An automatic lubricator is a device fitted to a steam engine to supply lubricating oil to the cylinders and, sometimes, the bearings and axle box mountings as well. [1] There are various types of automatic lubricator, which include various designs of displacement, hydrostatic and mechanical lubricators.
The displacement lubricator was introduced in the United Kingdom in 1860 by John Ramsbottom. It operates by allowing steam to enter a closed vessel containing oil. After condensing, the water sinks to the bottom of the vessel, causing the oil to rise and overflow into delivery pipes. The oil from the delivery pipes is introduced into the steam pipe, where it is atomised and carried to the valves and cylinders.
In early applications in steam locomotives, either two displacement lubricators (one for each cylinder) would be positioned at the front of the boiler near the valves, often on either side of the smokebox or one lubricator would be placed behind the smokebox. The behind-smokebox configuration has the advantage that a good connection can be made to the steam pipe and it was used by the Great Western Railway. It has the disadvantage that the lubricator's accessibility is reduced and additional drain pipes are required to be connected to the waste to avoid it dripping onto the boiler. [2]
Elijah McCoy, a Canadian who moved to Michigan and became a U.S. citizen, received a patent for his automatic lubricator in 1872. Piping delivered oil by gravity from a central reservoir to where it was required. Later types of lubricator (from around 1887 [2] ), referred to as the "sight-feed" type, allowed a sight glass to be positioned in the cab where the rate of oil feed could be observed. In 1898 McCoy's further patent added a glass tube mounted below the reservoir so that the rate of delivery could be monitored, with a bypass pipe available in case the main feed was seen to be blocked. [3]
The displacement lubricator was a useful stop-gap but had the disadvantage that it was difficult to accurately control over the rate of oil feed and lubrication was only supplied when the engine was doing work (when a locomotive is coasting with the regulator closed, no steam is present to operate the lubricator).
The Roscoe type lubricator improved the situation by providing a valve with which to regulate the flow of steam and hence lubricant. Setting the valve correctly required experience and depended on the speed of the train. [2]
The Roscoe lubricator was invented by James Roscoe in 1862 and patented in British Patent 1337. It incorporated two improvements over the original Ramsbottom type, the ability to control the quantity of steam which entered the lubricator, via a control valve, and the addition of an air filled chamber within the oil reservoir. The chamber expanded when steam was cut off, the aim of which was to supply oil even when the locomotive was coasting. However, this proved ineffective in practice, particularly if the locomotive was coasting for a long time (e.g. down a hill). [2]
When more sophisticated lubricators, such as the Wakefield and Detroit types, were developed, displacement lubricators fell out of use but they are still used on model steam engines. [4]
The one-piece lubricator body is a gunmetal casting and incorporates the condensing chamber, the oil reservoir and the sight-glasses fitted at the front and back of the body. Passages within the body interconnect these areas. The body is fitted with a steam valve, a water valve and oil control valves. In operation, steam enters the condensing chamber and the condensed water passes into the bottom of the oil reservoir and the sight-glass chambers. When the sight-glass chambers have filled with water the oil delivery for each feed, regulated by control valves, is released upwards into the water-filled sight-glass chambers. The rate of delivery, typically two or three drops of oil through each feed per minute, is monitored by watching the progress of the drops as they rise through the water. The oil gathers above the water and passes into the delivery tubes. The body is fitted with a drain for emptying the condensed water from the oil chamber before it is refilled with oil. [5]
This type of hydrostatic displacement lubricator was made by the Detroit Lubricator Company of the USA. A British patent was granted in 1911 and this lubricator was then manufactured by the Vacuum Oil Company (later Mobil Oil) as the British Detroit Lubricator. This lubricator was commonly made with either 3,4 or 5 feeds, the center feed on the odd numbered lubricators was often used for supplying oil to the steam end of Westinghouse air compressors. [6]
The Wakefield Oil Company, a manufacturer of lubricating oils, was founded in London by Charles Wakefield in 1899. The company manufactured both hydrostatic and mechanical lubricators but it was best-known for its patent mechanical lubricator. Marketed as the Wakefield Lubricator it comprised a large oil chest (typically 1 imperial gallon (4.5 l; 1.2 US gal) for eight delivery tubes) with eccentric-operated pumps submerged within it. Regulation of the oil feed was achieved by adjustment of sleeve valves, which could be made to release oil back into the reservoir (instead of entering the feed tubes) at varying stages as the delivery stroke progressed. If the device were used to deliver heavy grade oil to the steam cylinders the reservoir was heated by a steam coil to allow the oil to pass more easily down the delivery tubes. [5] [7]
The Silvertown lubricator was designed and developed by the Midland Railway in 1911 and from 1922 was commercially available from Gresham and Craven. This style of mechanical lubricator was used by the London, Midland and Scottish Railway and latter by British Rail, as well as by the various UK private locomotive builders for export overseas. Commonly 2 lubricators were fitted, one for lubricating the cylinders and the second for lubricating the axleboxes. [6]
The lubricator is a self-contained unit with the drive mechanism fitted at one end, with the drive shaft running through the cast iron oil reservoir. The drive shaft is fitted with 2 hardened steel eccentrics which provide movement to the drive frame which runs in machined grooves in the oil reservoir. This drive frame reciprocates vertically which then drives the double acting independent oil pumps located in the oil reservoir. [6]
The lubricator is driven by a rod from the expansion link in locomotives valve gear. The rocking motion of this drive is converted to a rotary motion by a series of driving pawls contained in a clutch box. The lubricators were also fitted with a priming hand wheel on the outer face of the lubricator. [6]
The Friedmann system of mechanical lubricators included the DV & FSA type lubricators. This style of mechanical lubricator was designed & produced by Alex Friedmann KG of Austria. The DV type were then made under licence by in the US by the Nathan Manufacturing Co. & the type DV & FSA types in the UK by Davies & Metcalfe Ltd. [6]
Both types of lubricator are of the 'valveless' type, having no ball valves, springs or oil seals used in the operation of the pump units. [6]
The DV range was available in range of sizes with capacities ranging from 8 to 36 pints, and the number of feeds from 1 to 26. Each of the lubricators consist of a reservoir, a ratchet assembly, a sliding shaft assembly, and the pump units. A screwed oil filler cap is fitted to the lockable hinged lid of the reservoir and a sight glass for indicating the oil level is fitted to the front face of the reservoir. The pumps of the DV type lubricator are operated by a sliding shaft assembly, unlike the Silverton or Wakefield lubricators which are operated by a rotating camshaft. [6]
The FSA type lubricator differs by each pump having two separate pistons to control the pumping & distribution of oil. The pistons are driven by cams on the driving shaft. The driving shaft is driven via a means of a roller ratchet assembly which converts the reciprocating motion of the operating linkage to rotary motion. [6]
Known also as syphon lubrication, equipment using this method consists of reservoirs of oil with delivery pipes from the reservoir to the bearings, axleboxes, slide bars or horn blocks, mounted so that the open top ends of the pipes are above the maximum oil level. Assemblies called trimmings—bundles of worsted yarn tied around narrow wire frames—are tucked into the open ends of the delivery pipes so that a "tail" of threads drapes into the oil. Capillary action draws the oil over the lip of the pipe for delivery by gravity. Variation in delivery rates comes from adjusting the size and tightness of the worsted bundles. The bundles of wool are effective in filtering out harmful contamination but do not work properly should water enter the reservoir. [5] [8] [9]
A boiler is a closed vessel in which fluid is heated. The fluid does not necessarily boil. The heated or vaporized fluid exits the boiler for use in various processes or heating applications, including water heating, central heating, boiler-based power generation, cooking, and sanitation.
A steam locomotive is a locomotive that provides the force to move itself and other vehicles by means of the expansion of steam. It is fuelled by burning combustible material to heat water in the locomotive's boiler to the point when it becomes gaseous and its volume increases 1,700 times. Functionally, it is a steam engine on wheels.
An injector is a system of ducting and nozzles used to direct the flow of a high-pressure fluid in such a way that a lower pressure fluid is entrained in the jet and carried through a duct to a region of higher pressure. It is a fluid-dynamic pump with no moving parts except a valve to control inlet flow. A steam injector is a typical application of the principle used to deliver cold water to a boiler against its own pressure, using its own live or exhaust steam, replacing any mechanical pump. When first developed, its operation was intriguing because it seemed paradoxical, almost like perpetual motion, but it was later explained using thermodynamics. Other types of injector may use other pressurised motive fluids such as air.
A fire-tube boiler is a type of boiler in which hot gases pass from a fire through one or more tubes running through a sealed container of water. The heat of the gases is transferred through the walls of the tubes by thermal conduction, heating the water and ultimately creating steam.
The Pennsylvania Railroad's class S2 was a steam turbine locomotive designed and built in a collaborative effort by Baldwin Locomotive Works and Westinghouse Electric & Manufacturing Company, as an attempt to prolong the dominance of the steam locomotive by adapting technology that had been widely accepted in the marine industry. One was built, #6200, delivered in September 1944. The S2 was the sole example of the 6-8-6 wheel arrangement in the Whyte notation, with a six-wheel leading truck, eight driving wheels, and a six-wheel trailing truck. The S2 used a direct-drive steam turbine provided by the Westinghouse Electric & Manufacturing Company, geared to the center pair of axles with the outer two axles connected by side rods; the fixed gear ratio was 18.5:1. Such design was to prevent energy loss and S2 achieved a mechanical efficiency of 97% which means only 3% of steam energy was lost within the propulsion equipment. The disadvantage of direct-drive steam turbine was that the turbine could not operate at optimal speeds over the locomotive's entire speed range. The S2 was the largest, heaviest and fastest direct-drive turbine locomotive design ever built.
A superheater is a device used to convert saturated steam or wet steam into superheated steam or dry steam. Superheated steam is used in steam turbines for electricity generation, steam engines, and in processes such as steam reforming. There are three types of superheaters: radiant, convection, and separately fired. A superheater can vary in size from a few tens of feet to several hundred feet.
Hydraulic machines use liquid fluid power to perform work. Heavy construction vehicles are a common example. In this type of machine, hydraulic fluid is pumped to various hydraulic motors and hydraulic cylinders throughout the machine and becomes pressurized according to the resistance present. The fluid is controlled directly or automatically by control valves and distributed through hoses, tubes, or pipes.
Priming is a condition in the boiler of a steam locomotive in which water is carried over into the steam delivery. It may be caused by impurities in the water, which foams up as it boils, or simply too high a water level. It is harmful to the valves and pistons, as lubrication is washed away, and can be dangerous as any water collecting in the cylinders is not compressible and if trapped may fracture the cylinder head or piston.
A reciprocating pump is a class of positive-displacement pumps that includes the piston pump, plunger pump, and diaphragm pump. Well maintained, reciprocating pumps can last for decades. Unmaintained, however, they can succumb to wear and tear. It is often used where a relatively small quantity of liquid is to be handled and where delivery pressure is quite large. In reciprocating pumps, the chamber that traps the liquid is a stationary cylinder that contains a piston or plunger.
The South African Railways Class 25NC 4-8-4 of 1953 was a steam locomotive.
The South African Railways Class 25 4-8-4 of 1953 was a condensing steam locomotive.
The South African Railways Class 19D 4-8-2 of 1937 was a steam locomotive.
The South African Railways Class 10B 4-6-2 of 1910 was a steam locomotive from the pre-Union era in Transvaal.
The South African Railways Class 10A 4-6-2 of 1910 was a steam locomotive from the pre-Union era in Transvaal.
The South African Railways Class GA 2-6-0+0-6-2 of 1921 was an articulated steam locomotive.
The South African Railways Class GM 4-8-2+2-8-4 of 1938 was an articulated steam locomotive.
High-speed steam engines were one of the final developments of the stationary steam engine. They ran at a high speed, of several hundred rpm, which was needed by tasks such as electricity generation.
The Austin 25-30 is a motor car. It was the first automobile produced by newly established British car manufacturer Austin.
A total-loss oiling system is an engine lubrication system whereby oil is introduced into the engine, and then either burned or ejected overboard. Now rare in four-stroke engines, total loss oiling is still used in many two-stroke engines.
The Cape Government Railways 3rd Class 4-4-0 of 1883 was a South African steam locomotive from the pre-Union era in the Cape of Good Hope.
