Arresting gear

Last updated

An F-14 Tomcat descends to make an arresting gear landing on the flight deck of USS Theodore Roosevelt (CVN-71) in 2002 US Navy 020312-N-7265D-005 F-14.jpg
An F-14 Tomcat descends to make an arresting gear landing on the flight deck of USS Theodore Roosevelt (CVN-71) in 2002

An arresting gear, or arrestor gear, is a mechanical system used to rapidly decelerate an aircraft as it lands. Arresting gear on aircraft carriers is an essential component of naval aviation, and it is most commonly used on CATOBAR and STOBAR aircraft carriers. Similar systems are also found at land-based airfields for expeditionary or emergency use. Typical systems consist of several steel wire ropes laid across the aircraft landing area, designed to be caught by an aircraft's tailhook. During a normal arrestment, the tailhook engages the wire and the aircraft's kinetic energy is transferred to hydraulic damping systems attached below the carrier deck. There are other related systems that use nets to catch aircraft wings or landing gear. These barricade and barrier systems are only used for emergency arrestments for aircraft without operable tailhooks.

Contents

History

Fairey III-F aircraft landing on board British aircraft carrier HMS Furious circa early 1930s. Arresting gear wires are visible above the flight deck HMS Furious-19.jpg
Fairey III-F aircraft landing on board British aircraft carrier HMS Furious circa early 1930s. Arresting gear wires are visible above the flight deck

Arresting cable systems were invented by Hugh Robinson [ when? ] and were utilized by Eugene Ely on his first landing on a ship—the armored cruiser USS Pennsylvania, on 18 January 1911. These early systems had cables run through pulleys and attached to dead weights, such as sandbags. More modern arresting cables were tested on HMS Courageous in June 1931, designed by Commander C. C. Mitchell. [1]

Modern U.S. Navy aircraft carriers have the Mark 7 Mod 3 arresting gear installed, which have the capability of recovering a 50,000-pound (23 t) aircraft at an engaging speed of 130 knots (240 km/h; 150 mph) in a distance of 344 feet (105 m) in two seconds. [2] :52 The system is designed to absorb theoretical maximum energy of 47.5 million foot-pounds (64.4 MJ) at maximum cable run-out.

Prior to the introduction of the angled flight deck, two systems were used (in addition to deck cables) to keep landing aircraft from running into parked aircraft further forward on the flight deck: the barrier and the barricade. If the aircraft tailhook failed to catch a wire, its landing gear would be caught by a 3–4-foot-high (0.91–1.22 m) net known as the barrier. If the aircraft caught a wire upon touchdown, the barrier could be quickly lowered to allow aircraft to taxi over it. The final safety net was the barricade, a large, 15-foot-high (4.6 m) net that prevented landing aircraft from crashing into other aircraft parked on the bow. Barriers are no longer in use, although ground-based arresting gear are sometimes called "barriers". Barricades are still in use aboard carriers, but they are only rigged and used in emergencies.

Operation

A cross-deck pendant milliseconds after an aircraft nose-wheel passes over it. The arched supports are leaf springs that raise the pendant above the flight deck. Aircraft Carrier 3-wire.jpg
A cross-deck pendant milliseconds after an aircraft nose-wheel passes over it. The arched supports are leaf springs that raise the pendant above the flight deck.

A normal arrestment is accomplished when the arresting hook of an incoming aircraft engages one of the deck pendants. [3] When a landing aircraft engages a deck pendant, the force of the forward motion of the landing aircraft is transferred to a purchase cable, which is routed via sheaves to the arresting engine, located in a machinery room below the flight deck or on either side of the runway. As the deck pendant and the purchase cable are pulled out by the aircraft being arrested, the kinetic energy of the aircraft is transferred to mechanical energy of the cables, and the arresting engine transfers the mechanical energy of the cables to hydraulic energy. This classic system of hydraulic arrest is now being supplanted by one using electromagnetics where the energy absorption is controlled by a turbo-electric engine. The arresting engine brings about a smooth, controlled stop of the landing aircraft. At the completion of the arrestment, the aircraft arresting hook is disengaged from the deck pendant, which is then retracted to its normal position.

Sea-based systems

A Grumman A-6 Intruder about to catch the #3 wire. VA-34 KA-6D Intruder tailhook approaching arresting cable on USS Dwight D. Eisenhower (CVN-69) Fleet Ex 1990 DN-ST-90-05264.jpg
A Grumman A-6 Intruder about to catch the #3 wire.

Modern carriers typically have three or four arresting cables laid across the landing area. All U.S. carriers in the Nimitz-class, along with Enterprise, have four wires, with the exception of USS Ronald Reagan and USS George H.W. Bush, which have only three. [4] Gerald R. Ford-class carriers will also have three. Pilots aim for the second wire for the three-wire configuration or third wire for the four-wire configuration to reduce the risk of landing short. Aircraft coming in to land on a carrier are at approximately 85% of full throttle. At touchdown, the pilot advances the throttles to Military (MIL) power. In the F/A-18E/F Super Hornet and EA-18G Growler aircraft, the aircraft automatically reduces engine thrust to 70% once the deceleration of a successful arrestment is detected. This feature can be overridden by the pilot by selecting max afterburner. If the aircraft fails to catch an arresting cable, a condition known as a "bolter", the aircraft has sufficient power to continue down the angled flight deck and become airborne again. Once the arresting gear stops the aircraft, the pilot brings the throttles back to idle, raises the hook and taxies clear.

In addition to American CVNs (nuclear aircraft carriers), the French Charles de Gaulle, the Russian Admiral Kuznetsov, the Chinese Liaoning, as well as the Indian Vikramaditya are active or future aircraft carriers installed with arresting gear.

Land-based systems

U.S. Marines work on an arresting engine for a land based arresting system. Note reel for nylon tape in background. Marines working on aircraft arresting gear.jpg
U.S. Marines work on an arresting engine for a land based arresting system. Note reel for nylon tape in background.

Land-based military airfields operating fighter or jet trainer aircraft also use arresting gear systems, although they are not required for all landings. Instead, they are used for landing aircraft on short or temporary runways, or for emergencies involving brake failure, steering problems or other situations in which using the full length of the runway is not possible or safe. There are three basic types of land based systems: permanent, expeditionary, and overrun gear.

An F-16 makes a field arrestment. F-16 field arrestment.jpg
An F-16 makes a field arrestment.

Permanent systems are installed on nearly all U.S. military airfields operating fighter or jet trainer aircraft. Expeditionary systems are similar to permanent systems and are used for landing aircraft on short or temporary runways. Expeditionary systems are designed to be installed or uninstalled in only a few hours.

Overrun gear consisting of hook cables and/or elastic nets known as barriers are commonly used as a backup system. Barrier nets catch the wings and fuselage of an aircraft and use an arresting engine or other methods such as anchor chains or bundles of woven textile material to slow the aircraft down. On some land-based airfields where the overrun area is short, a series of concrete blocks referred to as an engineered materials arrestor system (EMAS) is used. These materials are used to catch the landing gear of an aircraft and slow it via rolling resistance and friction. Aircraft are stopped by the transfer of energy required to crush the blocks. Unlike other types of arresting gear, EMAS is also used at some civilian airports where the overrun area is shorter than would normally be allowed.

The first use of a barrier on a military airfield was during the Korean War when jet fighters had to operate from shorter airfields where there was no margin for error. The system used was just a transplant of the Davis Barrier used on straight deck carriers to keep any aircraft that missed the arrest wires from crashing into the aircraft parked forward of the landing area. But instead of the more complex hydraulic system used on carriers to stop the aircraft when it hits the barrier the land based system used heavy ship anchor chains to bring the aircraft to a halt. [5]

Components

New cross-deck pendants are coiled and ready for quick installation. Cross deck pendants.jpg
New cross-deck pendants are coiled and ready for quick installation.

The major systems that make up typical arresting gear are the hook cable or pendants, purchase cables or tapes, sheaves and arresting engines. [6]

Cross-deck pendant

A-gear mechanics replace a leaf spring. Arresting Gear mechanics.jpg
A-gear mechanics replace a leaf spring.

Also known as arresting cables or wires, cross-deck pendants are flexible steel cables that are spanned across the landing area to be engaged by the arresting hook of an incoming aircraft. On aircraft carriers there are either three or four cables, numbered 1–4 from aft to forward. Pendants are made of wire rope with a diameter of 1, 1+14 or 1+38 inches (25, 32 or 35 mm). Each wire rope is made up of numerous strands twisted about an oiled hemp center core, which provides a "cushion" for each strand and also supplies cable lubrication. The cable ends are equipped with terminal couplings designed for quick detachment during replacement and are able to be rapidly detached and replaced (in about 2–3 minutes on aircraft carriers). [6] On U.S. carriers, the arresting cables are removed and replaced after each 125 arrested landings. [7] Individual cables are often removed and left "stripped" in order to perform maintenance on other components of the arresting gear during aircraft recoveries (using other, on line, systems). Wire supports raise the deck pendants several inches so that they may be picked up by the tailhook of a landing aircraft. The wire supports on carriers are merely curved steel leaf springs that can flex to allow an aircraft to taxi over the installed deck pendant. On land based systems, 15 cm-diameter "donut"-shaped rubber supports raise the cable off the runway surface approximately 7.5 cm. [8]

Purchase cables or tapes

The purchase cable is a wire rope that looks very similar to the arresting cable. They are much longer, however, and are not designed to be easily removed. There are two purchase cables per arresting cable, and they connect to each end of the arresting wire. Purchase cables connect the arresting wire to the arresting gear engines and "pay out" as the arresting wire is engaged by the aircraft. As an incoming aircraft engages the deck pendant, the purchase cable transmits the force of the landing aircraft from the deck gear to the arresting engine. The pendant (arresting wire) is "swaged" (attached) to the purchase cable by means of a loop created with zinc heated to 1,000 °F (538 °C). This onboard fabrication is considered dangerous, and it is reported the US Navy is testing the use of an automated press to accomplish it more safely. [2] :56 [6] On land based systems, heavy nylon tapes are used in place of purchase cables, but they serve the same function.

Sheaves

Purchase cables or tapes run through sheaves in the flight deck or alongside of the runway to the arresting engines. Damper sheaves act as hydraulic shock absorbers that provide for the increased landing speeds.

Spray-type arrest gear

In 1957 the concept of a piston being pulled through a tube of water was first purposed as a cheap arrest gear system for land airbases. [9] In the early 1960s, the British took this basic concept and developed a spray-type arrest gear system for both land and sea use. The engine had hydraulic cylinders that moved through water filled pipe, with a smaller pipe alongside that has holes of various size along its length. The Royal Navy claimed that there was no theoretical weight limit, but there was a speed limit. [10]

Arresting engines

An F/A-18 Hornet engages the #4 wire, with the white retractable deck sheave in the foreground. VFA-147 FA-18C Hornet catching arresting wire on USS Nimitz (CVN-68) 971106-N-6939M-269.jpg
An F/A-18 Hornet engages the #4 wire, with the white retractable deck sheave in the foreground.

Each pendant has its own engine systems that absorb and dispel the energies developed when a landing aircraft is arrested. On American Nimitz-class carriers, hydro-pneumatic systems are used, each weighing 43 short tons (39  t ), wherein oil is hydraulically forced out of a cylinder by a ram connected to the purchase cable, through a control valve. [2] :52 [6] A major development in arresting gear was the constant runout control valve, which controls the fluid flow from the engine cylinder to the accumulator and is designed to stop all aircraft with the same amount of runout regardless of mass and speed. The aircraft's weight is set by each arresting gear engine's operator. During normal operations, a "single weight setting" is used for simplicity. This weight is usually the maximum landing, or "max trap", weight for the aircraft. In certain cases, usually aircraft malfunctions, which affect approach speed, a "single weight setting" is used to ensure proper energy absorption by the system. The operator is given the weight of the aircraft by the air officer in Primary Flight Control. The operator then sets the constant runout control valve to the appropriate weight setting for that aircraft. The pressure setting for the arresting gear engine remains at a constant pressure of about 400 psi (2,800 kPa). The constant runout valve (CROV) stops the aircraft, as opposed to hydraulic pressure.[ citation needed ]

Permanent and expeditionary land based systems usually consist of two arresting engines located on either side of the runway. The arresting engines apply braking force to reels holding the purchase tapes, which in turn slow the aircraft and bring it to a stop. The two most common methods used by land based arresting engines to apply the braking force are the rotary friction brake and the rotary hydraulic, or "water twister", systems. The rotary friction brake is simply a hydraulic pump coupled to the reel, which applies a graduated pressure to multi-disc brakes mounted on the reel. The rotary hydraulic system is a turbine inside a water/glycol-filled housing coupled to the reel. The turbulence generated in the water/glycol mixture by the turbine during the arrestment provides the resistance to slow the reel and stop the aircraft. Once the aircraft is released from the cable, the tapes and cable are retracted by an internal combustion engine or electric motor installed on the arresting engine.[ citation needed ]

Excessive runout during an arrestment is a condition known as a "two-block." This name is derived from naval parlance when all the line has been pulled through a pulley system, the two pulley blocks are touching, hence "two blocked". Excessive runout can be caused by improper arresting gear settings, excess aircraft gross weight, excess aircraft engagement speed, or excess airplane thrust applied during the arrestment. Off center landings also have the danger of damaging the arresting gear.[ citation needed ]

Advanced Arresting Gear landing system

Electromagnets are being used in the new Advanced Arresting Gear (AAG) system on American aircraft carriers. The current system (above) relies on hydraulics to slow and stop a landing aircraft. While the hydraulic system is effective, as demonstrated by more than fifty years of implementation, the AAG system offers a number of improvements. The current system is unable to capture unmanned aerial vehicles (UAVs) without damaging them due to extreme stresses on the airframe. UAVs do not have the necessary mass to drive the large hydraulic piston used to trap heavier, manned airplanes. By using electromagnetics the energy absorption is controlled by a turbo-electric engine. This makes the trap smoother and reduces shock on airframes. Even though the system will look the same from the flight deck as its predecessor, it will be more flexible, safe, and reliable, and will require less maintenance and manning. [11] This system is being trialed on the USS Gerald R. Ford and will be installed on all of the Gerald R. Ford-class aircraft carriers.

Barricade

Carrier barricade in the raised position Aircraft carrier barricade.jpg
Carrier barricade in the raised position
A S-3A Viking making an emergency landing into the barricade on the flight deck of the USS Abraham Lincoln (CVN-72). The aircraft was unable to make a normal arrested recovery because of damaged landing gear. US Navy DN-SC-93-04867 to 04876 S-3A Viking emergency landing USS Abraham Lincoln (CVN-72) animation.gif
A S-3A Viking making an emergency landing into the barricade on the flight deck of the USS Abraham Lincoln (CVN-72). The aircraft was unable to make a normal arrested recovery because of damaged landing gear.

The barricade is an emergency recovery system used only when a normal (pendant) arrestment cannot be made. The barricade is normally in a stowed condition and rigged only when required. To rig a barricade, it is stretched across the flight deck between stanchions, which are raised from the flight deck. Rigging the barricade is routinely practiced by U.S. carrier flight deck personnel; a well trained crew can accomplish the task in under three minutes. [6]

The barricade webbing consists of upper and lower horizontal loading straps joined to each other at the ends. Five vertical engaging straps, spaced 20 feet (6.1 m) apart, are connected to each upper and lower load strap. The barricade webbing is raised to a height of approximately 20 feet. The barricade webbing engages the wings of the landing aircraft, wherein energy is transmitted from the barricade webbing through the purchase cable to the arresting engine. Following a barricade arrestment, the webbing and deck cables are discarded and the stanchions are lowered back into their recessed slots. Barricade engagements are rare, as tailhooks are designed to be extremely fail-safe, and an aircraft returning from combat with such severe damage would likely not be able to land. This device has been installed on all American aircraft carriers and on the French Charles de Gaulle, while Brazilian CATOBAR and Russian and Indian STOBAR aircraft carriers have only conventional arresting gear installed.[ citation needed ]

See also

Related Research Articles

<span class="mw-page-title-main">Aircraft carrier</span> Warship that serves as a seagoing airbase

An aircraft carrier is a warship that serves as a seagoing airbase, equipped with a full-length flight deck and facilities for carrying, arming, deploying, and recovering aircraft. Typically, it is the capital ship of a fleet, as it allows a naval force to project air power worldwide without depending on local bases for staging aircraft operations. Carriers have evolved since their inception in the early twentieth century from wooden vessels used to deploy balloons to nuclear-powered warships that carry numerous fighters, strike aircraft, helicopters, and other types of aircraft. While heavier aircraft such as fixed-wing gunships and bombers have been launched from aircraft carriers, these aircraft have not landed on a carrier. By its diplomatic and tactical power, its mobility, its autonomy and the variety of its means, the aircraft carrier is often the centerpiece of modern combat fleets. Tactically or even strategically, it replaced the battleship in the role of flagship of a fleet. One of its great advantages is that, by sailing in international waters, it does not interfere with any territorial sovereignty and thus obviates the need for overflight authorizations from third-party countries, reduces the times and transit distances of aircraft and therefore significantly increases the time of availability on the combat zone.

In aviation, a go-around is an aborted landing of an aircraft that is on final approach or has already touched down. A go-around can either be initiated by the pilot flying or requested by air traffic control for various reasons, such as an unstabilized approach or an obstruction on the runway.

Aviation is the design, development, production, operation, and use of aircraft, especially heavier-than-air aircraft. Articles related to aviation include:

<span class="mw-page-title-main">Assisted take-off</span> System used to help aircraft get into the air

In aviation, assisted takeoff is any system for helping aircraft to get into the air. The reason it might be needed is due to the aircraft's weight exceeding the normal maximum takeoff weight, insufficient power, insufficient available runway length, or a combination of all three factors. Assisted takeoff is also required for gliders, which do not have an engine and are unable to take off by themselves.

<span class="mw-page-title-main">Flight deck</span> Landing/take off surface of an aircraft carrier

The flight deck of an aircraft carrier is the surface from which its aircraft take off and land, essentially a miniature airfield at sea. On smaller naval ships which do not have aviation as a primary mission, the landing area for helicopters and other VTOL aircraft is also referred to as the flight deck. The official U.S. Navy term for these vessels is "air-capable ships".

<span class="mw-page-title-main">Martin AM Mauler</span> 1944 attack aircraft family by the Glenn L. Martin Company

The Martin AM Mauler was a single-seat carrier-based attack aircraft built for the United States Navy. Designed during World War II, the Mauler encountered development delays and did not enter service until 1948 in small numbers. The aircraft proved troublesome and remained in frontline service only until 1950, when the Navy switched to the smaller and simpler Douglas AD Skyraider. Maulers remained in reserve squadrons until 1953. A few were built as AM-1Q electronic-warfare aircraft with an additional crewman in the fuselage.

<span class="mw-page-title-main">Northrop Grumman X-47A Pegasus</span> Type of aircraft

The Northrop Grumman X-47 is a demonstration unmanned combat aerial vehicle. The X-47 began as part of DARPA's J-UCAS program, and is now part of the United States Navy's UCAS-D program to create a carrier-based unmanned aircraft. Unlike the Boeing X-45, initial Pegasus development was company-funded. The original vehicle carries the designation X-47A Pegasus, while the follow-on naval version is designated X-47B.

<span class="mw-page-title-main">Aircraft catapult</span> Device used to launch aircraft from ships

An aircraft catapult is a device used to allow aircraft to take off in a limited distance, typically from the deck of a vessel. They can also be installed on land-based runways, although this is rarely done. They are usually used on aircraft carriers as a form of assisted take off.

<span class="mw-page-title-main">Vought F7U Cutlass</span> US Navy carrier-based fighter-bomber aircraft in service 1951–1959

The Vought F7U Cutlass was a United States Navy carrier-based jet fighter and fighter-bomber designed and produced by the aircraft manufacturer Chance Vought. It was the first tailless production fighter in the United States as well as the Navy's first jet equipped with swept wings and the first to be designed with afterburners.

Italian aircraft carrier <i>Aquila</i> Italian aircraft carrier

Aquila was an Italian aircraft carrier converted from the transatlantic passenger liner SS Roma. During World War II, Work on Aquila began in late 1941 at the Ansaldo shipyard in Genoa and continued for the next two years. With the signing of the Italian armistice on 8 September 1943, however, all work was halted and the vessel remained unfinished. She was captured by the National Republican Navy of the Italian Social Republic and the German occupation forces in 1943, but in 1945 she was partially sunk by a commando attack of Mariassalto, an Italian royalist assault unit of the Co-Belligerent Navy of the Kingdom of Italy, made up by members of the former Decima Flottiglia MAS. Aquila was eventually refloated and scrapped in 1952.

<span class="mw-page-title-main">Tailhook</span> Aircraft device which allows arrested landings on aircraft carriers

A tailhook, arresting hook, or arrester hook is a device attached to the empennage (rear) of some military fixed-wing aircraft. The hook is used to achieve rapid deceleration during routine landings aboard aircraft carrier flight decks at sea, or during emergency landings or aborted takeoffs at properly equipped airports.

<span class="mw-page-title-main">Learjet 25</span> Type of aircraft

The Learjet 25 is an American ten-seat, twin-engine, high-speed business jet aircraft manufactured by Learjet. It is a stretched version of the Learjet 24.

<span class="mw-page-title-main">Landing signal officer</span>

A landing signal officer or landing safety officer (LSO), also informally known as paddles or batsman, is a naval aviator specially trained to facilitate the "safe and expeditious recovery" of naval aircraft aboard aircraft carriers. LSOs aboard smaller air capable ships that launch and recover helicopters are informally known as deck. Originally LSOs were responsible for bringing aircraft aboard ship using hand-operated signals. Since the introduction of optical landing systems in the 1950s, LSOs assist pilots by giving information via radio handsets.

<span class="mw-page-title-main">Bolter (aeronautics)</span> Aircraft that fails to hook onto aircraft carrier runway

In naval aviation, a bolter occurs when an aircraft attempting an arrested landing on the flight deck of an aircraft carrier touches down, but fails to catch an arrestor cable and come to a stop. Bolter aircraft accelerate at full throttle and become airborne in order to go-around and re-attempt the landing.

<span class="mw-page-title-main">Modern United States Navy carrier air operations</span> US aircraft carrier uniform colors

Modern United States Navy aircraft carrier air operations include the operation of fixed-wing and rotary aircraft on and around an aircraft carrier for performance of combat or noncombat missions. The flight operations are highly evolved, based on experiences dating back to 1922 with USS Langley.

Aircraft can have different ways to take off and land. Conventional airplanes accelerate along the ground until sufficient lift is generated for takeoff, and reverse the process to land. Some airplanes can take off at low speed, this being a short takeoff. Some aircraft such as helicopters and Harrier jump jets can take off and land vertically. Rockets also usually take off vertically, but some designs can land horizontally.

<span class="mw-page-title-main">Shipborne rolling vertical landing</span> Method of aircraft landing

Shipborne rolling vertical landing (SRVL) is a method used to land a V/STOL aircraft that uses both the vertical thrust from the jet engine and lift from the wings.

<span class="mw-page-title-main">Advanced Arresting Gear</span> Aircraft arresting system

The Advanced Arresting Gear (AAG) is a type of arresting gear developed by General Atomics for the U.S. Navy's newest Gerald R. Ford-class aircraft carriers. It was deployed in 2017 on the lead ship of the class, the USS Gerald R. Ford (CVN-78).

An aircraft ground carriage is a landing gear system connected to the ground, on which aircraft can take off and land without their aircraft-installed landing gear. The technical feasibility of the ground carriage is being investigated by two research groups. In 2013, IATA included the technology into their "Technology Roadmap"; Airbus pursues the concept as part of its "Future by Airbus” strategy.

<span class="mw-page-title-main">Ski-jump (aviation)</span> Take-off ramp for aircraft

In aviation, a ski-jump is an upward-curved ramp that allows aircraft to take off from a runway that is shorter than the aircraft's required takeoff roll. By forcing the aircraft upwards, lift-off can be achieved at a lower airspeed than that required for sustained flight, while allowing the aircraft to accelerate to such speed in the air rather than on the runway. Ski-jumps are commonly used to launch airplanes from aircraft carriers that lack catapults.

References

  1. "C. C. Mitchell". Graces Guide.
  2. 1 2 3 Mola, Roger (June–July 2015). "An Aircraft Carrier's Cable Guys". Air & Space. Retrieved 10 May 2018.
  3. Keegan, John (1989). The Price of Admiralty . New York: Viking. p.  276. ISBN   0-670-81416-4.
  4. "OK two wire! Ronald Reagan (CVN 76) ramps up new technology". thefreelibrary.com. 1 July 2002.
  5. Hearst Magazines (May 1954). "'Tennis Net' Crash Barrier Halts Jets at End of Runway". Popular Mechanics. Hearst Magazines. p. 127.
  6. 1 2 3 4 5 "Aviation Boatswain's. Mate E. NAVEDTRA 14310 (Nonresident Training Course)" (PDF). GlobalSecurity.org. Naval Education and Training Professional Development and Technology Center. July 2001. Archived from the original (PDF) on 18 October 2014.
  7. CV NATOPS, pp. 6–8.
  8. "Runway Arrestor Gear Systems - SKYbrary Aviation Safety". skybrary.aero. Retrieved 5 September 2021.
  9. "New Jet-landing Method Permits Aircraft to Stop Within 100 Yard". Popular Mechanics. Hearst Magazines. April 1957. p. 119.
  10. "World News – Spray Type Arrest Gear" Flight International, 9 August 1962.
  11. Rodriguez, Carmelo. "Launch and Recovery Testing". ITEA-SAN. Turboelectric Arresting Gear. Mission Valley Hotel, San Diego. 16 June 2005.