04-26.
  5. 1 2 3 4 5 6 Kuempel, Eileen D.; Sorahan, Tom (2010). "Identification of Research Needs to Resolve the Carcinogenicity of High-priority IARC Carcinogens" (PDF). Views and Expert Opinions of an IARC/NORA Expert Group Meeting, Lyon, France, 30 June – 2 July 2009. IARC Technical Publication No. 42. Lyon, France: International Agency for Research on Cancer. 42: 61–72. Retrieved August 30, 2012.
  6. ↑ Gnanamuthu, RM.; Lee, Chang Woo (2011-11-01). "Electrochemical properties of Super P carbon black as an anode active material for lithium-ion batteries". Materials Chemistry and Physics. 130 (3): 831–834. doi:10.1016/j.matchemphys.2011.08.060. ISSN   0254-0584.
  7. 1 2 3 Qi, Xin; Blizanac, Berislav; DuPasquier, Aurelien; Lal, Archit; Niehoff, Philip; Placke, Tobias; Oljaca, Miodrag; Li, Jie; Winter, Martin (2015). "Influence of Thermal Treated Carbon Black Conductive Additive on the Performance of High Voltage Spinel Cr-Doped LiNi 0.5 Mn 1.5 O 4 Composite Cathode Electrode". Journal of the Electrochemical Society. 162 (3): A339–A343. doi:10.1149/2.0401503jes. ISSN   0013-4651.
  8. 1 2 3 "Application Examples of carbon black". Mitsubishi Chemical. Retrieved 2013-01-14.
  9. ↑ Australia New Zealand Food Standards Code "Standard 1.2.4 – Labelling of ingredients" . Retrieved 2011-10-27.
  10. ↑ US FDA: "Color Additive Status List". Food and Drug Administration . Retrieved 2011-10-27.
  11. ↑ "Draft Screening Assessment for the Challenge". 29 January 2010. Retrieved 2013-01-14.
  12. ↑ "Australia New Zealand Food Standards Code". Archived from the original on 2012-12-20. Retrieved 2013-01-14.
  13. ↑ "What is carbon black". International carbon black Association. Archived from the original on 2009-04-01. Retrieved 2009-04-14.
  14. ↑ Carbon Black - A Global Market Overview Jan 2016 • Industry Experts Report CP024 • 328 pages
  15. ↑ Winter, J. and West FitzHugh, E., Pigments based on Carbon, in Berrie, B.H. Editor, Artists’ Pigments, A Handbook of Their History and Characteristics, Volume 4, pp. 1–37.
  16. ↑ Bone black, ColourLex
  17. ↑ Bomford D, Kirby J, Leighton, J., Roy A. Art in the Making: Impressionism. National Gallery Publications, London, 1990, pp. 112–119.
  18. ↑ Édouard Manet, 'Music in the Tuileries Gardens', ColourLex
  19. ↑ Hennion, Marie-Claire (July 2000). "Graphitized carbons for solid-phase extraction". Journal of Chromatography A. 885 (1–2): 73–95. doi:10.1016/S0021-9673(00)00085-6. PMID   10941668.
  20. 1 2 3 Hu, Jingwei; Zhong, Shengwen; Yan, Tingting (2021-10-01). "Using carbon black to facilitate fast charging in lithium-ion batteries". Journal of Power Sources. 508: 230342. Bibcode:2021JPS...50830342H. doi:10.1016/j.jpowsour.2021.230342. ISSN   0378-7753.
  21. ↑ Younesi, Reza; Christiansen, Ane Sælland; Scipioni, Roberto; Ngo, Duc-The; Simonsen, Søren Bredmose; Edström, Kristina; Hjelm, Johan; Norby, Poul (2015). "Analysis of the Interphase on Carbon Black Formed in High Voltage Batteries". Journal of the Electrochemical Society. 162 (7): A1289–A1296. doi: 10.1149/2.0761507jes . ISSN   0013-4651. S2CID   53486824.
  22. ↑ Dominko, Robert; Gaberscek, Miran; Drofenik, Jernej; Bele, Marjan; Pejovnik, Stane; Jamnik, Janko (2003-06-01). "The role of carbon black distribution in cathodes for Li ion batteries". Journal of Power Sources. Selected papers presented at the 11th International Meeting on Lithium Batteries. 119–121: 770–773. Bibcode:2003JPS...119..770D. doi:10.1016/S0378-7753(03)00250-7. ISSN   0378-7753.
  23. ↑ Sorahan T, Harrington JM (2007). "A "lugged" analysis of lung cancer risks in UK carbon black production workers, 1951–2004". Am J Ind Med. 50 (8): 555–564. doi:10.1002/ajim.20481. PMID   17516558.
  24. ↑ Ward EM, Schulte PA, Straif K, Hopf NB, Caldwell JC, Carreón T, DeMarini DM, Fowler BA, Goldstein BD, Hemminki K, Hines CJ, Pursiainen KH, Kuempel E, Lewtas J, Lunn RM, Lynge E, McElvenny DM, Muhle H, Nakajima T, Robertson LW, Rothman N, Ruder AM, Schubauer-Berigan MK, Siemiatycki J, Silverman D, Smith MT, Sorahan T, Steenland K, Stevens RG, Vineis P, Zahm SH, Zeise L, Cogliano VJ (2010). "Research recommendations for selected IARC-classified agents". Environmental Health Perspectives. 118 (10): 1355–62. doi:10.1289/ehp.0901828. PMC   2957912 . PMID   20562050.
  25. ↑ Morfeld P, McCunney RJ (2007). "Carbon black and lung cancer: Testing a new exposure metric in a German cohort". Am J Ind Med. 50 (8): 565–567. doi:10.1002/ajim.20491. PMID   17620319.
  26. ↑ "Occupational Safety and Health Guidelines for carbon black: Potential Human Carcinogen, Centres of Disease Control and Prevention, National Institute for Occupational Safety and Health" (PDF). Retrieved 2013-01-14.
  27. ↑ "Occupational Safety and Health Guideline for Carbon Black: Potential Human Carcinogen" (PDF). Centers of Disease Control and Prevention, National Institute for Occupational Safety and Health. Retrieved 11 January 2013.
  28. ↑ "CDC – NIOSH Pocket Guide to Chemical Hazards – Carbon black". www.cdc.gov. Retrieved 2015-11-27.

Further reading

This page is based on this Wikipedia article
Text is available under the CC BY-SA 4.0 license; additional terms may apply.
Images, videos and audio are available under their respective licenses.