A blowing house or blowing mill was a building used for smelting tin in Cornwall and on Dartmoor in Devon, in South West England. Blowing houses contained a furnace and a pair of bellows that were powered by an adjacent water wheel, and they were in use from the early 14th century until they were gradually replaced by reverberatory furnaces in the 18th century. The remains of over 40 blowing houses have been identified on Dartmoor.
The blowing house method of smelting tin was probably introduced early in the 14th century to replace the earliest method of smelting which had to be done in two stages – a first smelting probably took place near to the tinworks and the roughly smelted metal was taken to a stannary town to be smelted again to produce the final refined product. [1] Each of these smeltings was taxed separately until 1303 when they were replaced by a single tax on the finished product. It is likely that this tax change was due to the improved smelting process provided by the blowing houses. [1]
totum illud molendinium ibidem vocatum a blowyng myll & knakkyng myll
Documentation confirms the existence of blowing houses in Cornwall as early as 1402, but the earliest reference for Dartmoor is not found until the early 16th century, though it is likely that they were in use on the moor earlier. [1] In Devon there are many references to blowing mills throughout the 16th and 17th centuries, reflecting the boom time in tin-mining on Dartmoor. However, by 1730 there were only two blowing mills working in the whole of the county: at Sheepstor and Plympton. [1]
From the beginning of the 18th century, this method was gradually superseded by reverberatory furnace smelting, which used higher temperatures and powdered anthracite as fuel and had the advantage of not requiring a forced draught of air. The smelting house at Eylesbarrow tin mine which was in operation during the first half of the 19th century had two furnaces, one of each type. [2]
On Dartmoor, blowing houses were rectangular buildings between around 16 to 32 feet (4.9 to 9.8 m) in length and around half this in width. [3] They were made of unmortared granite blocks with walls often 2 feet 6 inches (0.76 m) or more thick and probably had turf or thatch roofs which were periodically burnt to retrieve the particles of tin that would have been driven into the roof through the blast from the bellows. [4] Blowing houses are typically located on or near the bank of a stream where the fall of water was enough for a leat to be built to work a small (9 ft or 2.7 m) diameter overshot water wheel which developed around 0.66 hp (0.5 kW) to operate the bellows. [4]
The only contemporary detailed description of a blowing house was provided by a Cornishman named William Pryce in his treatise on Cornish mining of 1778: [1]
The fire-place, or castle, is about six feet perpendicular, two feet wide in the top part each way, and about fourteen inches in the bottom, all made of moorstone and clay, well cemented and clamped together. The pipe or nose of each bellows is fixed ten inches (254 mm) high from the bottom of the castle, in a large piece of wrought iron, called the Hearth-eye. The tin and charcoal are laid in the castle, stratum super stratum, in such quantities as are thought proper; so that from eight to twelve hundred weight of Tin, by the consumption of eighteen to twenty-four sixty gallon packs of charcoal, may be smelted in a tide or twelve hours time. [5]
According to Crispin Gill, about two tons of charcoal was needed to smelt a ton of metal. The molten metal ran out from the bottom of the furnace into a granite trough or "float" from where it was ladled into stone moulds. [4]
Archaeological investigation of blowing houses started in 1866 when John Kelly examined the lower mill at Yealm Steps. Robert Burnard cleared the interior of the lower mill at Week Ford in the 1880s, but the most notable researcher of the remains on Dartmoor was R. Hansford Worth who made detailed records of over 40 sites. [1] Since then, research on the tin industry in the south west has continued, for instance The Dartmoor Tinworking Interest Group was formed in 1991. [1]
There is evidence for furnaces that match the description given by Pryce (see above) at Upper and Lower Merrivale, Avon Dam and Blacksmith's Shop. Each of these sites has two upright granite slabs about 2 to 3 feet (0.61 to 0.91 m) apart set into the floor area of the mill, leaving space behind for the bellows. The Merrivale sites also have a slab at the back, making a basic hearth shape. [1] The accompanying photograph shows the two side slabs of the furnace at the Lower Merrivale blowing house, with the somewhat displaced float stone between them. The mouldstone, filled with rainwater, is just above and to the right.
The mouldstone is the best field evidence for a blowing house; they are large blocks of granite with a flat top containing a rectangular hollow recess into which the molten tin was poured to be cast into ingots. The moulds vary in size and shape, the largest known from Dartmoor being that from Upper Merrivale at 280 by 390 millimetres (11 in × 15 in), and the smallest 180 millimetres (7.1 in) square at Longstone. Some mouldstones have additional smaller hollows on their surface; these are traditionally assumed to be for assaying purposes, but some authors have suggested that they may have been for making small ingots for selling illicitly to avoid tin coinage, the tax on white, or refined tin. [1]
The only properly documented find of a tin ingot from Dartmoor has a diagonal hole through it which matches the supposed practice of placing a stick in the mould when pouring in the molten tin. The stick would burn away leaving the hole which would be used to lever out the solid ingot from the mould and would later be useful to tie up the ingots for carriage. [1] According to Worth, the found ingot fitted precisely into one of the moulds found at the lower blowing house on the River Yealm, although it did not fill it and weighed only 52 pounds (24 kg), far less than the average Dartmoor ingot weight of 195 pounds (88 kg). He speculated that it was the small surplus that remained after the normal ingots had been cast. [3] Cornish ingots were much larger, averaging around 345 pounds (156 kg). [3]
One of the best preserved blowing houses on Dartmoor is above Merrivale Bridge on the River Walkham. It has a mould stone close to its entrance and the wheel-pit can be easily traced. [4] Some blowing houses also housed crushing ("knacking") or grinding ("crazing") mills, and at Gobbet Mine on the River Swincombe both the upper and lower grinding stones were found. [4]
The industrial archaeology of Dartmoor covers a number of the industries which have, over the ages, taken place on Dartmoor, and the remaining evidence surrounding them. Currently only three industries are economically significant, yet all three will inevitably leave their own traces on the moor: china clay mining, farming and tourism.
A blast furnace is a type of metallurgical furnace used for smelting to produce industrial metals, generally pig iron, but also others such as lead or copper. Blast refers to the combustion air being supplied above atmospheric pressure.
Copper extraction refers to the methods used to obtain copper from its ores. The conversion of copper ores consists of a series of physical, chemical and electrochemical processes. Methods have evolved and vary with country depending on the ore source, local environmental regulations, and other factors.
Merrivale is a locality in western Dartmoor, in the West Devon district of Devon, England. It is best known for the nearby series of Bronze Age megalithic monuments to the south and a former granite quarry.
The tin mining industry on Dartmoor, Devon, England, is thought to have originated in pre-Roman times, and continued right through to the 20th century, when the last commercially worked mine closed in November 1930. From the 12th century onwards tin mining was regulated by a stannary parliament which had its own laws.
The Erme is a river in south Devon, England. From its source on Dartmoor it flows in a generally southerly direction past some of the best-preserved archaeological remains on the moor. It leaves the moor at the town of Ivybridge and continues southward, passing the settlements of Ermington, Modbury and Holbeton. Near Holbeton it becomes a ria and empties into the English Channel in Bigbury Bay, between the rivers Yealm and Avon.
A bloomery is a type of metallurgical furnace once used widely for smelting iron from its oxides. The bloomery was the earliest form of smelter capable of smelting iron. Bloomeries produce a porous mass of iron and slag called a bloom. The mix of slag and iron in the bloom, termed sponge iron, is usually consolidated and further forged into wrought iron. Blast furnaces, which produce pig iron, have largely superseded bloomeries.
A reverberatory furnace is a metallurgical or process furnace that isolates the material being processed from contact with the fuel, but not from contact with combustion gases. The term reverberation is used here in a generic sense of rebounding or reflecting, not in the acoustic sense of echoing.
A stannary was an administrative division established under stannary law in the English counties of Cornwall and Devon to manage the collection of tin coinage, which was the duty payable on the metal tin smelted from the ore cassiterite mined in the region. In Cornwall, the duty was passed to the Duchy of Cornwall; in Devon to the Crown.
Mining in Cornwall and Devon, in the southwest of Britain, is thought to have begun in the early-middle Bronze Age with the exploitation of cassiterite. Tin, and later copper, were the most commonly extracted metals. Some tin mining continued long after the mining of other metals had become unprofitable, but ended in the late 20th century. In 2021, it was announced that a new mine was extracting battery-grade lithium carbonate, more than 20 years after the closure of the last South Crofty tin mine in Cornwall in 1998.
Whiteworks is a former mining hamlet near the town of Princetown, within Dartmoor National Park, in the English county of Devon. Tin mining is central to the history of settlement at Whiteworks, which was once home to one of Dartmoor's largest tin mines. The original cottages and their inhabitants were related to this industry, until the area became used increasingly for farming in the 20th century. The site has now largely been abandoned, although Whiteworks is still on the route of many walks including Abbots Way Walk passes 500 m to the west.
Metals and metal working had been known to the people of modern Italy since the Bronze Age. By 53 BC, Rome had expanded to control an immense expanse of the Mediterranean. This included Italy and its islands, Spain, Macedonia, Africa, Asia Minor, Syria and Greece; by the end of the Emperor Trajan's reign, the Roman Empire had grown further to encompass parts of Britain, Egypt, all of modern Germany west of the Rhine, Dacia, Noricum, Judea, Armenia, Illyria, and Thrace. As the empire grew, so did its need for metals.
Eylesbarrow mine was a tin mine on Dartmoor, Devon, England that was active during the first half of the 19th century. In its early years it was one of the largest and most prosperous of the Dartmoor tin mines, along with Whiteworks and the Birch Tor and Vitifer mines. Its name has several variant spellings, such as Eylesburrow, Ailsborough, Ellisborough, Hillsborough etc. It was also known as Wheal Ruth for a short period around 1850. The extensive remains lie to the north of the River Plym, less than 1 mile (1.6 km) north-east of Drizzlecombe, on the southern shoulder of the hill called Eylesbarrow on top of which are two prominent Bronze Age barrows.
Birch Tor and Vitifer mine was a tin mine on Dartmoor, Devon, England. Located in the valley of the Redwater Brook, to the east of the B3212 Moretonhampstead to Princetown road, below the Warren House Inn, the mine was worked between the mid–18th century and 1925.
Dendles Wood is an area of protected oak-beech woodland located on the southern edge of Dartmoor, in the English county of Devon. Forming part of the Dartmoor Special Area of Conservation, the wood is also a Site of Special Scientific Interest, and 30 hectares of it has been designated a national nature reserve. It is one of five woodlands within Dartmoor that have been protected as national nature reserves. Dendles Wood and the adjacent Hawns Wood are sometimes known collectively as Hawns and Dendles. The wood supports a variety of flora and fauna, representative of upland oakwoods. In particular, it has a rich variety of moss and lichen, and several breeding bird species.
Plants for the production of lead are generally referred to as lead smelters. Primary lead production begins with sintering. Concentrated lead ore is fed into a sintering machine with iron, silica, limestone fluxes, coke, soda ash, pyrite, zinc, caustics or pollution control particulates. Smelting uses suitable reducing substances that will combine with those oxidizing elements to free the metal. Reduction is the final, high-temperature step in smelting. It is here that the oxide becomes the elemental metal. A reducing environment pulls the final oxygen atoms from the raw metal.
The Bottom-blown Oxygen Converter or BBOC is a smelting furnace developed by the staff at Britannia Refined Metals Limited (“BRM”), a British subsidiary of MIM Holdings Limited. The furnace is currently marketed by Glencore Technology. It is a sealed, flat-bottomed furnace mounted on a tilting frame that is used in the recovery of precious metals. A key feature is the use of a shrouded lance to inject oxygen through the bottom of the furnace, directly into the precious metals contained in the furnace, to oxidize base metals or other impurities as part of their removal as slag.
Sundown Tin and Copper Mine is a heritage-listed mine at Little Sundown Creek, Stanthorpe, Southern Downs Region, Queensland, Australia. It was built from c. 1897 to 1920s. It was added to the Queensland Heritage Register on 28 July 2000.
The Bonawe Iron Furnace, was an industrial complex located in Bonawe, Lorn District, Scotland. It operated in the middle of the eighteenth century, with the aim of producing pig iron. Central to this complex was a charcoal fired blast furnace.
Calenick HouseCalenick House is the principal part of a country house that forms a prominent collection of Grade II* listed buildings within the hamlet of Calenick, approximately 1 mile (1.6 km) south of the City of Truro in Cornwall. The site also houses a Grade II* clock tower, as well as a Grade II listed weigh house.
