Air lock diving-bell plant

Last updated
The barge as depicted in a painting by Charles Pears The Times history of the war (1914) (14577627960).jpg
The barge as depicted in a painting by Charles Pears

Gibraltar Harbour's air lock diving-bell plant, or caisson diving bell barge, was a purpose-built barge for the laying, examination and repair of moorings for battleships. [1] [2] [3] [4] It was designed by Siebe Gorman & Company of Lambeth and Forrestt & Co. Ltd of Wivenhoe in Essex, who built and supplied it in 1902 for the British Admiralty. [1]

Contents

Local conditions at Gibraltar dictated the need for such a craft. The heavy harbour moorings have three chains extending out radially along the seabed from a central ring, each terminating in a large anchor. Most harbours have a soft seabed, and it is usual to lay down moorings by settling anchors in the mud, clay or sand, but this could not be done in Gibraltar harbour where the seabed is hard rock. [5]

For Gibraltar the seabed needed to be dug out sufficiently for an anchor point to hold. The barge would be towed over the work site, moored in place with anchors, and the bell would be lowered to the seabed. [6] [3] [7] Air pumped into the bell would displace the water, and workers accessed the bell through the airlock in the central access shaft. [3] [7] This system allowed continuous work with changes of workmen in four-hour shifts, [3] [7] and allowed men to work on the seabed in normal work clothing. [5]

In 1969 the Gibraltar Chronicle reported the plant as still working in the harbour; it was believed to be the only vessel of its type in the world.

Description

Pictured on trials at Wivenhoe 1902 Caisson Diving Bell Barge BF73 001 079 060 (cropped).jpg
Pictured on trials at Wivenhoe 1902

The specially commissioned steel barge weighing 346 tons [8] was 85 feet (26 m) long, with a beam of 38 feet 6 inches (11.73 m); [4] [9] a draught of 7 feet 3 inches (2.21 m), [4] [8] and moulded depth 7 feet 9 inches (2.36 m). [9] The plant was fitted out with an air lock diving-bell system, a decompression chamber and other rescue equipment. [3] [7]

The bell had a working chamber measuring 15 ft (4.6 m) long, [9] by 10 feet 6 inches (3.20 m) wide by 7 feet 6 inches (2.29 m) high. The central access shaft was 37 feet 6 inches (11.43 m) high and 3 ft (0.91 m) in diameter. [6] The bell was built by Siebe Gorman at their factory in Lambeth of steel plates, with cast-iron ballast, and its total weight was about 46 tons. [10] It was electrically lit and fitted with a telephone for communicating with the air-compressor and lifting-winch rooms on the barge, [6] and a compressed air rock drill. [4] The air-lock bell was effectively a mobile engineering caisson, and the barge was its launch and recovery system.

The wire ropes for lowering and raising the bell worked over pulleys mounted on a lifting frame superstructure erected over a well through the centre of the hull. Two sets of air compressors were fitted on the deck, one set for supplying air to the bell, the other for powering the pneumatic rock drill. The greatest depth at which the bell could work was 40 ft (12 m). [6]

The bell commonly worked at a little lower than 15 psi (100 kPa) roughly one atmosphere more than sea level atmospheric pressure; [5] equal to a depth of approximately 35 feet (11 m) of water. [11]

Construction

The Admiralty ordered the vessel for His Majesty's Dockyard in early 1902. [12] It was designed by Siebe Gorman of Lambeth [10] and Forrestt & Co. Ltd of Wivenhoe in Essex, who built and supplied it in 1902 [8] [13] The plant was also trialled by Forrestt at their yard on the upstream side of the River Colne in Wivenhoe. This company, established in 1788, had a long track record in the construction of specialized vessels and naval equipment for the Admiralty, as well as the War Office, Crown Agents, and the Royal National Lifeboat Institution. [12]

The yard's Loft book confirms the vessel was completed in 1902 and its yard number as 463. Forrestt's boilermakers constructed the bell at Wivenhoe to Siebe Gorman's design. [8] Her trials took place on the River Colne before September, and she was the "subject of great interest to the fish, numbers of which attracted by the light (from within the bell), swarmed around it". [14] The completed diving-bell barge was towed direct from Wivenhoe to Gibraltar. [15] Shortly after its delivery, back home in England, the Essex Newsman reported: "Henry Turner, mariner, was charged with being drunk and disorderly at Wivenhoe, on 1 September 1902. It was stated the defendant had gone to Gibraltar in the diving-bell barge recently built at Wivenhoe for the Admiralty. PC Hailstone said the defendant used the worst language he ever heard in his twenty years service. Fined 10s and 4s costs". [15]

The cost to the Admiralty of the entire plant, including the barge, was about £14,000. [6] An illustration of the plant was included in the influential 1909 Diving Manual by Sir Robert Davis, who was head of design at Siebe Gorman at the time. [3] [16]

Operations

A cross section of the mobile air lock diving bell Mobile Air Lock Diving Bell cross section.jpg
A cross section of the mobile air lock diving bell
Working inside the bell on the sea floor Working inside the bell on the sea floor.jpg
Working inside the bell on the sea floor

The Plant's task was to bury each of three anchors for a mooring deep into the seabed. [5]

A mooring vessel (in the 1960s, HMS Moorland) would first lay out the mooring components in position. [5]

Good weather was required for operation of the bell, and the barge would be moored with six or eight anchors to keep it in place. [3] [7] The barge had no means of propulsion, and was towed into place over each mooring anchor by tugs which also laid out the barge's anchors. Once anchored, the barge was capable of making fine adjustments to its position by using the winches to haul on the anchors. [5]

The access tube on the bell was sealed at the top, making it airtight, and the bell lowered through a moon pool to the seabed over the position where the anchor was to be bedded. A compressor was used to equalize the air pressure inside the bell and access tube with the water pressure at the bottom opening of the bell, this would displace the water in the bell and leave an air-filled space above the level of the rim in which workers could operate. The working chamber of the bell was bottomless, allowing workmen to stand and work directly on the seabed within an air filled space. [5]

Men would climb down into the entry tube and through an airlock and then go down a vertical ladder into the working chamber. Once the anchor's position was marked, a winch (mounted on the deck's lifting frame, its wires passing through the chamber)[ clarification needed ] would lift the anchor and the barge would move, placing the anchor to one side. The barge would then return to its original position and four men in the chamber would commence digging a hole big enough for placement of the anchor. [5]

Working in dank, dingy, pressurized conditions, the men would skim off a thin layer of mud and attack the rock, first with pickaxes; as the hole deepened, one man would hold a crowbar for another to swing a sledgehammer. The rock, chipped out into boulders, would then be passed up by hands from the hole. Digging the hole would take two or three days until it was shoulder-high and deep enough for the anchor. [5]

Once the anchors were embedded in the holes, the mooring tender vessel would take the place of the barge to complete the mooring system, using her two 10-ton winches for the job in hand. The completed moorings would then be left in place, with buoys for markers, as permanent installations. [5]

The 1960s

The plant showing a modified funnel after a boiler refit Air Lock Diving-Bell Plant with modifications after a refit.jpg
The plant showing a modified funnel after a boiler refit

At some point the barge had a new boiler installed, its cabin enlarged to suit, and a new, larger funnel fitted. In 1969 the Gibraltar Chronicle reported the plant as still working in the harbour; it was believed to be the only vessel of its type in the world. The system described was used for providing moorings in the late 1960s for the Mr. Louie oil rig when it visited the Bay. [5]

Moorland

Mooring vessel Moorland Moorland 1938 HMS - Mooring Vessel.jpg
Mooring vessel Moorland

The mooring vessel HMS Moorland was built in 1938 on the Clyde by William Simons & Co of Renfrew. She initially served at Scapa, and then in the late 1940s on the Clyde and Rosyth, before being transferred to Gibraltar in 1961. She was to end her days sunk as target practice for HMS Juno on 26 January 1971 in the western Mediterranean. [17] Moorland was fitted with two 10-ton winches capable of heavy lifts from the seabed, and carried all the cables and anchors required for laying the moorings. The vessel was crewed by a Master, two engineers, and ten ratings — five for the deck and five for the engine room. In addition, when on mooring duty, she also carried a chargeman (supervisory worker) and twelve deckhands. [5]

Related Research Articles

Anchor Device used to secure a vessel to the bed of a body of water to prevent the craft from drifting

An anchor is a device, normally made of metal, used to secure a vessel to the bed of a body of water to prevent the craft from drifting due to wind or current. The word derives from Latin ancora, which itself comes from the Greek ἄγκυρα (ankȳra).

The timeline of underwater diving technology is a chronological list of notable events in the history of the development of underwater diving equipment. With the partial exception of breath-hold diving, the development of underwater diving capacity, scope, and popularity, has been closely linked to available technology, and the physiological constraints of the underwater environment.

SS <i>Yongala</i> Australian registered passenger ship that sank off Cape Bowling Green, Queensland, Australia

SS Yongala was a passenger and cargo ship that sank off Cape Bowling Green, Queensland, Australia on 23 March 1911. En route from Melbourne to Cairns she steamed into a cyclone and sank south of Townsville.

Mooring Any permanent structure to which a vessel may be secured at an terrestrial surface.

A mooring is any permanent structure to which a vessel may be secured. Examples include quays, wharfs, jetties, piers, anchor buoys, and mooring buoys. A ship is secured to a mooring to forestall free movement of the ship on the water. An anchor mooring fixes a vessel's position relative to a point on the bottom of a waterway without connecting the vessel to shore. As a verb, mooring refers to the act of attaching a vessel to a mooring.

Standard diving dress Copper helmet with rubberised canvas diving suit and weighted boots

Standard diving dress, also known as hard-hat or copper hat equipment, or heavy gear, is a type of diving suit that was formerly used for all relatively deep underwater work that required more than breath-hold duration, which included marine salvage, civil engineering, pearl shell diving and other commercial diving work, and similar naval diving applications. Standard diving dress has largely been superseded by lighter and more comfortable equipment.

Diving bell Chamber for transporting divers vertically through the water

A diving bell is a rigid chamber used to transport divers from the surface to depth and back in open water, usually for the purpose of performing underwater work. The most common types are the open-bottomed wet bell and the closed bell, which can maintain an internal pressure greater than the external ambient. Diving bells are usually suspended by a cable, and lifted and lowered by a winch from a surface support platform. Unlike a submersible, the diving bell is not designed to move under the control of its occupants, nor to operate independently of its launch and recovery system.

Siebe Gorman British manufacturer of diving equipment and salvage contractor

Siebe Gorman & Company Ltd was a British company that developed diving equipment and breathing equipment and worked on commercial diving and marine salvage projects. The company advertised itself as 'Submarine Engineers'. It was founded by Augustus Siebe, a German-born British engineer chiefly known for his contributions to diving equipment.

Thames sailing barge

A Thames sailing barge is a type of commercial sailing boat once common on the River Thames in London. The flat-bottomed barges with a shallow draught and leeboards, were perfectly adapted to the Thames Estuary, with its shallow waters and narrow tributary rivers. The larger barges were seaworthy vessels, and were the largest sailing vessel to be handled by just two men. The average size was about 120 tons and they carried 4,200 square feet (390 m2) of canvas sail in six working sails. The mainsail was loose-footed and set up with a sprit, and was brailed to the mast when not needed. It is sheeted to a horse, as is the foresail; they require no attention when tacking. The foresail is often held back by the mate to help the vessel come about more swiftly.

Caisson (engineering) Rigid structure to provide workers with a dry working environment below water level

In geotechnical engineering, a caisson is a watertight retaining structure used, for example, to work on the foundations of a bridge pier, for the construction of a concrete dam, or for the repair of ships. Caissons are constructed in such a way that the water can be pumped out, keeping the work environment dry. When piers are being built using an open caisson, and it is not practical to reach suitable soil, friction pilings may be driven to form a suitable sub-foundation. These piles are connected by a foundation pad upon which the column pier is erected.

Braye Harbour is the main harbour on the north side of the Island of Alderney, in the Channel Islands, a dependency of the British Crown. A 3,000 feet (910 m) break-water was built by the Admiralty to protect the Navy in the 19th century shelters Braye Harbour. It is an artificial harbour created by building a pier or jetty. The harbour faces out onto the Swinge, which is part of the English Channel. It is here that most of the island's freight comes in. It is more or less a suburb of St Anne, which is a large settlement in Alderney that juts out on a rocky promontory on the west side, approximately 1 mile from the harbour.

Heinke was a series of companies that made diving equipment in London, run by members of a Heinke family.

USNS <i>Safeguard</i> (T-ARS-50)

USNS Safeguard (T-ARS-50),, is the lead ship of her class and the second United States Navy ship of that name.

Gibdock Dockyard in Gibraltar

Gibdock is a shipyard in the British overseas territory of Gibraltar. It formerly operated as a Royal Navy Dockyard.

Motorised Submersible Canoe WWII British frogman delivery vehicle

The Motorised Submersible Canoe (MSC), nicknamed Sleeping Beauty, was built by the British Special Operations Executive (SOE) during World War II as an underwater vehicle for a single frogman to perform clandestine reconnaissance or attacks against enemy vessels.

Commercial offshore diving Professional diving in support of the oil and gas industry

Commercial offshore diving, sometimes shortened to just offshore diving, generally refers to the branch of commercial diving, with divers working in support of the exploration and production sector of the oil and gas industry in places such as the Gulf of Mexico in the United States, the North Sea in the United Kingdom and Norway, and along the coast of Brazil. The work in this area of the industry includes maintenance of oil platforms and the building of underwater structures. In this context "offshore" implies that the diving work is done outside of national boundaries. Technically it also refers to any diving done in the international offshore waters outside of the territorial waters of a state, where national legislation does not apply. Most commercial offshore diving is in the Exclusive Economic Zone of a state, and much of it is outside the territorial waters. Offshore diving beyond the EEZ does also occur, and is often for scientific purposes.

HMS <i>Spanker</i> (1889)

HMS Spanker was a Sharpshooter-class torpedo gunboat of the Royal Navy. She was launched in 1889, converted to a minesweeper in 1909 and sold for breaking in 1920.

History of underwater diving History of the practice of descending below the waters surface to interact with the environment

The history of underwater diving starts with freediving as a widespread means of hunting and gathering, both for food and other valuable resources such as pearls and coral, By classical Greek and Roman times commercial applications such as sponge diving and marine salvage were established, Military diving also has a long history, going back at least as far as the Peloponnesian War, with recreational and sporting applications being a recent development. Technological development in ambient pressure diving started with stone weights (skandalopetra) for fast descent. In the 16th and 17th centuries diving bells became functionally useful when a renewable supply of air could be provided to the diver at depth, and progressed to surface supplied diving helmets—in effect miniature diving bells covering the diver's head and supplied with compressed air by manually operated pumps—which were improved by attaching a waterproof suit to the helmet and in the early 19th century became the standard diving dress.

The Thistle SALM was a tanker loading facility that allowed oil from the Thistle oilfield to be transported to land where a submarine export pipeline did not yet exist. It was also the site of the August 8, 1979 Wildrake diving accident that killed two divers. and the January 21, 1981 Stena Seaspread diving accident (non-fatal).

SB <i>Centaur</i> British wooden Thames sailing barge

SB Centaur is a wooden Thames sailing barge, built in Harwich, Essex, England in 1895. She was used to carry various cargoes, mainly grain, for the next 60 years. During the First World War she carried food and coal to the French Channel ports. During the Second World War Centaur was damaged when sailing to assist with the Dunkirk Evacuation. She did war work for the duration of the conflict.

Offshore embedded anchors Type of anchor

Offshore embedded anchors are anchors that derive their holding capacity from the frictional, or bearing, resistance of the surrounding soil, as opposed to gravity anchors, which derive their holding capacity largely from their weight. As offshore developments move into deeper waters, gravity-based structures become less economical due to the large size needed and the consequent cost of transportation.

References

  1. 1 2 3 "Entrance to a Diving-Bell". Illustrated London News: 1 (Cover). 25 March 1906. An air-compression vessel, used for laying moorings for battleships, fitted with a diving-bell, the entrance to which is down the big funnel amidships.
  2. 1 2 "CLIII. The Navy's work in 1916". The Times History of the War. The Times. Vol. X. 1917. p. 60. Retrieved 30 April 2019.
  3. 1 2 3 4 5 6 7 Davis, RH (1909). Diving Scientifically and Practically Considered. Being a Diving Manual and Handbook of Submarine Appliances (6th ed.). Tolworth, Surbiton, Surrey: Siebe Gorman & Company Ltd. p. 693.
  4. 1 2 3 4 5 6 7 8 9 10 11 12 Barlow, Doug (1969). "Getting down to the job". Gibraltar Chronicle. Archived from the original on 26 July 2004. Retrieved 1 May 2019– via Minewarfare & Clearance Diving Officers' Association.
  5. 1 2 3 4 5 Davis, Robert Henry (1911). "Divers and Diving Apparatus"  . In Chisholm, Hugh (ed.). Encyclopædia Britannica . Vol. 8 (11th ed.). Cambridge University Press. pp. 326–331.
  6. 1 2 3 4 5 "Airlock Diving Bell Plant". divinglocker.tripod.com. Retrieved 30 April 2019.
  7. 1 2 3 4 Collins, John. "Forrestt Shipyard, Wivenhoe". wivenhoehistory.org.uk. Nottage Maritime Institute, Wivenhoe. Retrieved 4 May 2019.
  8. 1 2 3 "Caisson diving bell barge". Mersea Museum. 1905. Archived from the original on 1 May 2019. Retrieved 2 May 2019. Caisson diving bell barge built for the Admiralty for service in Gibraltar. Forrestt & Co. Ltd, 1905 Catalogue, Page 59.
  9. 1 2 Davis, Robert H. (31 August 1934). "Deep diving and under water rescue: II". Journal of the Royal Society of Arts. Royal Society for the Encouragement of Arts, Manufactures and Commerce. 82 (4267): 1049–1065. JSTOR   41360195.
  10. ↑ "Convert Pounds Per Square Inch to Feet Of Water". kylesconverter.com. Retrieved 12 May 2019.
  11. 1 2 "Shipbuilding at Wivenhoe". East Anglian Daily Times . 27 March 1902 – via britishnewspaperarchive.co.uk. The shipbuilding trade is extremely brisk just now at Wivenhoe... at the fine yards of Forrestt and Sons, Limited'
  12. ↑ "Caisson diving bell barge". Mersea Museum. 1905. Archived from the original on 1 May 2019. Retrieved 1 May 2019. Caisson diving bell barge built for the Admiralty for service in Gibraltar. Forrestt & Co. Ltd. See 1905 Catalogue, Page 59 for more info
  13. ↑ "A House Under Water". The Wichita Daily Eagle. Wichita, Kansas, USA. 24 October 1902. p. 4. Retrieved 4 May 2019– via newspaperarchive.com.
  14. 1 2 "Petty Sessions – Lexdean and Winstree, Sept 6th John Bateman, Esq., chairman". Essex Newsman. 13 September 1902. Henry Turner, mariner
  15. ↑ "John Player cigarette cards". vintage-diving-shop.com. Retrieved 1 May 2019.
  16. ↑ "Moorland 1938 HMS - Mooring Vessel". Clyde Maritime. 22 November 2011. Archived from the original on 3 May 2019. Retrieved 3 May 2019.
This page is based on this Wikipedia article
Text is available under the CC BY-SA 4.0 license; additional terms may apply.
Images, videos and audio are available under their respective licenses.