Expander cycle

Last updated
Expander rocket cycle. Expander rocket engine (closed cycle). Heat from the nozzle and combustion chamber powers the fuel and oxidizer pumps. Expander rocket cycle.svg
Expander rocket cycle. Expander rocket engine (closed cycle). Heat from the nozzle and combustion chamber powers the fuel and oxidizer pumps.

The expander cycle is a power cycle of a bipropellant rocket engine. In this cycle, the fuel is used to cool the engine's combustion chamber, picking up heat and changing phase. The now heated and gaseous fuel then powers the turbine that drives the engine's fuel and oxidizer pumps before being injected into the combustion chamber and burned.

Contents

Because of the necessary phase change, the expander cycle is thrust limited by the square–cube law. When a bell-shaped nozzle is scaled, the nozzle surface area with which to heat the fuel increases as the square of the radius, but the volume of fuel to be heated increases as the cube of the radius. Thus beyond approximately 300 kN (70,000 lbf) of thrust, there is no longer enough nozzle area to heat enough fuel to drive the turbines and hence the fuel pumps. Higher thrust levels can be achieved using a bypass expander cycle where a portion of the fuel bypasses the turbine and or thrust chamber cooling passages and goes directly to the main chamber injector. Non-toroidal aerospike engines are not subject to the limitations from the square-cube law because the engine's linear shape does not scale isometrically: the fuel flow and nozzle area scale linearly with the engine's width. All expander cycle engines need to use a cryogenic fuel such as liquid hydrogen, liquid methane, or liquid propane that easily reaches its boiling point.

Some expander cycle engines may use a gas generator of some kind to start the turbine and run the engine until the heat input from the thrust chamber and nozzle skirt increases as the chamber pressure builds up.

Some examples of an expander cycle engine are the Aerojet Rocketdyne RL10 and the Vinci engine for the future Ariane 6. [1]

Expander bleed cycle

Expander bleed cycle. Expander open cycle (Also named coolant tap-off). Expander bleed cycle (coolant tap-off).svg
Expander bleed cycle. Expander open cycle (Also named coolant tap-off).

This operational cycle is a modification of the traditional expander cycle. In the bleed (or open) cycle, instead of routing all of the heated propellant through the turbine and sending it back to be combusted, only a small portion of the heated propellant is used to drive the turbine and is then bled off, being vented overboard without going through the combustion chamber. The other portion is injected into the combustion chamber. Bleeding off the turbine exhaust allows for a higher turbopump efficiency by decreasing backpressure and maximizing the pressure drop through the turbine. Compared with a standard expander cycle, this allows higher engine thrust at the cost of efficiency by dumping the turbine exhaust. [2] [3]

The Mitsubishi LE-5A was the world's first expander bleed cycle engine to be put into operational service. [4] The Mitsubishi LE-9 is the world's first first stage expander bleed cycle engine. [5]

Dual expander

In a similar way that the staged combustion can be implemented separately on the oxidizer and fuel on the full flow cycle, the expander cycle can be implemented on two separate paths as the dual expander cycle. The use of hot gases of the same chemistry as the liquid for the turbine and pump side of the turbopumps eliminates the need for purges and some failure modes. Additionally, when the density of the fuel and oxidizer is significantly different, as it is in the H2/LOX case, the optimal turbopump speeds differ so much that they need a gearbox between the fuel and oxidizer pumps. [6] [7] The use of dual expander cycle, with separate turbines, eliminates this failure-prone piece of equipment. [7]

Dual expander cycle can be implemented by either using separated sections on the regenerative cooling system for the fuel and the oxidizer, or by using a single fluid for cooling and a heat exchanger to boil the second fluid. In the first case, for example, you could use the fuel to cool the combustion chamber, and the oxidizer to cool the nozzle. In the second case, you could use the fuel to cool the whole engine and a heat exchanger to boil the oxidizer. [7]

Advantages

The expander cycle has a number of advantages over other designs:[ citation needed ]

Low temperature
After they have turned gaseous, the propellants are usually near room temperature, and do very little or no damage to the turbine, allowing the engine to be reusable. In contrast gas-generator or staged combustion engines operate their turbines at high temperature.
Tolerance
During the development of the RL10 engineers were worried that insulation foam mounted on the inside of the tank might break off and damage the engine. They tested this by putting loose foam in a fuel tank and running it through the engine. The RL10 chewed it up without problems or noticeable degradation in performance. Conventional gas-generators are in practice miniature rocket engines, with all the complexity that implies. Blocking even a small part of a gas generator can lead to a hot spot, which can cause violent loss of the engine. Using the engine bell as a 'gas generator' also makes it very tolerant of fuel contamination because of the wider fuel flow channels used.
Inherent safety
Because a bell-type expander-cycle engine is thrust limited, it can easily be designed to withstand its maximum thrust conditions. In other engine types, a stuck fuel valve or similar problem can lead to engine thrust spiraling out of control due to unintended feedback systems. Other engine types require complex mechanical or electronic controllers to ensure this does not happen. Expander cycles are by design incapable of malfunctioning that way.

Usage

Expander cycle engines include the following:

Comparison of upper-stage expander-cycle engines

Specifications
　 RL10B-2 BE-3U Vinci YF-75D YF-79 RD-0146D LE-5B LE-9
Country of originFlag of the United States (23px).png  United States Flag of the United States (23px).png  United States Flag of France.svg  France Flag of the People's Republic of China.svg  People's Republic of China Flag of the People's Republic of China.svg  People's Republic of China Flag of Russia.svg  Russia Flag of Japan.svg  Japan Flag of Japan.svg  Japan
CycleExpanderExpander bleed cycleExpanderExpanderExpanderExpanderExpander bleed cycle,
chamber expander		Expander bleed cycle
Thrust, vacuum110 kN (25,000 lbf)710 kN (160,000 lbf) [9] 180 kN (40,000 lbf)88.36 kN (19,860 lbf)250 kN (56,200 lbf)68.6 kN (15,400 lbf)137.2 kN (30,840 lbf)1471 kN (330,000 lbf) [10]
Mixture ratio5.885.86.06.055.9
Nozzle ratio2802408016011037
Isp, vacuum (s)462 [11] 457442.6455.2470447426
Chamber pressure (MPa)4.4126.14.17.05.93.5810.0
LH2 TP (rpm)65,00098,18052,000
LOX TP (rpm)18,000
Length (m)4.144.23.3582.793.8
Dry mass (kg)2772802652852400

See also

Related Research Articles

<span class="mw-page-title-main">Turbopump</span> Pump driven by a gas turbine

A turbopump is a propellant pump with two main components: a rotodynamic pump and a driving gas turbine, usually both mounted on the same shaft, or sometimes geared together. They were initially developed in Germany in the early 1940s. The purpose of a turbopump is to produce a high-pressure fluid for feeding a combustion chamber or other use. While other use cases exist, they are most commonly found in liquid rocket engines.

<span class="mw-page-title-main">RS-25</span> Space Shuttle and SLS main engine

The Aerojet Rocketdyne RS-25, also known as the Space Shuttle Main Engine (SSME), is a liquid-fuel cryogenic rocket engine that was used on NASA's Space Shuttle and is used on the Space Launch System (SLS).

<span class="mw-page-title-main">Rocketdyne F-1</span> Rocket engine used on the Saturn V rocket

The F-1, commonly known as Rocketdyne F-1, is a rocket engine developed by Rocketdyne. This engine uses a gas-generator cycle developed in the United States in the late 1950s and was used in the Saturn V rocket in the 1960s and early 1970s. Five F-1 engines were used in the S-IC first stage of each Saturn V, which served as the main launch vehicle of the Apollo program. The F-1 remains the most powerful single combustion chamber liquid-propellant rocket engine ever developed.

<span class="mw-page-title-main">Rocketdyne J-2</span> Rocket engine

The J-2, commonly known as Rocketdyne J-2, was a liquid-fuel cryogenic rocket engine used on NASA's Saturn IB and Saturn V launch vehicles. Built in the United States by Rocketdyne, the J-2 burned cryogenic liquid hydrogen (LH2) and liquid oxygen (LOX) propellants, with each engine producing 1,033.1 kN (232,250 lbf) of thrust in vacuum. The engine's preliminary design dates back to recommendations of the 1959 Silverstein Committee. Rocketdyne won approval to develop the J-2 in June 1960 and the first flight, AS-201, occurred on 26 February 1966. The J-2 underwent several minor upgrades over its operational history to improve the engine's performance, with two major upgrade programs, the de Laval nozzle-type J-2S and aerospike-type J-2T, which were cancelled after the conclusion of the Apollo program.

<span class="mw-page-title-main">Rocketdyne H-1</span> American kerolox rocket engine

The Rocketdyne H-1 was a 205,000 lbf (910 kN) thrust liquid-propellant rocket engine burning LOX and RP-1. The H-1 was developed for use in the S-I and S-IB first stages of the Saturn I and Saturn IB rockets, respectively, where it was used in clusters of eight engines. After the Apollo program, surplus H-1 engines were rebranded and reworked as the Rocketdyne RS-27 engine with first usage on the Delta 2000 series in 1974. RS-27 engines continued to be used up until 1992 when the first version of the Delta II, Delta 6000, was retired. The RS-27A variant, boasting slightly upgraded performance, was also used on the later Delta II and Delta III rockets, with the former flying until 2018.

<span class="mw-page-title-main">RL10</span> Liquid fuel cryogenic rocket engine, typically used on rocket upper stages

The RL10 is a liquid-fuel cryogenic rocket engine built in the United States by Aerojet Rocketdyne that burns cryogenic liquid hydrogen and liquid oxygen propellants. Modern versions produce up to 110 kN (24,729 lbf) of thrust per engine in vacuum. Three RL10 versions are in production for the Centaur upper stage of the Atlas V and the DCSS of the Delta IV. Three more versions are in development for the Exploration Upper Stage of the Space Launch System and the Centaur V of the Vulcan rocket.

<span class="mw-page-title-main">Staged combustion cycle</span> Rocket engine operation method

The staged combustion cycle is a power cycle of a bipropellant rocket engine. In the staged combustion cycle, propellant flows through multiple combustion chambers, and is thus combusted in stages. The main advantage relative to other rocket engine power cycles is high fuel efficiency, measured through specific impulse, while its main disadvantage is engineering complexity.

<span class="mw-page-title-main">Gas-generator cycle</span> Rocket engine operation method

The gas-generator cycle, also called open cycle, is one of the most commonly used power cycles in bipropellant liquid rocket engines. Part of the unburned propellant is burned in a gas generator and the resulting hot gas is used to power the propellant pumps before being exhausted overboard, and lost. Because of this loss, this type of engine is termed open cycle.

<span class="mw-page-title-main">Aerojet M-1</span> One of the largest rocket engines to be designed

The Aerojet M-1 was one of the largest and most powerful liquid-hydrogen-fueled liquid-fuel rocket engine to be designed and component-tested. It was originally developed during the 1950s by the US Air Force. The M-1 offered a baseline thrust of 6.67 MN and an immediate growth target of 8 MN. If built, the M-1 would have been larger and more efficient than the famed F-1 that powered the first stage of the Saturn V rocket to the Moon.

<span class="mw-page-title-main">Vinci (rocket engine)</span> European hydrolox rocket engine for upper stages under development

Vinci is a European Space Agency cryogenic liquid rocket engine under development as of 2020. It is designed to power the new upper stage of Ariane 6.

The YF-75 is a liquid cryogenic rocket engine burning liquid hydrogen and liquid oxygen in a gas generator cycle. It is China's second generation of cryogenic propellant engine, after the YF-73, which it replaced. It is used in a dual engine mount in the H-18 third stage of the Long March 3A, Long March 3B and Long March 3C launch vehicles. Within the mount, each engine can gimbal individually to enable thrust vectoring control. The engine also heats hydrogen and helium to pressurize the stage tanks and can control the mixture ratio to optimize propellant consumption.

<span class="mw-page-title-main">YF-77</span> Chinese rocket engine

The YF-77 is China's first cryogenic rocket engine developed for booster applications. It burns liquid hydrogen fuel and liquid oxygen oxidizer using a gas generator cycle. A pair of these engines powers the LM-5 core stage. Each engine can independently gimbal in two planes. Although the YF-77 is ignited prior to liftoff, the LM-5's four strap-on boosters provide most of the initial thrust in an arrangement similar to the European Vulcain on the Ariane 5 or the Japanese LE-7 on the H-II.

<span class="mw-page-title-main">LE-7</span> Japanese hydrolox staged combustion rocket engine

The LE-7 and its succeeding upgrade model the LE-7A are staged combustion cycle LH2/LOX liquid rocket engines produced in Japan for the H-II series of launch vehicles. Design and production work was all done domestically in Japan, the first major (main/first-stage) liquid rocket engine with that claim, in a collaborative effort from the National Space Development Agency (NASDA), Aerospace Engineering Laboratory (NAL), Mitsubishi Heavy Industries, and Ishikawajima-Harima. NASDA and NAL have since been integrated into JAXA. However, a large part of the work was contracted to Mitsubishi, with Ishikawajima-Harima providing turbomachinery, and the engine is often referred to as the Mitsubishi LE-7(A).

<span class="mw-page-title-main">LE-5</span> Japanese hydrolox rocket engine used on the H3 upper stage

The LE-5 liquid rocket engine and its derivative models were developed in Japan to meet the need for an upper stage propulsion system for the H-I and H-II series of launch vehicles. It is a bipropellant design, using LH2 and LOX. Primary design and production work was carried out by Mitsubishi Heavy Industries. In terms of liquid rockets, it is a fairly small engine, both in size and thrust output, being in the 89 kN (20,000 lbf) and the more recent models the 130 kN (30,000 lbf) thrust class. The motor is capable of multiple restarts, due to a spark ignition system as opposed to the single use pyrotechnic or hypergolic igniters commonly used on some contemporary engines. Though rated for up to 16 starts and 40+ minutes of firing time, on the H-II the engine is considered expendable, being used for one flight and jettisoned. It is sometimes started only once for a nine-minute burn, but in missions to GTO the engine is often fired a second time to inject the payload into the higher orbit after a temporary low Earth orbit has been established.

The RL60 was a planned liquid-fuel cryogenic rocket engine designed in the United States by Pratt & Whitney, burning cryogenic liquid hydrogen and liquid oxygen propellants. The engine runs on an expander cycle, running the turbopumps with waste heat absorbed from the main combustion process. This high-efficiency, waste heat based combustion cycle combined with the high-performance liquid hydrogen fuel enables the engine to reach a very high specific impulse of up to 465 seconds in a vacuum. The engine was planned to be a more capable successor to the Aerojet Rocketdyne RL10, providing improved performance and efficiency while maintaining the installation envelope of the RL10.

<span class="mw-page-title-main">Cryogenic rocket engine</span> Type of rocket engine which uses liquid fuel stored at very low temperatures

A cryogenic rocket engine is a rocket engine that uses a cryogenic fuel and oxidizer; that is, both its fuel and oxidizer are gases which have been liquefied and are stored at very low temperatures. These highly efficient engines were first flown on the US Atlas-Centaur and were one of the main factors of NASA's success in reaching the Moon by the Saturn V rocket.

<span class="mw-page-title-main">RD-0146</span> Russian rocket engine

The RD-0146 (РД-0146) is a liquid-fuel cryogenic rocket engine developed by KBKhA Kosberg in Voronezh, Russia.

<span class="mw-page-title-main">Aerojet LR87</span> American rocket engine family used on Titan missile first stages

The LR87 was an American liquid-propellant rocket engine used on the first stages of Titan intercontinental ballistic missiles and launch vehicles. Composed of twin motors with separate combustion chambers and turbopump machinery, it is considered a single unit and was never flown as a single combustion chamber engine or designed for this. The LR87 first flew in 1959.

TM65 is a rocket engine developed by Copenhagen Suborbitals. TM65 uses Ethanol and liquid oxygen as propellants in a pressure-fed power cycle.

The MARC-60, also known as MB-60, MB-XX, and RS-73, is a liquid-fuel cryogenic rocket engine designed as a collaborative effort by Japan's Mitsubishi Heavy Industries and US' Aerojet Rocketdyne. The engine burns cryogenic liquid oxygen and liquid hydrogen in an open expander cycle, driving the turbopumps with waste heat from the main combustion process.

References

  1. ↑ "Ariane 6". www.esa.int. Retrieved 21 February 2017.
  2. ↑ Sippel, Martin; Imoto, Takayuki; Haeseler, Dietrich (July 23, 2003). Studies on Expander Bleed Cycle Engines for Launchers (PDF). 39th AIAA/ASME/SAE/ASEE Joint Propulsion Conference and Exhibit. AIAA. Archived from the original (PDF) on 2016-03-03. Retrieved 2016-09-25.
  3. ↑ Atsumi, Masahiro; Yoshikawa, Kimito; Ogawara, Akira; Onga, Tadaoki (December 2011). "Development of the LE-X Engine" (PDF). Mitsubishi Heavy Industries Technical Review. Mitsubishi Heavy Industries. 48 (4): 36–43. Archived from the original (PDF) on 2015-12-24. Retrieved 2016-09-25.
  4. ↑ Akira Konno (October 1993). わが国の液体ロケットエンジンの現状と今後の展望 (in Japanese). Turbomachinery Society of Japan/J-STAGE. p. 10. Archived from the original on May 28, 2021. Retrieved January 24, 2022.
  5. ↑ Shinya Matsuura (February 2, 2021). H3ロケットの主エンジン「LE-9」熱効率向上で世界初に挑戦 (in Japanese). Nikkei Business. Archived from the original on January 24, 2022. Retrieved January 23, 2022.
  6. ↑ Sutton, George P.; Biblarz, Oscar (2000). "Section 6.6". Rocket Propulsion Elements: an introduction to the engineering of rockets (PDF) (Seventh ed.). John Wiley & Sons, Inc. pp. 221–227. ISBN   0-471-32642-9. Archived from the original (PDF) on 2016-01-19. Retrieved 26 September 2016.
  7. 1 2 3 USpatent 7,418,814 B1,Greene, William D.,"Dual expander cycle rocket engine with an intermediate, closed-cycle heat exchanger",issued 2008-09-02, assigned to The United States of America as represented by the Administrator of the National Aeronautics and Space Administration
  8. ↑ "Pratt & Whitney Space Propulsion – RL60 fact sheet". Archived from the original (PDF) on 2012-03-28. Retrieved 2008-12-28.
  9. ↑ "BE-3".
  10. ↑ WATANABE, DAIKI; MANAKO, HIROYASU; ONGA, TADAOKI; TAMURA, TAKASHI; IKEDA, KAZUFUMI; ISONO, MITSUNORI (December 2016). "Combustion Stability Improvement of LE-9 Engine for Booster Stage of H3 Launch Vehicle" (PDF). Mitsubishi Heavy Industries Technical Review. Retrieved 2024-03-13.
  11. ↑ "RL10 Engine | Aerojet Rocketdyne". Archived from the original on 2017-04-30. Retrieved 2017-06-06.
This page is based on this Wikipedia article
Text is available under the CC BY-SA 4.0 license; additional terms may apply.
Images, videos and audio are available under their respective licenses.