Automatic lubrication systems (ALS), also known as centralized lubrication systems (CLS), are mechanical devices used in industrial machines and engines to apply specified quantities of a lubricant to distribution points while the machine is operating. [1]
An automatic lubrication system consists of a reservoir with a pump, feed lines, metering valves, and injectors. The automatic lubrication system is connected to a control system via switchs. The control system may involve human input or may be computerised (computer numerical control or CNC). [2] [3]
There are advantages of using an automatic lubrication system over a manual system.
For example, there are savings in the costs of human resources. The dangers of accessing difficult to reach lubrication points while a machine is running are avoided. Machines can be running when lubrication takes place, thus decreasing disruption to production. Manual lubrication may result in over- or under-lubrication whereas an automatic lubrication system ensures a measured and consistent amount of lubricant is applied. (Over-lubrication can result in over-heating, spoiled product, damage to bearing seals and a need for extra cleaning. Under-lubrication can result in higher running costs and decreased machine longevity.) Effective lubrication reduces wear and therefore extends component life. Breakdowns are less frequent. Adequate lubrication decreases friction and therefore energy consumption. [4] [5]
Automatic lubrication systems can be categorised according to the type of lubricant, the method of controlling the volume of lubricant and or the method of distributing the lubricant. [6]
Oil systems are used in stationary machinery such as a CNC mill, for example. Grease systems are used in mobile machines such as trucks, mining and construction equipment. The appropriate lubricant for an automatic lubrication system can be determined using a Lincoln ventmeter. Factors such as the lubricant consistency, the diameter and length of the feed line and the operating temperature are taken into account. [7] The lubricant, be it oil or grease, is dispensed from a reservoir. The systems can be monitored remotely and managed by control systems. [8] The scientific study of factors such as these is called tribology. [9]
Pressure-relief systems (also called piston lubrication systems or positive displacement injector (PDI) systems) use a piston to apply an accurate lubricant volume to the lubrication point. A pressure relief system is used when the volume of lubricant applied must be precise. [10]
Resistant oil lubricators use the resistance of an outlet to control a continuous flow of lubricant. Further control is given by proportion adapters or oil meter adapters. Resistant oil lubricators are used when a precise volume of lubricant is less essential. [11]
There are a variety of feed line systems used in automatic lubricating systems. These include single-line progressive systems, single line parallel systems, dual-line parallel systems, mist lubrication and multiport direct lubricators. [12] [13]
A single-line progressive system uses the flow of the lubricant itself to cause individual metering valves and valve assemblies to cycle. The cycling of the valve causes the pistons to move back and forth in a cylinder of a specific diameter (bore). When a piston moves forward, it displaces lubricant which, in turn, causes the next piston to move forwards. The valve output is a fixed volume however, the amount of time taken for each piston to move back and forth can be varied and pre-programmed. Lubrications points are arranged in series. [14]
The first single-line parallel system for industrial machines was introduced in 1937 by Lincoln Engineering (now known as Lincoln Industrial) in the United States.
A single-line parallel system can apply lubricant in a single machine, different zones of lubricant points on a single machine, or even a number of separate machines using hydraulic pressure. It is most useful when the required volume of lubricant varies from one lubricant point to another. In this type of system, a central pump station automatically delivers lubricant through a single supply line to multiple branches of injectors. Each injector serves a single lubrication point, operates independently, and may be individually adjusted to deliver the desired amount of lubricant. [15] [16]
When the system is started, a pump increases the pressure of lubricant throughout the system to a set point. A pressure switch signals the control system that lubricant has been applied at all the lubricant distribution points have been reached. The pump stops, pressure is vented from the system and the lubricant is directed back to the pump reservoir. [16]
A dual-line parallel system also uses hydraulic pressure to apply lubricant in measured amounts. In an alternating pattern, one line is building hydraulic pressure while the other is venting pressure. The dual-line parallel system can apply lubricant to hundreds of lubricant distribution points located over several thousands of feet while using a single pump and relatively small diameter feed lines. [17]
A multipoint direct lubricator system uses a control system, to engage a drive motor, to turn a set of cams, which activate injectors at the lubricant distribution points. This type of system is easy to designs and troubleshoot. It can achieve automatic lubrication without accessories. [18]
A lubricant is a substance that helps to reduce friction between surfaces in mutual contact, which ultimately reduces the heat generated when the surfaces move. It may also have the function of transmitting forces, transporting foreign particles, or heating or cooling the surfaces. The property of reducing friction is known as lubricity.
An air-start system is a power source used to provide the initial rotation to start large diesel engines and gas turbines.
An air compressor is a machine that takes ambient air from the surroundings and discharges it at a higher pressure. It is an application of a gas compressor and a pneumatic device that converts mechanical power into potential energy stored in compressed air, which has many uses. A common application is to compress air into a storage tank, for immediate or later use. When the delivery pressure reaches its set upper limit, the compressor is shut off, or the excess air is released through an overpressure valve. The compressed air is stored in the tank until it is needed. The pressure energy provided by the compressed air can be used for a variety of applications such as pneumatic tools as it is released. When tank pressure reaches its lower limit, the air compressor turns on again and re-pressurizes the tank. A compressor is different from a pump because it works on a gas, while pumps work on a liquid.
Lubrication is the process or technique of using a lubricant to reduce friction and wear and tear in a contact between two surfaces. The study of lubrication is a discipline in the field of tribology.
Aircraft engine controls provide a means for the pilot to control and monitor the operation of the aircraft's powerplant. This article describes controls used with a basic internal-combustion engine driving a propeller. Some optional or more advanced configurations are described at the end of the article. Jet turbine engines use different operating principles and have their own sets of controls and sensors.
A diving air compressor is a breathing air compressor that can provide breathing air directly to a surface-supplied diver, or fill diving cylinders with high-pressure air pure enough to be used as a hyperbaric breathing gas. A low pressure diving air compressor usually has a delivery pressure of up to 30 bar, which is regulated to suit the depth of the dive. A high pressure diving compressor has a delivery pressure which is usually over 150 bar, and is commonly between 200 and 300 bar. The pressure is limited by an overpressure valve which may be adjustable.
Hydraulic machines use liquid fluid power to perform work. Heavy construction vehicles are a common example. In this type of machine, hydraulic fluid is pumped to various hydraulic motors and hydraulic cylinders throughout the machine and becomes pressurized according to the resistance present. The fluid is controlled directly or automatically by control valves and distributed through hoses, tubes, or pipes.
An automatic lubricator is a device fitted to a steam engine to supply lubricating oil to the cylinders and, sometimes, the bearings and axle box mountings as well. There are various types of automatic lubricator, which include various designs of displacement, hydrostatic and mechanical lubricators.
Within piston engines, a wet sump is part of a lubrication system whereby the crankcase sump is used as an integral oil reservoir. An alternative system is the dry sump, whereby oil is pumped from a shallow sump into an external reservoir.
An axial piston pump is a positive displacement pump that has a number of pistons in a circular array within a cylinder block.
A rotary-screw compressor is a type of gas compressor, such as an air compressor, that uses a rotary-type positive-displacement mechanism. These compressors are common in industrial applications and replace more traditional piston compressors where larger volumes of compressed gas are needed, e.g. for large refrigeration cycles such as chillers, or for compressed air systems to operate air-driven tools such as jackhammers and impact wrenches. For smaller rotor sizes the inherent leakage in the rotors becomes much more significant, leading to this type of mechanism being less suitable for smaller compressors than piston compressors.
A pneumatic lubricator injects an aerosolized stream of oil into an air line to provide lubrication to the internal working parts of pneumatic tools, and to other devices such as actuating cylinders, valves, and motors.
Lincoln Industrial Corporation (Lincoln) is a manufacturer of automated lubrication systems, manual lubrication equipment and industrial pumping systems, and subsidiary of Svenska Kullagerfabriken AB (SKF). Founded in 1910, the company has been responsible for many of the inventions that established modern lubrication practices in automotive maintenance and industry.
Graco Inc. is an American industrial company specializing in the development and manufacturing of fluid-handling systems and products. The company is headquartered in Minneapolis, Minnesota, and markets its products to customers worldwide.
Internal combustion engines come in a wide variety of types, but have certain family resemblances, and thus share many common types of components.
High-density solids pumps are hydrostatically operating machines which displace the medium being pumped and thus create a flow.
High-speed steam engines were one of the final developments of the stationary steam engine. They ran at a high speed, of several hundred rpm, which was needed by tasks such as electricity generation.
Oil mist lubrication is a method of lubricating machinery and equipment that involves delivering a fine mist or aerosol of oil particles into the lubrication points where friction and wear occur. Oils are applied to rolling element (antifriction) bearings as an oil mist. Neither oil rings nor constant level lubricators are used in pumps and drivers connected to plant-wide oil mist systems. Oil mist is an atomized amount of oil carried or suspended in a volume of pressurized dry air. The oil mist, actually a ratio of one volume of oil suspended or carried in 200,000 volumes of clean, dry air, moves in a piping system (header). The point of origin is usually a mixing valve, connected to this header. Branch lines often feed oil mist to hundreds of rolling elements in the many pumps and drivers connected to a plant-wide system.
A total-loss oiling system is an engine lubrication system whereby oil is introduced into the engine and then either burned or ejected overboard. Now rare in four-stroke engines, total loss oiling is still used in many two-stroke engines.
An internal combustion engine is a heat engine in which the combustion of a fuel occurs with an oxidizer in a combustion chamber that is an integral part of the working fluid flow circuit. In an internal combustion engine, the expansion of the high-temperature and high-pressure gases produced by combustion applies direct force to some component of the engine. The force is typically applied to pistons, turbine blades, a rotor, or a nozzle. This force moves the component over a distance. This process transforms chemical energy into kinetic energy which is used to propel, move or power whatever the engine is attached to.