Abnormal grain growth

Last updated
Abnormal or discontinuous grain growth leads to a heterogeneous microstructure where a limited number of grains grow much faster than the rest. ContinuousDiscontinuousAnnealing.png
Abnormal or discontinuous grain growth leads to a heterogeneous microstructure where a limited number of grains grow much faster than the rest.

Abnormal or discontinuous grain growth, also referred to as exaggerated or secondary recrystallisation grain growth, is a grain growth phenomenon in which certain energetically favorable grains (crystallites) grow rapidly in a matrix of finer grains, resulting in a bimodal grain-size distribution.

Contents

In ceramic materials, this phenomenon can result in the formation of elongated prismatic, acicular (needle-like) grains in a densified matrix. This microstructure has the potential to improve fracture toughness by impeding the propagation of cracks. [1]

Mechanisms

Abnormal grain growth (AGG) is encountered in metallic or ceramic systems exhibiting one or more of several characteristics: [2] [3]

  1. Systems with secondary phase inclusions, precipitates or impurities above a certain threshold concentration.
  2. Systems with a highly anisotropic surface energy.
  3. Systems far from chemical equilibrium.

Abnormal grain growth occurs due to very high local rates of interface migration and is enhanced by the localized formation of liquid at grain boundaries. In 2023, Liss et al. [4] have shown that the spontaneous activation of a grain boundary opens diffusion pathways, leading to the activation of one grain in an otherwise inactive microstructure and allowing the grain to rotate and coalesce with a neighbor grain. However, due to competition with the surrounding grains, rotation may proceed erratically. Coupled with spontaneous activation, this makes abnormal grain growth a largely erratic process. While the activation of grain boundaries (leading to rotation and growth) can occur at temperatures well below the temperatures required for partial melting of the grain boundaries, the effect is emphasized when melting occurs.

Significance

In the sintering of ceramic materials, abnormal grain growth is often viewed as an undesirable phenomenon because rapidly growing grains may lower the hardness of the bulk material through Hall-Petch-type effects. However, the controlled introduction of dopants to bring about controlled AGG may be used to impart fibre-toughening in ceramic materials. Additionally, AGG is undesirable in piezoelectric ceramics, as it may degrade the piezoelectric effect.

Example systems

Abnormal grain growth observed in Rutile TiO2, induced by the presence of a zircon secondary phase. Abnormal Grain Growth in Rutile.png
Abnormal grain growth observed in Rutile TiO2, induced by the presence of a zircon secondary phase.
  1. Rutile (TiO2) frequently exhibits a prismatic or acicular growth habit. In the presence of alkali dopants or a solid-state ZrSiO4 dopant, rutile has been observed to crystallise from an anatase parent-phase in the form of abnormally large grains existing in a matrix of finer, equiaxed anatase or rutile grains. [3]
  2. Alumina, Al2O3 with silica and/or yttria dopants/impurities has been reported to exhibit undesirable AGG. [5]
  3. BaTiO3 barium titanate with an excess of TiO2 is known to exhibit abnormal grain growth with profound consequences on piezoelectric performance.
  4. Tungsten carbide has been reported to exhibit AGG of faceted grains in the presence of a liquid cobalt-containing phase at grain boundaries [6]
  5. Silicon nitride (Si3N4) may exhibit AGG depending on the size distribution of β-phase material in an α-Si3N4 precursor. This type of grain growth is of importance in the toughening of silicon nitride materials [7]
  6. Silicon carbide has been shown to exhibit improved fracture toughness as the result of AGG processes yielding elongated crack-tip/wake-bridging grains, with consequences for applications in ballistic armor. This enhancement of fracture toughness in ceramic materials via crack-bridging resulting from AGG is consistent with reported morphological effects on crack propagation in ceramics [1]
  7. Strontium barium niobate, used for electro-optics and dielectric applications, is known to exhibit AGG with significant consequences on the electronic performance of the material [8]
  8. Calcium titanate (CaTiO3, perovskite) systems doped with BaO have been observed to exhibit AGG without the formation of liquid as the result of polytype interfaces between solid phases [9]

See also

Related Research Articles

<span class="mw-page-title-main">Ceramic</span> An inorganic, nonmetallic solid prepared by the action of heat

A ceramic is any of the various hard, brittle, heat-resistant, and corrosion-resistant materials made by shaping and then firing an inorganic, nonmetallic material, such as clay, at a high temperature. Common examples are earthenware, porcelain, and brick.

<span class="mw-page-title-main">Sintering</span> Process of forming and bonding material by heat or pressure

Sintering or frittage is the process of compacting and forming a solid mass of material by pressure or heat without melting it to the point of liquefaction. Sintering happens as part of a manufacturing process used with metals, ceramics, plastics, and other materials. The nanoparticles in the sintered material diffuse across the boundaries of the particles, fusing the particles together and creating a solid piece.

<span class="mw-page-title-main">Silicon carbide</span> Extremely hard semiconductor

Silicon carbide (SiC), also known as carborundum, is a hard chemical compound containing silicon and carbon. A semiconductor, it occurs in nature as the extremely rare mineral moissanite, but has been mass-produced as a powder and crystal since 1893 for use as an abrasive. Grains of silicon carbide can be bonded together by sintering to form very hard ceramics that are widely used in applications requiring high endurance, such as car brakes, car clutches and ceramic plates in bulletproof vests. Large single crystals of silicon carbide can be grown by the Lely method and they can be cut into gems known as synthetic moissanite.

<span class="mw-page-title-main">High-strength low-alloy steel</span> Type of alloy steel

High-strength low-alloy steel (HSLA) is a type of alloy steel that provides better mechanical properties or greater resistance to corrosion than carbon steel. HSLA steels vary from other steels in that they are not made to meet a specific chemical composition but rather specific mechanical properties. They have a carbon content between 0.05 and 0.25% to retain formability and weldability. Other alloying elements include up to 2.0% manganese and small quantities of copper, nickel, niobium, nitrogen, vanadium, chromium, molybdenum, titanium, calcium, rare-earth elements, or zirconium. Copper, titanium, vanadium, and niobium are added for strengthening purposes. These elements are intended to alter the microstructure of carbon steels, which is usually a ferrite-pearlite aggregate, to produce a very fine dispersion of alloy carbides in an almost pure ferrite matrix. This eliminates the toughness-reducing effect of a pearlitic volume fraction yet maintains and increases the material's strength by refining the grain size, which in the case of ferrite increases yield strength by 50% for every halving of the mean grain diameter. Precipitation strengthening plays a minor role, too. Their yield strengths can be anywhere between 250–590 megapascals (36,000–86,000 psi). Because of their higher strength and toughness HSLA steels usually require 25 to 30% more power to form, as compared to carbon steels.

<span class="mw-page-title-main">Titanium diboride</span> Chemical compound

Titanium diboride (TiB2) is an extremely hard ceramic which has excellent heat conductivity, oxidation stability and wear resistance. TiB2 is also a reasonable electrical conductor, so it can be used as a cathode material in aluminium smelting and can be shaped by electrical discharge machining.

<span class="mw-page-title-main">Tantalum carbide</span> Chemical compound

Tantalum carbides (TaC) form a family of binary chemical compounds of tantalum and carbon with the empirical formula TaCx, where x usually varies between 0.4 and 1. They are extremely hard, brittle, refractory ceramic materials with metallic electrical conductivity. They appear as brown-gray powders, which are usually processed by sintering.

In materials science, the sol–gel process is a method for producing solid materials from small molecules. The method is used for the fabrication of metal oxides, especially the oxides of silicon (Si) and titanium (Ti). The process involves conversion of monomers into a colloidal solution (sol) that acts as the precursor for an integrated network of either discrete particles or network polymers. Typical precursors are metal alkoxides. Sol–gel process is used to produce ceramic nanoparticles.

<span class="mw-page-title-main">Barium titanate</span> Chemical compound

Barium titanate (BTO) is an inorganic compound with chemical formula BaTiO3. Barium titanate appears white as a powder and is transparent when prepared as large crystals. It is a ferroelectric, pyroelectric, and piezoelectric ceramic material that exhibits the photorefractive effect. It is used in capacitors, electromechanical transducers and nonlinear optics.

<span class="mw-page-title-main">Silicon nitride</span> Compound of silicon and nitrogen

Silicon nitride is a chemical compound of the elements silicon and nitrogen. Si
3N
4 is the most thermodynamically stable and commercially important of the silicon nitrides, and the term ″Silicon nitride″ commonly refers to this specific composition. It is a white, high-melting-point solid that is relatively chemically inert, being attacked by dilute HF and hot H
3PO
4. It is very hard. It has a high thermal stability with strong optical nonlinearities for all-optical applications.

In materials science, grain growth is the increase in size of grains (crystallites) in a material at high temperature. This occurs when recovery and recrystallisation are complete and further reduction in the internal energy can only be achieved by reducing the total area of grain boundary. The term is commonly used in metallurgy but is also used in reference to ceramics and minerals. The behaviors of grain growth is analogous to the coarsening behaviors of grains, which implied that both of grain growth and coarsening may be dominated by the same physical mechanism.

<span class="mw-page-title-main">Ceramic engineering</span> Science and technology of creating objects from inorganic, non-metallic materials

Ceramic engineering is the science and technology of creating objects from inorganic, non-metallic materials. This is done either by the action of heat, or at lower temperatures using precipitation reactions from high-purity chemical solutions. The term includes the purification of raw materials, the study and production of the chemical compounds concerned, their formation into components and the study of their structure, composition and properties.

<span class="mw-page-title-main">Ceramography</span> Preparation and study of ceramics with optical instruments

Ceramography is the art and science of preparation, examination and evaluation of ceramic microstructures. Ceramography can be thought of as the metallography of ceramics. The microstructure is the structure level of approximately 0.1 to 100 μm, between the minimum wavelength of visible light and the resolution limit of the naked eye. The microstructure includes most grains, secondary phases, grain boundaries, pores, micro-cracks and hardness microindentations. Most bulk mechanical, optical, thermal, electrical and magnetic properties are significantly affected by the microstructure. The fabrication method and process conditions are generally indicated by the microstructure. The root cause of many ceramic failures is evident in the microstructure. Ceramography is part of the broader field of materialography, which includes all the microscopic techniques of material analysis, such as metallography, petrography and plastography. Ceramography is usually reserved for high-performance ceramics for industrial applications, such as 85–99.9% alumina (Al2O3) in Fig. 1, zirconia (ZrO2), silicon carbide (SiC), silicon nitride (Si3N4), and ceramic-matrix composites. It is seldom used on whiteware ceramics such as sanitaryware, wall tiles and dishware.

<span class="mw-page-title-main">Solid</span> State of matter

Solid is one of the four fundamental states of matter along with liquid, gas, and plasma. The molecules in a solid are closely packed together and contain the least amount of kinetic energy. A solid is characterized by structural rigidity and resistance to a force applied to the surface. Unlike a liquid, a solid object does not flow to take on the shape of its container, nor does it expand to fill the entire available volume like a gas. The atoms in a solid are bound to each other, either in a regular geometric lattice, or irregularly. Solids cannot be compressed with little pressure whereas gases can be compressed with little pressure because the molecules in a gas are loosely packed.

<span class="mw-page-title-main">Bioceramic</span> Type of ceramic materials that are biocompatible

Bioceramics and bioglasses are ceramic materials that are biocompatible. Bioceramics are an important subset of biomaterials. Bioceramics range in biocompatibility from the ceramic oxides, which are inert in the body, to the other extreme of resorbable materials, which are eventually replaced by the body after they have assisted repair. Bioceramics are used in many types of medical procedures. Bioceramics are typically used as rigid materials in surgical implants, though some bioceramics are flexible. The ceramic materials used are not the same as porcelain type ceramic materials. Rather, bioceramics are closely related to either the body's own materials or are extremely durable metal oxides.

The CeramTec Group is a developer and manufacturer of products and components made of technical ceramics. The products are marketed through its own sales companies, among others. They are primarily used in medical technology, automotive engineering, electronics, equipment and mechanical engineering, environmental and energy technology, toolmaking, the chemical industry and the semiconductor industry. The company is headquartered in Plochingen in Baden-Württemberg, Germany.

<span class="mw-page-title-main">Ceramic matrix composite</span> Composite material consisting of ceramic fibers in a ceramic matrix

In materials science ceramic matrix composites (CMCs) are a subgroup of composite materials and a subgroup of ceramics. They consist of ceramic fibers embedded in a ceramic matrix. The fibers and the matrix both can consist of any ceramic material, including carbon and carbon fibers.

<span class="mw-page-title-main">MAX phases</span>

The MAX phases are layered, hexagonal carbides and nitrides which have the general formula: Mn+1AXn, (MAX) where n = 1 to 4, and M is an early transition metal, A is an A-group (mostly IIIA and IVA, or groups 13 and 14) element and X is either carbon and/or nitrogen. The layered structure consists of edge-sharing, distorted XM6 octahedra interleaved by single planar layers of the A-group element.

Ultra-high-temperature ceramics (UHTCs) are a type of refractory ceramics that can withstand extremely high temperatures without degrading, often above 2,000 °C. They also often have high thermal conductivities and are highly resistant to thermal shock, meaning they can withstand sudden and extreme changes in temperature without cracking or breaking. Chemically, they are usually borides, carbides, nitrides, and oxides of early transition metals.

In materials science, toughening refers to the process of making a material more resistant to the propagation of cracks. When a crack propagates, the associated irreversible work in different materials classes is different. Thus, the most effective toughening mechanisms differ among different materials classes. The crack tip plasticity is important in toughening of metals and long-chain polymers. Ceramics have limited crack tip plasticity and primarily rely on different toughening mechanisms.

References

  1. 1 2 Padture, N. P.; Lawn, B. R. (1994). "Toughness properties of a silicon carbide with an in situ induced heterogeneous grain structure". J. Am. Ceram. Soc. 77 (10): 2518–2522. doi:10.1111/j.1151-2916.1994.tb04637.x.
  2. ↑ Kang, S.-J. L. (2005). Sintering: Densification, Grain Growth, and Microstructure. Elsevier Butterworth-Heinemann. ISBN   9780080493077.
  3. 1 2 3 Hanaor, D. A. H.; Xu, W.; Ferry, M.; Sorrell, C. C. (2012). "Abnormal grain growth of rutile TiO2 induced by ZrSiO4". Journal of Crystal Growth . 359: 83–91. arXiv: 1303.2761 . Bibcode:2012JCrGr.359...83H. doi:10.1016/j.jcrysgro.2012.08.015. S2CID   94096447.
  4. ↑ Liss, K.-D.; Xu, P.G.; Shiro, A.; Zhang, S.Y.; Yukutake, E.; Shobu, T.; Akita, K. (2023). "Abnormal Grain Growth: A Spontaneous Activation of Competing Grain Rotation". Advanced Engineering Materials . 26 (4): 2300470. doi: 10.1002/adem.202300470 .
  5. ↑ Bae, I.-J.; Baik, S. (1997). "Abnormal grain growth of alumina". J. Am. Ceram. Soc. 80 (5): 1149–1156. doi:10.1111/j.1151-2916.1997.tb02957.x.
  6. ↑ Park, Y. J.; Hwang, N. M.; Yoon, D. Y. (1996). "Abnormal growth of faceted (WC) grains in a (Co) liquid matrix". Metall. Mater. Trans. 27 (9): 2809–2819. Bibcode:1996MMTA...27.2809P. doi:10.1007/bf02652373. S2CID   137080942.
  7. ↑ Dressler, W.; Kleebe, H.-J.; Hoffmann, M. J.; Rühle, M.; Petzow, G. (1996). "Model experiments concerning abnormal grain growth in silicon nitride". J. Eur. Ceram. Soc. 16 (1): 3–14. doi:10.1016/0955-2219(95)00175-1.
  8. ↑ Lee, H.-Y.; Freer, R. (1997). "The mechanism of abnormal grain growth in Sr0.6Ba0.4Nb2O6 ceramics". J. Appl. Phys. 81 (1): 376–382. Bibcode:1997JAP....81..376L. doi:10.1063/1.364122.
  9. ↑ Recnik, A. (2001). "Polytype induced exaggerated grain growth in ceramics". J. Eur. Ceram. Soc. 21 (10): 2117–2121. doi:10.1016/s0955-2219(01)00184-4.
This page is based on this Wikipedia article
Text is available under the CC BY-SA 4.0 license; additional terms may apply.
Images, videos and audio are available under their respective licenses.