Albion 4-speed synchromesh (MR9N) David Brown 4-speed constant mesh (NS3N) Albion 5 or 6-speed constant-mesh (NS3AN)
Dimensions
Length
23ft (7.0m) for 29 to 36 seats
The Albion Nimbus was an underfloor-engined, ultra-lightweight (dry weight 2.4 tonne) midibus or coach chassis, with a four-cylinder horizontal diesel engine and a gross vehicle weight of six tons. It was largely operated on light rural bus duties and private hires. Operators who used it on heavy-duty bus routes found it insufficiently robust. It was the first Albion bus chassis to have a name that did not begin with the letter V. The design was revised twice and was produced from 1955 to 1965.
Albion Motors had been taken over by Leyland Motors in 1951: after the merger, Albion were to concentrate on export models and lightweight chassis for the home market. With this in mind, Albion developed the EN219 engine, a horizontal four-cylinder unit sharing design and components with the six-cylinder Leyland O350. It was launched in 1953 for the underfloor-engined Albion Claymore delivery truck. During 1954, Scottish Omnibuses (SOL) used Claymore units in an integrally constructed rubber-suspended 32-seater bus, this being announced in May 1955 with the Nimbus being unveiled, in the autumn, at the 1955 Scottish Motor Show at Kelvin Hall, Glasgow. The vehicle on the show stand had an Alexander body and was an Albion demonstrator in SOL livery, whilst the bus in the demonstration park in Highland Omnibuses livery carried a body by SOL, now preserved.
Description
The Nimbus had a bolted lightweight steel frame with channel section longitudinals and tubular cross-members, similar to the Claymore, also featuring a down-sloping front section. During its production life, component changes followed those of the Claymore.
MR9N
The frame was slightly wider than that of the longest MR7L Claymore but the wheelbase was identical and the radiator was mounted in an inclined position above the front axle, to obviate intrusion into the passenger gangway. Wider and longer springs were fitted and the axles were of wider tack, suitable for 8ft (2.4m) wide bodies. Like the MR 5 and 7 Claymore the 3.83-litre EN219 developing 60bhp (45kW) at 2200rpm drove through an Albion single-plate hydraulically assisted clutch and Albion four-speed constant-mesh gearbox, with synchromesh on third and top, to an Albion overhead worm rear axle, the Nimbus rear axle was heavier-duty than that of the heaviest Claymore and had larger brakes. Braking was provided by two-leading-shoe drum brakes all round, hydraulically actuated with vacuum assistance from an Albion-patented engine bypass valve. The engine had an oil-bath air-cleaner and a centrifugal oil filter. Automatic chassis lubrication was standard.
NS3N
In 1958, the Claymore range was revised with a lower specification and greater use of bought-in components in an attempt to reduce costs and thus it was hoped make the line profitable. Nomenclature was now based on model name, the Claymores becoming models CL5N and CL3N or L and the Nimbus model NS3N. Axles were now of Austin (under British Motor Corporation) design, from their 5-ton truck, the rear axle being of spiral-bevel form and a David Brown four-speed constant mesh gearbox was fitted. There was not a wide version of the BMC axles, so the NS3 had a width over tyres of 7ft 1in (2,160mm), rather than the MR9s 7ft 7in (2,310mm). The engine was the enlarged Albion EN250, a 4.1-litre unit developing 72bhp (54kW) at 2,200rpm.
NS3AN
In 1960, along with the rest of the Claymore range, the Nimbus was uprated, featuring heavier BMC axles and an Albion constant mesh gearbox with either five or six speeds. Vacuum assistance to the brakes was now provided by a Hydrovac system, belt-driven from the engine. Two Nimbus-specific changes were the option of a drop-frame extension at the rear for a luggage boot and the option of a spare wheel mounted on a slide-out carrier, below this extension.
Sales
In Scotland, SBG fleets Alexander (five MR9 and ten NS3 coaches) and Highland (six MR9 coaches) were the largest purchasers new. The BET group were the major purchasers in England and Wales. Devon General had nine, Maidstone & District fifteen, and Western Welsh purchased 48. The municipal purchasers of the type were Wallesey (4) Southampton (3) Great Yarmouth (6) and Halifax (10) Independents bought buses and coaches, bus customers included W Gash & Sons of Newark, Notts, LCW Motors of Llandeillo, North Wales and the Londonderry and Lough Swilly Railway, operating between Northern Ireland and the north-western parts of the Irish Republic. Smiths of Wigan and Dickson of Dundee were among the purchasers of Nimbus coaches, these were generally bodied by Plaxton, to either front or centre-entrance layout. On Guernsey the linked Guernsey Motors and Guernsey Railways concerns took 32 between them and independent Watson's Greys also owned one, these all had narrow bus bodies by Reading of Portsmouth.
Coachwork on UK/Channel Island examples, was by Alexanders, Harrington, Plaxton, Reading, SOL, Strachans, Weymann and Willowbrook.
One major export market for the type was Australia, and one independent operator there stretched its examples to 27ft (8.5m) before fitting them both with 39-seat bus bodies, although the greatest seating capacity for any Nimbus was a standard-length 41-seat school bus for Dunbartonshire County Education Department.
Operation
In contrast with the EN286 through to EN335 series, which were developed for around a decade before release and subject to continual improvement thereafter, the EN218/9 was a rush job, going from concept to production in little over two years. Adams and Milligan quote gasket failures as a particular early problem, comparing the Leyland-inspired use of four securing studs per cylinder rather than the six Albion had used hitherto. They say the Claymore and in particular the Nimbus garnered a reputation for unreliability resulting in uneconomic volumes being sold: that must have applied especially to the 30cwt payload MLH3 Cairn derivative of the Claymore which was barely in production for a year before being dropped.
Of course the underfloor-engined concept had advantages in small delivery trucks. Guy had its Seal and Dennis its Stork around the same time but they sold even worse than the Claymore; although Atkinson had a reliable UFE truck, as did Büssing in West Germany.
It's undeniable though that the idea of a small OMO bus with the amenity of a full size UFE single deck was appealing to certain customers. Notably Scottish Bus Group who used Claymore units and Metalastic rubber suspension in an integral prototype built by Scottish Omnibuses in 1954. It was in the demonstration park of the 1955 Kelvin Hall show that the Nimbus was unveiled and Buses Illustrated's Scottish Columnist wondered why a firm whose motto was "Sure as the Sunrise" had named a vehicle after a raincloud, going on to say that given its emission of black smoke on starting that perhaps it was a cumulo-nimbus.
Geoffrey Hillditch spends a quarter of his chapter on Albion buses detailing the Nimbus and his mostly negative experience of it. His first sight of it was at the 1956 Earls Court show, he had served his time at LNER's Gorton Loco works so he was incredulous at the flimsiness of the frame with a chassis weighing only 2ton 17.25cwt, but he says "I recognised the logic behind the inception of the design."
One of the first problems he encountered with the Great Yarmouth MR9s was, that in order for the automatic bypass vacuum generator to provide sufficient vacuum for braking assistance idling speed had to be kept low, this resulted in an engine straining at its mountings. Eventually failure of the mountings happened on one of them but not before another managed to shed its dynamo whilst in service, others had sheared a number of chassis brackets. He also found the gearchange linkage (although it kept the engine in place when the mountings failed) developed far too much free play and in order to select reverse on one he had to open the half-door on the passenger side of the cab. Others managed to grind to a halt when two gears were selected simultaneously.
He ordered the short-tailed AEC Reliances to replace them. Then he returned to Halifax as GM and chief engineer to be greeted by ten NS3ANs. First came gasket failures, and in some cases he found part of the block burned away too, which he ascribed to incorrect combustion chamber design. BMC rear axle design was faulty, with half shafts cutting into sealing rings and starving the differential of oil. The automatic lubrication equipment, driven by an extension of the speedometer cable, frequently failed and failure of chassis brackets (as in the MR9s) was common. The use of a conventional engine driven vacuum-exhauster was given as a good point but the six-speed gearbox was in this implementation imprecise in operation.
Whilst praising Albion's service engineers and finding the MR9s good for 11mpg‑imp (26L/100km; 9.2mpg‑US) on the Norfolk coast and the six-speed NS3ANs returned 12mpg‑imp (24L/100km; 10.0mpg‑US)-13mpg‑imp (22L/100km; 11mpg‑US) "and could do even better on a route where the overdrive could be engaged for reasonable periods" his conclusion was "[N]ippy and economical though a heavy town centre route was no place for a Nimbus."
Nimbus production amounted to 124 MR9 and 217 NS3. The largest user was Western Welsh, who kept them to deeply rural routes. In contrast 471 Albion Aberdonians were built over a shorter period.
Although operators using the Nimbus on intensive one-man-operated routes found it troublesome, on the lightly trafficked rural routes for which it was designed it could put in a long life. Harvey of Mousehole, Cornwall operated an ex-Halifax bus from 1966 to 1986, while other rural operators who got good value out of second-hand Nimbuses were Wiles of Port Seton in East Lothian, Scotland, and Booth and Fisher who operated on the borderlands of Yorkshire and Nottinghamshire.
Preservation
One MR9L and 21 NS3N/NS3AN Nimbuses are preserved. The body from one of the Western Welsh examples was removed by the operator and refitted to the prototype Bristol LHS6L chassis which was registered XBO1F and is now preserved with Thornes Independent of Selby, Yorks.
Derivatives
Bristol Commercial Vehicles built the SU model from 1960 to 1966, this featured the same EN250 engine and BMC rear-axle as the Nimbus NS3AN with a David Brown overdrive-top five-speed constant-mesh gearbox, all were bodied by Eastern Coach Works, most to 25ft (8m) length, seating 36 (buses) or 33 (coaches) although a shorter-wheelbase 30-seat model 23ft (7.0m) long was also built. The major difference from the Nimbus was that the radiator was mounted at the extreme front of the chassis. It was concentrated in the south-west of England, the customers for the 179 built were eight Transport Holding Company fleets. Southern and Western National had 97 (36 of which were coaches, out of 38 coaches built). Bristol Omnibus Company had nine short buses. West Yorkshire Road Car had 18 longer buses, United Automobile Services five, United Counties Omnibus Company had six and United Welsh Services had the other two coaches. At least three Bristol SU survive, one each from Western National and Bristol, and the last West Yorkshire example, EWT386C which was re-engined with a Perkins H6-354 engine as part of the Bristol LH development programme. Thornes Independent also preserve this bus as part of their heritage fleet.
Seddon Atkinson Vehicles Limited, was a manufacturer of large goods vehicles based in Oldham, Lancashire, England, was formed after the acquisition in 1970 of Atkinson Vehicles Limited of Preston by Seddon Diesel Vehicles Limited of Oldham. In 1974, the firm was acquired by International Harvester, which sold it in March 1984 to the Spanish group Enasa which made it a subsidiary of Pegaso. In 1990, it became part of Iveco which used the brand for various types of specialised vehicles in the United Kingdom. The range of models produced included EuroMover, Pacer and Strato, which are aimed at refuse collection, recycling and construction operators.
Albion Motors was a Scottish automobile and commercial vehicle manufacturer.
The Leyland Titan was a forward-control chassis with a front-mounted engine designed to carry double-decker bus bodywork. It was built mainly for the United Kingdom market between 1927 and 1942, and between 1945 and 1969.
The Leyland Atlantean is a predominantly double-decker bus chassis manufactured by Leyland Motors between 1958 and 1986. Only 17 Atlantean chassis were bodied as single deck from new.
The Bristol VR was a rear-engined double-decker bus chassis which was manufactured by Bristol Commercial Vehicles as a competitor to the Leyland Atlantean and Daimler Fleetline.
The Leyland Leopard was a mid-engined single-decker bus and single-decker coach chassis manufactured by Leyland between 1959 and 1982.
The Leyland Tiger Cub was a lightweight underfloor-engined chassis manufactured by Leyland between 1952 and 1970.
The Daimler Roadliner was a single-decker bus and coach chassis built by Daimler between 1962 and 1972. Notoriously unreliable, it topped the 1993 poll by readers of Classic Bus as the worst bus type ever, beating the Guy Wulfrunian into second place. It was very technologically advanced, offering step-free access some 20 years before other buses; as a coach, it was felt by industry commentators to be in advance of contemporary UK designs.
The Leyland Panther Cub was a rear-engined single-decker bus manufactured by Leyland between 1964 and 1968. A shorter derivative of the Panther built on request to Manchester Corporation Transport, only 94 buses on this chassis were built for operators in England and Wales.
The Albion Aberdonian was an underfloor-engined bus designed and manufactured by Albion Motors between 1957 and 1960, it was introduced as a longer derivative of the Albion Nimbus.
The Daimler Freeline was an underfloor-engined bus chassis built by Daimler between 1951 and 1964. It was a very poor seller in the UK market for an underfloor-engined bus and coach chassis, but became a substantial export success.
The Leyland Lion, coded as PSR1, was a bus chassis manufactured by Leyland as its first production rear engined single decker. It was announced in 1960, although the first two were built in 1959. 56 LPSR1 and 28 PSR1 were sold to 1967 which was low for Leyland at the time. It was the third of five Leyland bus models to carry the Lion brand.
The Seddon Pennine RU was a rear-engined single-decker bus built by Seddon Diesel Vehicles/Seddon Atkinson between 1969 and 1974.
The Leyland Tiger is a heavyweight half-cab single-decker bus and coach chassis built by Leyland Motors between 1927 — 1942 and 1946 — 1968.
The Seddon Pennine 7 was a mid-underfloor-engined single-deck bus or coach chassis built by Seddon Atkinson between 1974 and 1982.
The Leyland Royal Tiger Worldmaster, sometimes simply known as the Leyland Worldmaster, was a mid-underfloor-engined single-decker bus or single-decker coach chassis manufactured by Leyland between 1954 and 1979.
The Bristol LH was a single-decker bus chassis built by Bristol Commercial Vehicles (BCV) in Bristol, England. Nearly 2,000 were built between 1967 and 1982 in a variety of sizes and body types, including some as goods vehicles.
The Bristol SU was a single-decker bus and single-decker coach chassis built by Bristol Commercial Vehicles between 1960 and 1966. The bodies for these vehicles were built by Eastern Coach Works (ECW). Some of them were built as medium length chassis, whereas most of them were built as full length chassis.
The Albion Lowlander was a Scottish-built low-height double-decker bus.
The Leyland Royal Tiger PSU was an underfloor-engined bus and coach chassis manufactured by Leyland between 1950 and 1954.
This page is based on this Wikipedia article Text is available under the CC BY-SA 4.0 license; additional terms may apply. Images, videos and audio are available under their respective licenses.
